Unpacking

To protect it from shock and vibration during transit, this machine comes packaged in cushioning foam and secured with tape. Remove these protective materials after bringing the machine to where it will be installed.

Be sure to locate the machine as close as possible to a wall outlet. This will allow easy disconnection of the power cord in the event of an emergency.

If the machine emits smoke or odours, or if it behaves unusually, you must turn off its power immediately. After turning off the power, be sure to disconnect the power cord plug from the wall outlet. Then contact your service representative and report the problem. Do not use the machine. Doing so could result in fire or electric shock.

If metal objects, or water or other fluids fall inside this machine, you must turn off its power immediately. After turning off the power, be sure to disconnect the power cord plug from the wall outlet. Then contact your service representative and report the problem. Do not use the machine. Doing so could result in fire or electric shock.

Do not touch this machine if a lightning strike occurs in the immediate vicinity. Doing so could result in electric shock.

Keep the polythene materials (bags, gloves, etc.) supplied with this machine away from babies and small children at all times. Suffocation can result if polythene materials are brought into contact with the mouth or nose.

Do not incinerate toner (new or used) or toner containers. Doing so risks burns. Toner will ignite on contact with naked flame.

Do not store toner (new or used) or toner containers anywhere near naked flames. Doing so risks fire and burns. Toner will ignite on contact with naked flame.

Do not crush or squeeze toner containers. Doing so can cause toner spillage, possibly resulting in dirtying of skin, clothing, and floor, and accidental ingestion.

Store toner (new or used), toner containers, and components that have been in contact with toner out of reach of children.

If toner or used toner is inhaled, gargle with plenty of water and move into a fresh air environment. Consult a doctor if necessary.

If toner or used toner gets into your eyes, flush immediately with large amounts of water. Consult a doctor if necessary.

If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor if necessary.

When moving the machine, use the inset grips on both sides. The machine will break or cause injury if dropped.

Do not look into the lamp. It can damage your eyes.

During operation, rollers for transporting the paper and originals revolve. A safety device has been installed so that the machine can be operated safety. But take care not to touch the machine during operation. Otherwise, an injury might occur.

Removed tape is dirty. Be careful not to let it touch your hands or clothes.
Leave the protective materials in place while moving the machine.
Lower the machine slowly and carefully to prevent trapping your hands.
Do not grip on the tray area when lifting the machine.
Do not allow paper clips, staples, or other small objects to fall inside the machine.
Keep uncovered print cartridges away from direct sunlight.
Do not touch the print cartridge's photo conductor unit.
Do not touch the ID chip on the side of the print cartridge as indicated in the illustration below.

Remove the plastic bag.
Lift the machine with another person using the inset grips on both sides of the machine.
Remove the protective materials attached on the machine's exterior. Do not remove tapes going into the inside of the machine.
The actual machine may come with protective materials attached in different positions. Make sure to check the machine's exterior for all protective materials, and remove them completely.
Open the ADF cover.
Move the lever slightly to the machine rear, and then pull it up to unlock the paper feed roller.
Lift the paper feed roller slightly to remove it.
Pull the protective sheet to remove it.
With the roller part facing downwards, insert the tip of the paper feed roller into the opening of the ADF.
Return the paper feed roller to its original position.
Lower the lever until it clicks into place.
Close the ADF cover.
Pull the opening lever on the front cover, and then carefully lower the front cover.
Pull the tapes gently upward and remove them from the machine at the same time.
Pull up the fusing unit levers.
Using both hands, carefully push up the front cover until it closes.
Pull up the top cover open lever, and then open the top cover carefully.
Make sure that the ADF is closed.
Remove the protection tapes.
Lift out print cartridges and shake them from side to side. The black print cartridge comes with a protection sheet that you must remove before shaking.
Carefully lift out the print cartridge vertically, holding its center.
Place the black print cartridge on a flat surface and remove the protection sheet before shaking.
Shake each print cartridge from side to side five or six times.
Check the toner color and corresponding location, and then carefully insert the print cartridge vertically.
Using both hands, hold the center of the top cover and close the cover carefully. Be careful not to trap your fingers.
Apply the indicated sticker as in the illustration below.