Skip header
ManualsContentsPreviousNextHelp

General Settings

Specify basic print settings.

Paper Tray Setting

Select which input tray to use for printing. If you select "Auto Paper Select" the machine automatically selects an input tray based on the paper size and type specified by the job.

Margin Tolerance

Specify an area of allowance for the gap between the print area and the paper size when using "Auto Paper Select".

Output Exit

Specify the output tray for printed paper.

Auto Tray Switching

Enables the machine to switch automatically from an emptied paper tray to another tray that contains the same size, orientation, and type of paper, without interrupting the job.

Paper Type

Select a paper type.

Cut Method

Select the paper cut method. When roll paper is selected for input tray, the cut method is enabled.

  • Preset Cut

    region-a (mainly Europe and Asia)
    Cuts the roll paper to a standard size that fits the width of the sheets that are set in the paper tray.

    Example: If 594 mm wide sheets are set in Tray 1 and 841 mm wide sheets in Tray 2, an image measuring 590 multiplication 840 mm will be printed on a standard size cut sheet measuring 841 multiplication 594 mm Landscape or 594 multiplication 841 mm Portrait. Note that the input tray's settings might change the orientation of the printed sheet.

    region-b (mainly North America)
    Cuts the roll paper to a standard size that fits the width of the sheets that are set in the paper tray.

    Example: If 24 in wide sheets are set in Tray 1 and 36 in wide sheets in Tray 2, an image measuring 23 multiplication 35 in will be printed on a standard size cut sheet measuring 36 multiplication 24 in Landscape or 24 multiplication 36 in Portrait. Note that the input tray's settings might change the orientation of the printed sheet.

    Note

    • If you specify [Auto Paper Select] for [Paper Tray Setting], the roll paper that requires the shortest cut is selected. However, if the print job is an image that exceeds 36 multiplication 48 in, the job is cancel.

    • If you specify the input tray for [Paper Tray Setting], the image area that does not fit inside the standard size is not printed.

  • Synchro Cut

    region-a (mainly Europe and Asia)
    Cuts the roll paper according to the width of the sheets that are set in the paper tray and the length of the image.

    Example: If 594 mm wide sheets are set in Tray 1 and 841 mm wide sheets in Tray 2, an image measuring 590 multiplication 840 mm will be printed on a cut sheet measuring 841 multiplication 590 mm Landscape or 594 multiplication 840 mm Portrait. Note that the input tray's settings might change the orientation of the printed sheet. Use this method to print images that exceed the standard size, such as an 841 multiplication 1220 mm image.

    region-b (mainly North America)
    Cuts the roll paper according to the width of the sheets that are set in the paper tray and the length of the image.

    Example: If 24 in wide sheets are set in Tray 1 and 36 in wide sheets in Tray 2, an image measuring 23 multiplication 35 in will be printed on a cut sheet measuring 36 multiplication 23 in Landscape or 24 multiplication 35 in Portrait. Note that the input tray's settings might change the orientation of the printed sheet. Use this method to print images that exceed the standard size, such as an 36 multiplication 49 in image.

    Note

    • If you specify [Auto Paper Select] for [Paper Tray Setting], the tray with the roll paper that requires the shortest cut is selected.

    • If both the width and length of the data exceed 36 in, sheet's long edge is cut to the maximum 36 in.

    • If you specify the input tray for [Paper Tray Setting], the sheet is cut to the long edge length. If the image exceeds the cut sheet size, the image area that does not fit inside the cut size is not printed.

Reduce / Enlarge

Specify a scaling mode to reduce or enlarge the print size of documents.

Magnification Ratio

Specify the ratio when Magnification Ratio is selected for "Reduce / Enlarge".

Margin Adjustment

Specify the inside margin around the originals. The margin is 0 to 100 mm in 1 mm (0 to 4.00 " in 0.10 ") increments.

Extraction

Specify whether to uncompress and extract compressed job data before printing it. Selecting this option reduces print errors due to corrupted archives, but slows the print process slightly.

Mirror Image

Prints images with left and right reversed.

Positive / Negative

Prints images with black and white inverted.

Dithering

Select a dither pattern appropriate for the print image.

Note

  • If you select [Auto] or [DTP] for this setting, the image is printed using [Photograph].

Original Ratio Fine Adjustment: Horizontal

Adjusts the horizontal size difference between original data and printed image for scaled drawings that must be accurately printed. The ratio range is 99.0 - 101.0%, which you can adjust in increments of 0.01%.

Original Ratio Fine Adjustment: Vertical

Adjusts the vertical size difference between original data and printed image for scaled drawings that must be accurately printed. The ratio range is 99.0 - 101.0%, which you can adjust in increments of 0.01%.

Directional Magnification 1 - Directional Magnification 10

Specify the vertical and horizontal value when Magnification Ratio is selected for "Reduce / Enlarge".