User GuideIM C2000/C2500/C3000/C3500/C4500/C5500/C6000 series

Interface Settings (System Settings)

This section describes the settings in the [Interface Settings] menu under [System Settings].

Introduction of Two Types of Setting Screens (Standard/Classic)

Network/USB

This section describes the settings in the [Network/USB] menu under [Interface Settings] tab.

Items

Description

Machine IPv4 Address

Specify the machine's IPv4 Address and Subnet Mask. Machine's IPv4 Address can be specified by an address or acquired from the DHCP server automatically.

  • Default: [Auto-Obtain (DHCP)]

IPv4 Gateway Address

Specify the IPv4 address of the router or host computer used as a gateway.

  • Default: 0.0.0.0

Machine IPv6 Address

Displays the machine's IPv6 address.

  • Link-local Address

  • Manual Configuration Address

  • DHCPv6 Address

  • Stateless Address: 1–5

    Current value when [IPv6 Stateless Address Autoconfiguration] is specified to "Active" is displayed.

IPv6 Gateway Address

Displays the machine's IPv6 gateway address.

IPv6 Stateless Address Autoconfiguration

Specify whether to specify the address automatically using IPv6 Stateless Address Autoconfiguration.

  • Default: [Active]

DHCPv6 Configuration

Specify the DHCPv6 Mode or address of the DNS server.

  • Default: [Inactive]

DNS Configuration

Specify the IPv4 address of the DNS server. IPv4 Address of the DNS server can be specified by an address or acquired from the DHCP server automatically. You can confirm the connection to the DNS server.

  • Default: [Auto-Obtain (DHCP)]

DDNS Configuration

Specify whether you use the Dynamic DNS function.

  • Default: [Active]

IPsec

Specify whether to use the machine's IP sec.

  • Default: [Inactive]

For details about "Configuring IPsec Settings", see "Security Reference" on our website.

Domain Name

Specify the domain name. Obtain the domain name from the DHCP server automatically or enter the domain name up to 63 characters.

WINS Configuration

Specify whether to use WINS server.

When the machine's IPv4 address is specified optionally, specify the primary and secondary WIN server addresses and scope ID.

Do not specify "255.255.255.255" as the address of the WINS server.

  • Default: [On]

Effective Protocol

Select protocols to use in the network.

  • Default

    IPv4: [Active]

    IPv6: [Inactive]

    SMB: [Active]

    @Remote Service: [Active]

    Firmware Update (IPv4): [Active]

    Firmware Update (IPv6): [Active]

SMB Computer Name

Specify the SMB computer name. When you do not specify the name, the text starting with "RNP" is automatically set.

Enter the name up to 15 characters. You cannot specify a text starting with RNP. "*+,/:;<>=?[\]|. and spaces cannot be entered.

SMB Work Group

Specify the SMB work group name. Enter the group name up to 15 characters. "*+,/:;<>=?[\]|. and spaces cannot be entered.

  • Default: [WORKGROUP]

SMB Client Advanced Settings

Select the port number from 139 or 445 for the SMB data transmission. You can also specify whether to specify the SMBv2/v3 transmission Inactive. When SMBv2/v3 is Inactive, transmission is performed with SMBv1.

  • Default

    • Port Number: [445]

    • SMBv2/SMBv3: [Active]

Ethernet Speed

Specify the access speed between the machine and the network devices. When the communication is unstable, fix the Transmission Speed to 10 Mbps or 100 Mbps. When you specify Full Duplex in this case, specify the same Transmission Speed of the connected device as the machine.

  • Default: [Auto Select]: [Disable 1Gbps]

LAN Type

LAN type is displayed when wireless LAN board is installed. You can specify which you use for connection, wired LAN (Ethernet) or wireless LAN.

  • Default: [Ethernet]

Ping Command

Confirm whether the machine can be connected to the network. Specify the IPv4 address of the device connected to the network and then press [#]. A message to indicate whether the connection succeeded is displayed on the screen.

Permit SNMPv3 Communication

Specify the communication of SNMPv3 protocol whether to use the encrypted communication only or encrypted and cleartext communication in accordance with the settings of the machine.

When you specify [Encryption Only], you need to set [Encryption Password] for the administrator by [Administrator Tools] tab [Program / Change Administrator].

  • Default: [Encryption / Cleartext]

Permit SSL / TLS Communication

Specify the communication of SNMPv3 protocol whether to use the encrypted communication of SSL/TLS or encrypted and cleartext communication in accordance with the settings of the machine.

When you specify [Ciphertext Only], you need to install the Server Certificate for the machine.

  • Default: [Ciphertext / Cleartext]

Host Name

Specify the host name. When you do not specify the name, the text starting with RNP is automatically set.

Enter the host name up to 63 characters. You cannot specify the host name starting with "RNP" or "rnp".

You cannot enter a host name starting with or ending with a hyphen. You cannot enter a host name in which hyphens are used consecutively.

  • Default: [RNPXXXXX]

    (MAC Address of the Ethernet Interface is used for XXXXX.)

Machine Name

Enter the machine name up to 31 characters. When you manage the machine with Web Image Monitor or Machine Management software, this is displayed as "Device Name".

IEEE 802.1X Authentication for Ethernet

Specify when you use the IEEE 802.1X authentication for Ethernet.

  • Default: [Inactive]

For details about "Configuring IPsec Settings", see "Security Reference" on our website.

Restore IEEE 802.1X Authentication to Defaults

Return the settings to their defaults when the machine cannot be connected with the IEEE 802.1X authentication.

For details about "Configuring IPsec Settings", see "Security Reference" on our website.

USB Speed

Specify the USB speed. You can select from [Auto Select] or [Full Speed].

  • Default: [Auto Select]

USB Port

Specify whether to use the USB port.

Region A icon (mainly Europe)

  • Default: [Inactive]

Region B icon (mainly North America)

  • Default: [Active]

Region A icon (mainly Asia)

  • Default: [Active]

DIPRINT Timeout Period

Specify the timeout time for DIPRINT printing.

  • Default: [60 seconds]

Access Control Function

Specify whether to enable the function to permit the communication within the specified range of the IP addresses (Access Control).

  • Default: [Inactive]

Access Control

Note

  • We recommend only enabling one of the following settings: [IPv6 Gateway Address], [IPv6 Stateless Address Autoconfiguration], or [DHCPv6 Configuration]. If you enable all of them at the same time, IPv6 Gateway Address is automatically changed.

  • An IPv6 gateway address automatically acquired may be set by the router or in accordance with the DHCPv6 server settings if one of the following settings is enabled:

    • Activate [IPv6 Gateway Address] and either [IPv6 Stateless Address Autoconfiguration] or [DHCPv6 Configuration].

    • Activate [IPv6 Stateless Address Autoconfiguration] and [DHCPv6 Configuration] at the same time.

Parallel Interface

This section describes the settings in the [Parallel Interface] under [Interface Settings] tab.

This is displayed when the IEEE 1284 interface board is installed.

Items

Description

Parallel Timing

Specify the timing for the control signal of the parallel interface.

  • Default: [ACK Outside]

Parallel Communication Speed

Specify the communication speed for the parallel interface.

  • Default: [High Speed]

Selection Signal Status

Specify the level for the select signal of the parallel interface.

  • Default: [High]

Input Prime

Specify whether to validate or invalidate the input prime signal upon reception.

  • Default: [Inactive]

Bidirectional Communication

Specify the machine's response mode to a status acquisition request from the computer.

  • Default: [On]

Signal Control

Specify how to handle errors that occur during printing operation. Normally it is not necessary to change. When you specify [Printer Priority], the error is sent to the computer as it is.

  • Default: [Job Acceptance Priority]

Wireless LAN

This section describes the settings in the [Wireless LAN] menu under [Interface Settings].

This is displayed when wireless LAN board is installed.

Connecting to a Wireless LAN

Items

Description

Communication Mode

Specify the communication mode of the wireless LAN. The following modes are available:

[802.11 Ad-hoc Mode]

[Infrastructure Mode]

[Direct Connection: Group Owner Mode]

[Direct Connection Mode]

  • Default: [Infrastructure Mode]

Selecting the Network Connection Method

SSID Setting

Specify SSID when [Communication Mode] is [Infrastructure Mode] or [802.11 Ad-hoc Mode].

In [Infrastructure Mode] enter the SSID of the connected access point. In [802.11 Ad-hoc Mode], the entered SSID will be the name of the Ad-hoc network.

The characters that can be used are ASCII 0x20-0x7e (32 bytes), and are distinguished between upper and lower cases.

For connecting to the access point to which ANY connection is permitted, enter blank or "ANY" in the SSID field.

Ad-hoc Channel

Specify the channel to use when [Communication Mode] is [802.11 Ad-hoc Mode]. Select the channel depending on the radio wave status.

  • Default: [11]

Security Method

Specify the encryption of the Wireless LAN. To encrypt, select one of WEP, WPA2-PSK, or WPA2 as the Security Method. If you select WPA2, install the authentication methods and certificate.

For details about "Configuring IPsec Settings", see "Security Reference" on our website.

  • Default: [Off]

Wireless LAN: Easy Setup/Direct Connection

Specify Wireless LAN: Easy Setup/Direct Connection to connect to a WPS-compatible access point. Push the button of the access point or enter the PIN code displayed on the machine in the access point on the computer for the connection.

  • Default: [Push Button]

Direct Connection Settings

Specify to connect to the machine from the mobile device.

Specify the device name, password, machine's IPv4 address for direct connection.

Connecting to the Machine from a Mobile Device Using the Wi-Fi Direct Function

Wireless LAN Signal

Display the machine's radio wave status when the machine is connected by specifying [Communication Mode] to [Infrastructure Mode]. If the radio wave is weak, change the access point to connect or review the machine's environment.

Restore Factory Defaults

You can return the wireless LAN settings to their defaults.

Direct Connection

This section describes the settings in the [Direct Connection] menu under [Interface Settings].

This is displayed when wireless LAN board is installed.

Connecting to the Machine from a Mobile Device Using the Wi-Fi Direct Function

Items

Description

Active/Inactive

Specify whether to enable Direct Connection: Group Owner Mode set to Active from the direct connection widget placed on the Home screen.

  • Default: [Inactive]

Direct Connection Settings

Specify to connect to the machine from the mobile device.

Specify the device name, password, and machine's IPv4 address for direct connection.

Fix SSID

Specify whether to fix SSID when the direct connection is set to Active.

  • Default: [Off]

Printing the Interface Settings

1Press [Settings] on the Home screen.

Operation panel screen illustration

2Press [Machine Features Settings].

Operation panel screen illustration

3Press [System Settings][Interface Settings] tab to display the Interface Settings screen.

4Press [Print List].

Operation panel screen illustration

5Press [Start].

6After completing the list print, press [Home] (Operation panel screen illustration).