Alert Messages (in alphabetical order)

Open the front cover and remove any jammed paper. For details, see Paper Misfeed Message (A).

Open the front cover and remove any jammed paper from the internal paper feed path. For details, see Paper Misfeed Message (B).

Open the front cover and remove any jammed paper. For details, see Paper Misfeed Message (Y).

Open the front cover and remove any jammed paper from the paper transfer unit. For details, see Paper Misfeed Message (Z).

The waste toner bottle is almost full. Contact your sales or service representative to obtain a new waste toner bottle.

Replace the waste toner bottle. For details, see Replacing the Waste Toner Bottle.

Updating the @Remote certificate failed. Contact your sales or service representative.

The proxy user name or password is incorrect. Check the proxy server settings, and change the user name and/or password if they are incorrect.

Cannot obtain IP address from DHCP server. Consult your network administrator.

Connection with NetWare print server is unavailable.

Connection with NetWare server is unavailable. Consult your network administrator.

Check the file you want to print is a supported file type. Check for misfeeds and ask your network administrator for help.

The IP address setting is incorrect. Check the IP address, subnet mask, and gateway address. For details, see Ethernet Configuration.

A classification code is not specified for the print job. Enter a classification code using the printer properties and print the document again.

For details, see "Registering Classification Codes", Software Guide.

Check there is a Wireless LAN board installed.

Check that it is a supported board. If it is, check it is installed correctly.

Install the correct board properly. For details, see Installing the Interface Units.

Close the cover indicated on the control panel.

The duplex mode for the indicated tray is off; you can only use one-sided printing. Press [Change] to change the tray's settings, press [JobReset] to reset the job, or press [Form Feed] to force printing.

Auto power off by the [ECO Night Sensor] function failed. Turn off the power manually, or press any key to use [ECO Night Sensor] auto power off function.

An error on the Ethernet board is detected. Pull out and then re-install the controller board. If the problem persists, contact your sales or service representative.

The printer cannot communicate with Remote Communication Gate. Check the connection to the Remote Server Gate.

The same IPv6 address already exists. Consult your network administrator.

The same IPv6 address already exists. Consult your network administrator.

The same IPv6 address already exists. Consult your network administrator.

There is no paper in the specified tray. Load the specified paper in the tray, press [JobReset] to reset the job. To print from the bypass tray on paper whose width is less than 90 mm, cancel the print job, and then, under [System], set [Bypass Print: 64-90 mm] to [Active].

The output tray is full. Remove paper from the output tray.

The printer cannot detect an optional SDRAM module. It may be incorrectly installed.

Check if it is installed properly.

For details about installing the unit, see Installing the Memory Expansion Units.

The printer's self diagnostic test failed due to a loopback error. Replace the IEEE 1284 board that caused the error. For details, see Installing the Interface Units.

There are problems with the printer's font file.

Contact your sales or service representative.

The printer cannot detect a hard disk. It may be incorrectly installed.

Check if it is installed properly or contact your sales or service representative.

For details about installing the unit, see Installing the Memory Expansion Units.

The printer cannot detect a Wireless LAN board failure. It may be incorrectly installed.

Check if it is installed properly or contact your sales or service representative.

For details about installing the unit, see Installing the Interface Units.

The printer cannot detect a Wireless LAN board. It may be incorrectly installed.

Check if it is installed properly or contact your sales or service representative.

For details about installing the unit, see Installing the Interface Units.

You need to replace the intermediate transfer unit. Contact your sales or service representative to obtain a new intermediate transfer unit.

See Replacing the Intermediate Transfer Unit.

You need to replace the intermediate transfer unit. For details, see Replacing the Intermediate Transfer Unit.

You need to replace the fusing unit. For details, see Replacing the Maintenance Kit.

The toner has run out, or the photo conductor unit has reached the end of its service life. Replace the print cartridge. For details, see Replacing the Print Cartridge.

You will need to replace the intermediate transfer unit soon. Contact your sales or service representative to obtain a new unit.

You will need to replace the fusing unit soon. Contact your sales or service representative to obtain a new unit.

The toner has almost run out, or the photo conductor unit is nearing the end of its service life. Obtain a new print cartridge.

Authentication from the SD card failed. Turn the power off, and then back on. If the error recurs, contact your sales or service representative.

You need to clean the toner density sensor.

For details, see Cleaning the Toner Density Sensor.

There is no paper in the bypass tray. Load paper onto the bypass tray, and then press the [OK] key.

The fusing unit may not be installed correctly. Turn the printer off and re-install the fusing unit.

If the message is still displayed after re-installation, contact your sales or service representative.

For details, see Replacing the Maintenance Kit for fusing unit installation.

The intermediate transfer unit may not be installed correctly. Turn the printer off and re-install the intermediate transfer unit.

If the message is still displayed after re-installation, contact your sales or service representative.

For details, see Replacing the Intermediate Transfer Unit for intermediate transfer unit installation.

The print cartridge may not be installed correctly. Turn the printer off and re-install the Print cartridge.

If the message is still displayed after re-installation, contact your sales or service representative.

For details, see Replacing the Print Cartridge for Print cartridge installation.

The waste toner bottle may not be installed correctly. Turn the printer off and re-install the waste toner bottle.

If the message is still displayed after re-installation, contact your sales or service representative.

For details, see Replacing the Waste Toner Bottle.

The automatic supply order failed. The message indicates the supplies that the printer tried to order.

The NetBIOS name specified for the printer is already in use by another device on the network. Consult your network administrator.

The IPv4 address specified for the printer is already in use by another device on the network. Consult your network administrator.

This message might appear if you print or delete a job from Web Image Monitor. Press Exit on the message screen.

The printer has detected a USB board failure. Turn the power off, and then on again. If the problem persists, contact your sales or service representative.

The IPv6 address or gateway address is invalid. Check the network settings.

WPA authentication could not complete. Consult your network administrator.