Loading Paper into the Paper Tray
The method of loading paper varies for each tray type.
- When replacing paper or removing jammed paper, make sure not to trap or injure your fingers.
- If the first layer paper tray is installed, do not pull out more than one tray at a time. Pressing down forcefully on the machine's upper surface might cause the machine topple over, possibly resulting in injury.
Before loading paper into a tray, check the paper size and type that can be loaded in the tray.
To load thick paper or other special paper, specify the paper type or thickness in [Tray/Paper Settings] of [Settings].
Check the paper setting before printing. If the paper differs from the paper setting, a mismatch error will occur when you print.
Straighten curled or warped paper before loading.
If a paper tray is pushed vigorously when putting it back into place, the position of the tray's side fences may slip out of place.
When loading a low number of sheets, be sure not to squeeze the side fences in too tightly. If the side fences are squeezed too tightly against the paper, the edges may crease or the paper may misfeed.
When loading paper on a tray which has a few sheets of paper, multiple sheets of paper may be fed at once from the tray. Take out all sheets, fan the sheets, and then load them again.
You may hear the sound of rubbing paper. This is not a malfunction.
If the cut side of the paper is not flat, curls will occur on the edge. This curl is called a burr. If double-feed occurs when you set the paper with burrs, set the burred side faced down.
If a paper jam occurs when you set the paper with burrs, set the burred side facing up.
If double-feed or paper jams still occur, set the burred side upside down.
Loading Paper into Tray 1
Slide the side fences until they are aligned with the sides of the paper. If there is space between the side fences and the paper, it may cause the image to be misaligned.
Check that paper in the paper tray is not being used, and then pull the tray carefully out until it stops.
Remove paper if loaded.
While pressing down the release lever of the side fence, slide the side fences outward.
While pinching the release lever of the end fence, slide the end fence outward.
IM C300 series
IM C400 series
Rotate the fixing screw of the stopper 90 degrees counterclockwise with a coin or similar object and remove the stopper.
Square the paper and load it print side up.
Do not stack paper over the limit mark.
IM C300 series
IM C400 series
Align the end and side fences gently against the paper you loaded.
Make sure that there is no space between the paper and the side fences or end fence.
IM C300 series
IM C400 series
To fix the end fence, engage the two projections of the stopper with the holes on the end fence, and then tighten the fixing screw by rotating it 90 degrees clockwise with a coin or similar object.
If you will not fix the end fence, put the stopper in the position as shown in the illustration, and then rotate the fixing screw 90 degrees clockwise with a coin or similar object.
Carefully slide the paper tray fully in.
Loading Paper into Tray 2 to 4
The paper size setting is changed in the same way for each paper tray.
In the following example procedure, the paper size setting for tray 2 is changed.
Slide the side fences until they are aligned with the sides of the paper, and then re-lock the side fences. If there is space between the side fences and the paper, it may cause the image to be misaligned.
Check that paper in the paper tray is not being used, and then pull the tray carefully out until it stops.
Remove paper if loaded.
Release the lock on the side fence.
While pressing down the release lever of the side fence, slide the side fences outward.
While pinching the release lever of the end fence, slide the end fence outward.
Square the paper and load it print side up.
Do not stack paper over the limit mark. If you load paper over the limit mark, the printed images may become slanted or a paper jam may occur.
Align the back and side fences gently against the paper you loaded.
Re-lock the side fences.
Carefully slide the paper tray fully in.
Loading Paper into the Bypass Tray
Use the bypass tray to load paper of a size that cannot be loaded into Tray 1 to 4, such as transparency film and label paper (adhesive labels).
The maximum number of sheets you can load into the bypass tray depends on the paper type.
Recommended Paper Sizes and Types
Do not stack paper over the limit mark. If you load paper over the limit mark, the print image may be slanted or the paper may be jammed.
Open the bypass tray.
When loading paper larger than A4 or 81/2 × 11 size, pull out the extender.
Load the paper with the print side down, and push it in lightly until you hear a beep.
Fan sheets before loading so that multiple sheets of paper do not stick to each other and are not fed at once.
When loading envelopes or letterhead paper, confirm the orientation, face and back, or location of flaps.
Align the paper guides to the paper size.
To load paper on the bypass tray, it is better to orient it in the direction of
.You can change the beeper setting under [Touch/Notification Sound] in [Settings]
[System Settings][Sound].
Specifying Regular Sizes Using the Control Panel
Press [Settings] on the Home screen.
Press [Tray/Paper Settings].
Press [Paper Size/Paper Type].
Press one tray to set.
Press [Paper Size].
To specify for the bypass tray, press [Paper Size: Printer].
Choose one paper size from the list shown, and then press [OK].
Press [OK].
After completing the configuration, press [Home] (
).
Specifying a Custom Size Paper Using the Control Panel
Press [Settings] on the Home screen.
Press [Tray/Paper Settings].
Press [Paper Size/Paper Type].
Press one tray to set.
Press [Paper Size].
To specify for the bypass tray, press [Paper Size: Printer].
Press [Custom] from the list shown.
Press the button to the right of "A" or "B".
Specify the values within the numbers of "< >", and then press [Done].
Press [OK] three times.
After completing the configuration, press [Home] ().
Specifying Paper Type and Thickness Settings
If the print settings and the loaded paper that are used for a print job do not match, a mismatch error occurs.
Check and specify the paper settings before you start printing.
Before you change the settings, confirm the priority of the paper settings for printing (priority to the printer driver or to the control panel).
On the printer driver
Check the settings of paper tray and paper type on the printer driver and make sure the settings match the loaded paper.
On the control panel
Press [Settings] on the Home screen.
Press [Tray/Paper Settings].
Press [Paper Size/Paper Type].
Press one tray to set.
Press [Paper Type/Thickness].
Choose one paper type and paper thickness from the list shown, and then press [OK].
Press [OK].
After completing the configuration, press [Home] ().