Skip header
 

When You Have Problems Operating the Machine

This section describes common problems and messages. If other messages appear, follow the instructions displayed.

Problem

Causes

Solutions

Although the copier screen appears when the machine is turned on using the main power switch, it cannot be switched to another screen by pressing the [Printer] or [Scanner] key.

Functions other than the copier function are not yet ready.

Wait a little longer.

The machine has just been turned on and the User Tools screen is displayed, but the User Tools menu has items missing.

Functions other than the copier function are not yet ready. Time required varies by function. Functions appear in the User Tools menu when they become ready for use.

Wait a little longer.

The operation switch indicator continues blinking and does not turn off when pressed.

This occurs in the following cases:

  • The exposure glass cover or ADF is open.

  • The machine is communicating with external equipment.

  • The hard disk is active.

  • Close the exposure glass cover or ADF.

  • Check if the machine is communicating with external equipment.

  • Wait a little longer.

The display is off.

The machine is in Energy Saver mode.

Press the [Energy Saver] key to cancel Energy Saver mode.

The display is off.

The operation switch is turned off.

Turn on the operation switch.

Nothing happens when the operation switch is turned on.

The main power switch is turned off.

Turn on the main power switch.

"Please wait." appears.

This message appears when you turn on the operation switch.

Wait for a while. If the machine does not get ready in two minutes, contact your service representative.

“Please wait.” appears.

This message appears when the machine is warming up.

  • Wait for a while. If the machine does not get ready in two minutes, contact your service representative.

  • Wait until the message disappears. Do not turn off the main power switch while the message is showing.

“Please wait.” appears.

This message appears when you change the toner cartridge.

Wait for a while. If the message does not disappear in two minutes, contact your service representative.

“Memory is full. Do you want to store scanned file?” appears.

The scanned originals exceed the number of sheets/pages that can be stored on the hard disk.

  • Press [Yes] to store pages that have been scanned. Delete unnecessary files by pressing [Delete File].

  • Press [No] if you are not storing pages that have been scanned. Delete unnecessary files by pressing [Delete File].

“Self checking...” appears.

The machine is performing image adjustment operations.

The machine may perform periodic maintenance during operations. The frequency and duration of maintenance depends on the humidity, temperature, and printing factors such as number of prints, paper size, and paper type. Wait for the machine to get ready.

The user code entry screen is displayed.

Users are restricted by User Code Authentication.

Enter the user code (up to eight digits), and then press [OK].

The Authentication screen appears.

Basic Authentication, Windows Authentication, LDAP Authentication or Integration Server Authentication is set.

Enter your login user name and user password. See "When the Authentication Screen is Displayed", About This Machine.

“Authentication has failed.” appears.

The entered login user name or login password is not correct.

Ask the user administrator for the correct login user name and login password.

“Authentication has failed.” appears.

The machine cannot perform authentication.

Contact your administrator.

“You do not have the privileges to use this function.” continues to be displayed even though you have entered a valid user name.

The logged in user name does not have permission for the selected function.

Contact your administrator about the permission for the required function.

An error message remains, even if misfed paper is removed.

  • When a misfeed message appears, it remains until you open and close the cover as required.

  • Paper is still jammed in the tray.

Remove misfed paper, and then open and close the cover. See Removing Jammed Paper.

Original images are printed on the reverse side of the paper.

You may have loaded the paper incorrectly.

Load paper correctly. Load paper into the paper tray or LCT with the print side up. Load paper into bypass tray with the print side down.

Misfeeds occur frequently.

The tray's side or end fences may not be set properly.

  • Remove misfed paper. See Removing Jammed Paper.

  • Check that the side or end fences are set properly. Also, check that the side fences are locked. See "Changing the Paper Size", About This Machine.

Misfeeds occur frequently.

Paper of undetectable size has been loaded.

  • Remove misfed paper. See Removing Jammed Paper.

  • If you load a paper size that is not selected automatically, you need to specify the paper size with the control panel. See "Changing to a Size That Is Not Automatically Detected", About This Machine.

Misfeeds occur frequently.

There is a foreign object on the finisher shift tray.

  • Remove misfed paper. See Removing Jammed Paper.

  • Do not place anything on the finisher shift tray. It may cause a paper jam.

Cannot print in duplex mode.

"Apply Duplex" is set to [No] for "Paper Type".

Under "Paper Type" in [Tray Paper Settings], set "Apply Duplex" to [Yes]. For details, see "Tray Paper Settings", Network and System Settings ReferenceIllustration indicating instructions stored on a CD-ROM.

Cannot print in duplex mode.

You have selected a paper type that cannot be used for duplex print.

In [Tray Paper Settings], select a paper type that can be used for duplex print. For details about the paper types that can be used, see "Duplex Copying", Copy and Document Server ReferenceIllustration indicating instructions stored on a CD-ROM.

“Following output tray is full. Remove paper.” appears.

The output tray is full.

Remove paper from the output tray to resume printing.

"Turn main Power Switch off" appears.

The machine does not shut down normally when the main power switch is turned off, and then immediately turned on.

Turn off the machine. Wait for three seconds or more after shutting it down, and then turn it on again.

“Shutting down... Please wait. Main power will be turned off automatically.” appears.

The shut down procedure has begun because the main power switch was turned off while the machine was in standby mode or performing an operation.

Follow the message that appears and wait until the machine has shut down. Do not turn on the main power switch while this message is displayed. If the main power switch has been turned on, follow the message that appears. For details about turning the main power switch on and off, see "Turning On/Off the Power", About This Machine.

An error has occurred when the Address Book is changed from the display panel or Web Image Monitor.

The Address Book cannot be changed while deleting the multiple stored documents.

Wait a while, and then retry the operation.

Cannot use Web Image Monitor to print documents stored in Document Server.

When print volume limits are specified, users cannot print beyond their print volume limit. Print jobs selected by users who have reached their print volume limits will be canceled.

  • For details about specifying print volume limits, contact your administrator.

  • To view the status of a print job, see [Print Job History]. In Web Image Monitor, [Print Job History] is under [Document Server] in [Job].

Note

  • If you cannot make copies as you want because of paper type, paper size, or paper capacity problems, use the recommended paper. See "Recommended Paper Sizes and Types", About This Machine.

  • Using curled paper often causes misfeeds, soiled paper edges, or slipped positions while performing staple or stack printing. When using curled paper, take the stiffness out of the paper with your hands to straighten out the curl, or load the paper up side down. Also, lay paper on a flat surface to prevent paper from curling, and do not lean it against the wall.