[07: Finishing: Finisher]

Adjust the horizontal position of the punch holes when using Finisher SR5090 or Booklet Finisher SR5100.

Press [+] to move the position toward the top edge (left) relative to the paper feed direction, or [−] to move it toward the bottom edge (right).

Adjust the vertical position of the punch holes when using Finisher SR5090 or Booklet Finisher SR5100.

Press [+] to move the position forward (up), or [−] to move it backward (down).

Adjust the vertical position of the staples when using Finisher SR5090 or Booklet Finisher SR5100.

Press [+] to move the position forward (up), or [−] to move it backward (down).

Adjust the horizontal position of the booklet staples when using Booklet Finisher SR5100.

Press [+] to move the position to the right (across horizontally-spreading pages), or press [−] to move it to the left.

Adjust the horizontal position of the folding when using Booklet Finisher SR5100.

Press [+] to move the position to the right (across horizontally-spreading pages), or press [−] to move it to the left.

Adjust the speed of center folding by Booklet Finisher SR5100. By reducing the folding speed, you can make folds crisper.

Adjust the amount of skew correction for punching in order to reduce punch skew due to difference in size, thickness, and curl of paper, when using Finisher SR5090 or Booklet Finisher SR5100.

If the sheets become skewed as a result of punching, press [+] to increase the degree of skew correction.

Disable punch skew correction if jams or edge-folding problems occur particularly when punching lightweight paper using Finisher SR5090 or Booklet Finisher SR5100.

Adjust the width of the paper alignment jogger in the shift tray in order to reduce vertical variation in paper alignment due to difference in size, thickness, and paper curl when using Finisher SR5090 or Booklet Finisher SR5100.

Press [+] to make the width of the paper alignment jogger wider, or [−] to make narrower.

Adjust the width of the staple jogger for edge stapling in order to reduce vertical variation in paper alignment due to difference in size, thickness, and paper curl when using Finisher SR5090 or Booklet Finisher SR5100.

Press [+] to make the width of the staple jogger wider, or [−] to make narrower.

Adjust the width of the staple jogger for booklets in order to reduce vertical variation in paper alignment due to difference in size, thickness, and paper curl when using Booklet Finisher SR5100.

Press [+] to make the width of the staple jogger wider, or [−] to make narrower.

Adjust the paper tapping for extra paper feed to the paper guide for stapling.

Adjust this setting if the paper delivered to the paper guide for stapling overshoots or stops short of the guide.

Adjust the paper alignment in the paper feed direction for center folding.

Adjust this setting if the paper alignment in the paper feed direction is inaccurate because of inconsistent paper size and paper curling when using certain types of paper.

Specify the number of sheets the staple unit aligns at a time for stapling.

Depending on the type of paper, if too many sheets are sent to the staple unit at a time, they may not be aligned properly. If this happens, reduce the number of sheets. However, doing this will increase the time it takes to align the sheets and may reduce throughput.

Set no. of sheets to align for booklet at one time.

Adjust it when sheets are not aligned due to type, condition or no. of sheets.

When no. is less, it takes more time and productivity is low.

This function can be used with Booklet Finisher SR5100.

Adjust the vertical position of the staple (applied at an edge) when using Finisher SR5110 or Booklet Finisher SR5120.

Press [+] to move the stapling position away from the side edge of the sheet or [−] to move it toward the edge.

Adjust the vertical position of the staples (dual) when using Finisher SR5110 or Booklet Finisher SR5120

Press [+] to move the two stapling positions away from the center and each other or [−] to move them toward each other.

Adjust the horizontal position of the staples when using Finisher SR5110 or Booklet Finisher SR5120.

Press [+] to move the stapling position away from the trailing edge of the sheet or [−] to move it toward the edge.

Adjust the width of the staple jogger 1/2 for edge stapling when using Finisher SR5110 or Booklet Finisher SR5120.

Use this to reduce the vertical variation in paper alignment due to differing size, thickness, or paper curl.

Press [+] to make the width of the staple jogger wider, or [−] to make narrower.

Adjust the width of the Staple Jogger to reduce the dispersion of paper orientation in right angle for each paper weight. Use [+] or [-] to expand or reduce the width.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Adjust the width of the Staple Jogger to reduce the dispersion of paper orientation in right angle for each paper weight. Use [+] or [-] to expand or reduce the width.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Adjust the travel distance of the paper edge stopper for edge stapling in order to reduce horizontal variation in paper alignment due to difference in size, thickness, and paper curl when using Finisher SR5110 or Booklet Finisher SR5120.

Press [+] to increase the travel distance, or [−] to decrease.

Adjust Tip Stopper movement when using Edge Stapling. It reduces diversion of paper alignment in horizontal direction for each paper weight. Use [+] or [-] to increase or decrease movement.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Adjust Tip Stopper movement when using Edge Stapling. It reduces diversion of paper alignment in horizontal direction for each paper weight. Use [+] or [-] to increase or decrease movement.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Specify the number of sheets the staple unit aligns at a time for stapling.

Depending on the type of paper, if too many sheets are sent to the staple unit at a time, they may not be aligned properly. If this happens, reduce the number of sheets. However, doing this will increase the time it takes to align the sheets and may reduce throughput.

Adjust the vertical position of the punch holes when using Finisher SR5110 or Booklet Finisher SR5120.

Press [+] to move the position forward (up), or [−] to move it backward (down).

Adjust the horizontal position of the punch holes when using Finisher SR5110 or Booklet Finisher SR5120.

Press [+] to move the position toward the top edge (left) relative to the paper feed direction, or [−] to move it toward the bottom edge (right).

Specify whether or not to enable punch skew correction when using Finisher SR5110 or Booklet Finisher SR5120.

If jams or edge-folding problems occur particularly when punching lightweight paper, select [Off].

Adjust the amount of skew correction for punching when using Finisher SR5110 or Booklet Finisher SR5120.

If the sheets become skewed as a result of punching, press [+] to increase the degree of skew correction.

Specify the accuracy of printed paper alignment when applying shift-sorting with Finisher SR5110 or Booklet Finisher SR5120.

Use this if the tops of the sheets stacked by shift-sorting are misaligned.

If [Speed Priority (Normal)] is selected, the shifting speed is reduced by approximately half to reduce them is alignment at the top due to inertia when the tray is moved.

Set the alignment precision of output sheets during Shift Sorting. Select [Accuracy Priority] to reduce the skew.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Set the alignment precision of output sheets to reduce the curl of thin paper ejected on the Shift Tray. Select [Accuracy Priority] to reduce the curl.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Adjust the width of the paper alignment jogger in the shift tray in order to reduce vertical variation in paper alignment due to difference in size, thickness, and paper curl when using Finisher SR5110 or Booklet Finisher SR5120.

Press [+] to make the width of the paper alignment jogger wider, or [−] to make narrower.

Specify the descending position for the finisher shift tray when paper is delivered to it using Finisher SR5110 or Booklet Finisher SR5120.

The finisher shift tray descends when a deck of stapled paper is delivered to it. However, if its descending position is misaligned, the paper may not be delivered or stacked properly. Select the descending position according to the thickness of the paper in use.

Specify whether or not to press down the trailing edge of the paper when it is delivered to the finisher shift tray of Finisher SR5110 or Booklet Finisher SR5120.

Depending on the type of paper, if too many sheets are sent to the shift tray at a time, they may not be aligned properly.

To reduce variations in paper alignment, set this to [On].

Specify how the shift tray fan moves when using Finisher SR5110 or Booklet Finisher SR5120.

To separate sheets stuck together, blow air to them that are delivered to the shift tray.

Adjust the airflow of the shift tray for fanning the sheets when using Finisher SR5110 or Booklet Finisher SR5120.

If sheets to the shift tray are stuck to each other when this setting is at its default value, increase the fan capacity.

Adjust the horizontal position of the booklet staples when using Booklet Finisher SR5120.

Press [+] to move the position left, or press [−] to move it right on the open booklet.

Adjust the horizontal position of the folding when using Booklet Finisher SR5120.

Press [+] to move the position left, or press [−] to move it right on the open booklet.

Adjust the width of the staple jogger for booklets in order to reduce vertical variation in paper alignment due to difference in size, thickness, and paper curl when using Booklet Finisher SR5120.

Press [+] to make the width of the staple jogger wider, or [−] to make narrower.

Specify the number of booklet folds to be performed when using Booklet Finisher SR5120.

You can adjust the paper folding strength by changing the number of folds per the booklet.

When you select "0", the default value, the finisher folds the booklet according to the number of sheets in the booklet, as shown below.

The value set here is added to the default values, which are 1, 2, and 3. Set a negative value to reduce the number of times the finisher folds booklets. Set -1, -2, or -3 to not fold booklets that have 1 to 13 sheets, 7 to 10 sheets, or 11 to 30 sheets, respectively.

Adjust the travel distance of the paper edge stopper for booklets in order to reduce horizontal variation in paper alignment due to difference in size, thickness, and paper curl when using Booklet Finisher SR5120.

Press [+] to increase the travel distance, or [−] to decrease.

Adjust feed amount of the folding roller for a booklet.

This function can be used with Booklet Finisher SR5120.

Set the convert number of sheets for a booklet.

This function can be used with Booklet Finisher SR5120.

Specify how to correct skew (occurring during paper transport) when Z-folding with the folding unit.

If [Off] is selected, skew is not corrected.

If [On] is selected, skew is corrected by bringing the sheets flush against a guide.

If [On (Reverse)] is selected, skew is corrected by bringing the sheets flush against a guide while the registration roller rotates in reverse to prevent the Z-folded sheets from passing through the registration roller.

Adjust the length of sheets moved for Z-fold skew correction.

Use this if the Z-fold skew correction causes problems.

With the factory default setting of "0", the length of the sheets moved is set to 9 mm. Press [−] to reduce the length. With "9", the length of sheets moved for Z-fold skew correction is reduced to "0".

Adjust how much the registration roller rotates in reverse for Z-fold skew correction.

Use this if the Z-fold skew correction causes problems.

With the initial factory setting of "0", the reverse rotation is set to 3 mm. By pressing [−], you can reduce the reverse rotation down to "0".

Specify the amount of paper stacked in Finisher SR5110 or Booklet Finisher SR5120.

Specify the amount of paper that can be stacked in the shift tray to avoid jamming (depends on the paper size).

Set the proper number of sheets for each paper size to stack on the shift tray at the time of shift sorting.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Set the proper number of envelopes for each envelope size to stack on the shift tray.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Set the accuracy priority for stapling.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Set the accuracy priority for a booklet.

This function can be used with Booklet Finisher SR5120.

Set the operation when the Paper Strengthening Rib is installed to Staple Tray.

This function can be used with Finisher SR5110 or Booklet Finisher SR5120.

Before you set [Staple Tray: Rib Installed Mode to Strengthen Paper] to [On], attach the paper strengthening ribs.

Adjust the paper alignment gap for stapling.

Adjust this if paper is misaligned because of the type, or number of sheets of paper.

Adjust the angle of the paper alignment jogger of the shift tray when attaching the support tray.

Select [+] to lower the jogger position for paper alignment and [-] to raise it.

Specify this setting if roller stains or paper jams occur when delivering punched paper.

If set to [On], paper jams are but throughput may be reduced.