Input / Output

You can select to have Batch mode or SADF mode displayed when you press [Original Settings].

Default: [Batch]

In SADF mode, an original must be placed within a specified time after the previous original has been fed.

Default: [5 second(s)]

You can adjust this time from 3 to 99 seconds in increments of 1 second.

Specify whether or not the machine continues copying when paper of the required orientation runs out during rotate sort.

Default: [Off]

• On

  Copying continues using copy paper of a different orientation. The copy job will finish even if you have left the machine.

• Off

  When paper of the required orientation runs out, the machine stops copying and prompts you to supply copy paper. After you have loaded paper, the machine will continue copying.

When memory becomes full while scanning originals, the machine can make copies of scanned originals first, and then automatically proceed scanning remaining originals.

Default: [Off]

• On

  You can leave the machine unattended to make copies, but sorted pages will not be sequential.

• Off

  When memory becomes full, the machine stops operation allowing you to remove the copy pages delivered on the output tray.

If you select [Yes] in this function, the machine rotates the image correctly.

Default: [No]

Orientation-fixed (top to bottom) or two-sided paper might not be printed correctly depending on how the originals and paper are placed. For details, see "Loading Orientation-fixed Paper or Two-sided Paper", Paper Specifications and Adding Paper.

Specify whether or not to display the staple-free staple button on the initial screen when Finisher SR3210 is installed.

When you select [Stapleless Stapler], the staple-free staple button is displayed.

Default: [Stapleless Stapler]

Specify which staple type has priority to be shown on the initial screen.

• When Internal Finisher SR3130 is installed:

  Default for "Staple Position 1": [Staple: Top 1]

  Default for "Staple Position 2": [Staple: Bottom 1]

  Default for "Staple Position 3": [Staple: Left 2]

  Default for "Staple Position 4": [Staple: Top 2]

• When Finisher SR3210 is installed:

  Default for "Staple Position 1": [Staple: Top 1]

  Default for "Staple Position 2": [Staple: Left 2]

  Default for "Staple Position 3": [Staple: Top 2]

• When Booklet Finisher SR3220 is installed:

  Default for "Staple Position 1": [Staple: Top 1]

  Default for "Staple Position 2": [Staple: Center]

  Default for "Staple Position 3": [Staple: Left 2]

  Default for "Staple Position 4": [Staple: Top 2]

• When Finisher SR3230 is installed:

  Default for "Staple Position 1": [Staple: Slant]

  Default for "Staple Position 2": [Staple: Bottom 1]

  Default for "Staple Position 3": [Staple: Left 2]

  Default for "Staple Position 4": [Staple: Top 2]

• When Booklet Finisher SR3240 is installed:

  Default for "Staple Position 1": [Staple: Slant]

  Default for "Staple Position 2": [Staple: Center]

  Default for "Staple Position 3": [Staple: Left 2]

  Default for "Staple Position 4": [Staple: Top 2]

• When Internal Finisher SR3180 is installed:

  Default for "Staple Position 1": [Staple: Slant]

  Default for "Staple Position 2": [Off]

  Default for "Staple Position 3": [Off]

  Default for "Staple Position 4": [Off]

Specify which punch type has priority to be shown on the initial screen.

• When 2 & 4 hole punch unit is installed:

  Default for "Punch Type 1": [Punch: 2 Holes Left]

  Default for "Punch Type 2": [Punch: 2 Holes Top]

• When 2 & 3 hole punch unit is installed:

  Default for "Punch Type 1": [Punch: 3 Holes Left]

  Default for "Punch Type 2": [Punch: 3 Holes Top]

You can select which key is displayed with higher priority for "Finishing Types" on the simple screen.

Default for "Simplified Screen: Finishing Types 1": [Do not Display]

Default for "Simplified Screen: Finishing Types 2": [Do not Display]

Default for "Simplified Screen: Finishing Types 3": [Do not Display]