Skip header
 

Setting Items of IEEE 802.1X for Wireless LAN

1Log in as the network administrator from Web Image Monitor.

2Point to [Device Management], and then click [Configuration].

3Click [IEEE 802.1X] under "Security".

4In "User Name", enter the user name set in the RADIUS server.

5Enter the domain name in "Domain Name".

6Select "EAP Type". Configurations differ according to the EAP Type.

EAP-TLS

  • Make the following settings according to the operating system you are using:

    • Select [On] or [Off] in "Authenticate Server Certificate".

    • Select [On] or [Off] in "Trust Intermediate Certificate Authority".

    • Enter the host name of the RADIUS server on "Server ID".

    • Select [On] or [Off] in "Permit Sub-domain".

LEAP

  • Click [Change] in "Password", and then enter the password set in the RADIUS server.

EAP-TTLS

  • Click [Change] in "Password", and then enter the password set in the RADIUS server.

  • Click [Change] in "Phase 2 User Name", and then enter the user name set in the RADIUS server.

  • Select [CHAP], [MSCHAP], [MSCHAPv2], [PAP], or [MD5] in "Phase 2 Method".

    Certain methods might not be available, depending on the RADIUS server you want to use.

  • Make the following settings according to the operating system you are using:

    • Select [On] or [Off] in "Authenticate Server Certificate".

    • Select [On] or [Off] in "Trust Intermediate Certificate Authority".

    • Enter the host name of the RADIUS server in "Server ID".

    • Select [On] or [Off] in "Permit Sub-domain".

PEAP

  • Click [Change] in "Password", and then enter the password set in the RADIUS server.

    If [TLS] is selected for "Phase 2 Method", you do not need to specify a password.

  • Click [Change] on "Phase 2 User Name", and then enter the user name set in the RADIUS server.

  • Select [MSCHAPv2] or [TLS] in "Phase 2 Method".

    When you select [TLS], you must install "IEEE 802.1X Client Certificate".

  • Make the following settings according to the operating system you are using:

    • Select [On] or [Off] in "Authenticate Server Certificate".

    • Select [On] or [Off] in "Trust Intermediate Certificate Authority".

    • Enter the host name of the RADIUS server on "Server ID".

    • Select [On] or [Off] in "Permit Sub-domain".

7Click [OK].

8“Updating...” appears. Wait for about 1 or 2 minutes, and then click [OK].

If the previous screen does not appear again after you click [OK], wait for a while, and then click the web browser's refresh button.

9Click [Wireless LAN Settings] under "Interface".

10Select [Wireless LAN] in "LAN Type".

11Select [Infrastructure Mode] in "Communication Mode".

12Enter the alphanumeric characters (a-z, A-Z, or 0-9) in [SSID] according to the access point you want to use.

13Select [WPA2] in "Security Method".

14Select [WPA2] in "WPA2 Authentication Method".

15Click [OK].

16“Updating...” appears. Wait for about 1 or 2 minutes, and then click [OK].

If the previous screen does not appear again after you click [OK], wait for a while, and then click the web browser's refresh button.

17Log out.

Note

  • If there is a problem with settings, you might not be able to communicate with the machine. In such a case, access [Print List] in [Interface Settings] on the control panel, and then print the network summary to check the status.

  • If you cannot identify the problem, execute [Restore IEEE 802.1X Authentication to Defaults] in [Network] in [Interface Settings] on the control panel, and then repeat the procedure.