User GuideIM 550/600 series

Configuring the IP Address and Other Settings of the Device Server Option

On the control panel of the machine, specify the network information on the device server option to connect to a server on a network segment separate from the network on the mainframe at the same time.

Illustration of Expanded USB Print Server Unit

Configuring the Settings of the Device Server Option (Settings Screen Type: Standard)

1On the Home screen, press [Settings].

Operation panel screen illustration

2Press [System Settings].

Operation panel screen illustration

3Press [Network/Interface][Optional Network].

4Change the network settings.

When you change the setting of [Machine IPv4 Address] to [Auto-Obtain (DHCP)], the machine obtains the IP address from the DHCP server automatically.

When specifying the settings for the network manually, the setting items and default values are as described below.

Specify them according to the network environment.

  • Machine IPv4 Address: Specify/192.168.100.100

    • Subnet Mask: 255.255.255.0

  • IPv4 Gateway Address: 0.0.0.0

  • IPv6 Stateless Address Autoconfiguration: Active

  • DHCPv6 Configuration: Inactive

  • Effective Protocol

    • IPv4: Active

    • IPv6: Inactive

  • Ethernet Speed: Auto Select

  • WINS Configuration: On (Primary WINS Server: 0.0.0.0, Secondary WINS Server: 0.0.0.0, Scope ID)

  • Host Name

5After completing the configuration, press [Home] (Operation panel screen illustration).

Note

  • To print via the device server option, specify the IP address set with the procedure above to install the printer driver.

  • You can specify the delivery destination for jobs executed from the enhanced print server. This function is available on machines implemented with RICOH Always Current Technology v1.2 or later. (IM 600SRF only)

  • Output Tray

Configuring the Settings of the Device Server Option (Settings Screen Type: Classic)

1On the Home screen, press [Settings].

Operation panel screen illustration

2Press [Machine Features Settings].

3Press [System Settings][Interface Settings] tab [Optional Network].

4Change the network settings.

Operation panel screen illustration

When you change the setting of [Machine IPv4 Address] to [Auto-Obtain (DHCP)], the machine obtains the IP address from the DHCP server automatically.

When specifying the settings for the network manually, the setting items and default values are as described below.

Specify them according to the network environment.

  • Machine IPv4 Address: Specify/192.168.100.100

    • Subnet Mask: 255.255.255.0

  • IPv4 Gateway Address: 0.0.0.0

  • IPv6 Stateless Address Autoconfiguration: Active

  • DHCPv6 Configuration: Inactive

  • Effective Protocol

    • IPv4: Active

    • IPv6: Inactive

  • Ethernet Speed: Auto Select

  • WINS Configuration: On (Primary WINS Server: 0.0.0.0, Secondary WINS Server: 0.0.0.0, Scope ID)

  • Host Name

5After completing the configuration, press [Home] (Operation panel screen illustration).

Note

  • To print via the device server option, specify the IP address set with the procedure above to install the printer driver.

  • You can specify the delivery destination for jobs executed from the enhanced print server. This function is available on machines implemented with RICOH Always Current Technology v1.2 or later. (IM 600SRF only)

  • Output Tray

  • If you forget the IP address of the device server option or cannot connect the machine to the network, restore the factory default settings by following the procedure below.

    1. Turn the main power switch of the machine off.

    2. While pressing the switch on the device server option with the tip of a pen, turn the main power switch of the machine on.

      Keep the switch held down until Step 4 is completed.

      Illustration of Expanded USB Print Server Unit
    3. Confirm that the top and bottom LEDs of the Ethernet port light.

    4. When the top LED turns off and the bottom LED lights in yellow, release the switch on the device server option.