Configuring the IPsec Policy

No.

IPsec policy number.

Name

Displays the name of the IPsec policy.

Address Settings

Displays the IP address filter of the IPsec policy as below:

Remote address/Prefix length

Action

Displays the action of the IPsec policy as “Allow”, “Drop”, or “Require Security”.

Status

Displays the status of the IPsec policy as “Active” or “Inactive”.

No.

Specify a number between 1 and 10 for the IPsec policy. The number you specify will determine the position of the policy in the IPsec Policy List. Policy searching is performed according to the order of the list. If the number you specify is already assigned to another policy, the policy you are configuring will take the number of the earlier policy, and the earlier policy and any subsequent policies will be renumbered accordingly.

Activity

Select whether to enable or disable the policy.

Name

Enter the name of the policy. Can contain up to 16 characters.

Address Type

Select IPv4 or IPv6 as the type of IP address to be used in IPsec communication.

Local Address

Displays the IP address of this printer.

Remote Address

Enter the IPv4 or IPv6 address of the device with which to communicate. Can contain up to 39 characters.

Prefix Length

Enter the prefix length of the Remote Address, using a value between 1 and 128. If this setting is left blank, "32" (IPv4) or "128" (IPv6) will be automatically selected.

Action

Specify how the IP packets are processed from the following:

• [Allow]: IP packets are both sent and received without IPsec applied to them.

• [Drop]: IP packets are discarded.

• [Require Security]: IPsec is applied to IP packets that are both sent and received.

  If you have selected [Require Security], you must configure [IPsec Settings] and [IKE Settings].

Encapsulation Type

Specify the encapsulation type from the following:

• [Transport]: Select this mode to secure only the payload section of each IP packet when communicating with IPsec compliant devices.

• [Tunnel]: Select this mode to secure every section of each IP packet. We recommend this type for communication between security gateways (such as VPN devices).

Security Protocol

Select the security protocol from the following:

• [AH]: Establishes secure communication that supports authentication only.

• [ESP]: Establishes secure communication that supports both authentication and data encryption.

• [ESP&AH]: Establishes secure communication that supports both data encryption and authentication of packets, including packet headers. Note that you cannot specify this protocol when [Tunnel] is selected for [Encapsulation Type].

Authentication Algorithm for AH

Specify the authentication algorithm to be applied when [AH] or [ESP&AH] is selected for [Security Protocol] from the following:

[MD5], [SHA1]

Encryption Algorithm for ESP

Specify the encryption algorithm to be applied when [ESP] or [ESP&AH] is selected for [Security Protocol] from the following:

[None], [DES], [3DES], [AES-128], [AES-192], [AES-256]

Authentication Algorithm for ESP

Specify the authentication algorithm to be applied when [ESP] is selected for [Security Protocol] from the following:

[MD5], [SHA1]

Life Time

Specify the life time of the IPsec SA (Security Association) as a time period or data volume. The SA will expire when the time period you specify elapses or the volume of data you specify reaches the volume carried.

If you specify both a time period and a data volume, the SA will expire as soon as either is reached, and a new SA will then be obtained by negotiation.

To specify the life time of the SA as a time period, enter a number of seconds.

To specify the life time of the SA as a data volume, enter a number of KBs.

Key Perfect Forward Secrecy

Select whether to enable or disable PFS (Perfect Forward Secrecy).

IKE Version

Displays the IKE version.

Encryption Algorithm

Specify the encryption algorithm from the following:

[DES], [3DES], [AES-128], [AES-192], [AES-256]

Authentication Algorithm

Specify the authentication algorithm from the following:

[MD5], [SHA1]

IKE Life Time

Specify the life time of the ISAKMP SA as a time period. Enter a number of seconds.

IKE Diffie-Hellman Group

Select the IKE Diffie-Hellman Group to be used in the generation of the IKE encryption key from the following:

[DH1], [DH2]

Pre-Shared Key

Specify the PSK (Pre-Shared Key) to be used for authentication of a communicating device. Can contain up to 32 characters.

Key Perfect Forward Secrecy

Select whether to enable or disable PFS (Perfect Forward Secrecy).