Supplementary Information

You cannot switch between 1-sided and 2-sided originals during copying.

Since small originals may not be correctly aligned with the original guide, the copy image may be slanted.

Copying speed and scanning speed will be reduced.

The weight range for originals in the Mixed Sizes mode is 52 - 81.4 g/m² (13.8 - 21.6 lb).

When using this function with 1 Sided 2 Sided mode, always ensure that the originals of each size are in even numbers. If you have an odd number of originals, insert blank sheets to adjust the total.

The following paper sizes can be selected as the standard sizes:

A3, B4 JIS, A4, B5 JIS, A5, B6 JIS, A6

11 × 17, 8¹/₂ × 14, 8¹/₂ × 13, 8¹/₂ × 11, 8¹/₄ × 14, 8¹/₄ × 13, 8 × 13,

8 × 10¹/₂, 8 × 10, 7¹/₄ × 10¹/₂, 5¹/₂ × 8¹/₂, 12 × 18, 11 × 15, 11 × 14, 10 × 15, 10 × 14

You can select one of 12 preset ratios (5 enlargement ratios, 7 reduction ratios).

Following shows the relation between the original and paper sizes at respective scaling factors.

• Metric version

  400% (Area ratio 16 times): -

  200% (Area ratio 4 times): A5 A3

  141% (Area ratio 2 times): A4 A3, A5 A4

  122%: A4 B4 JIS, 8 × 13 A3

  115%: B4 JIS A3

  93%: -

  82%: B4 JIS A4, 8 × 13 A4

  75%: B4 JIS 8 × 13

  71% (Area ratio ¹/₂ times): A3 A4, A4 A5

  65%: A3 8 × 13

  50% (Area ratio ¹/₄ times): A3 A5, 8 × 13 A5

  25%: -

• Inch version

  400% (Area ratio 16 times): -

  200% (Area ratio 4 times): 5¹/₂ × 8¹/₂ 11 × 17

  155% (Area ratio 2 times): 5¹/₂ × 8¹/₂ 8¹/₂ × 14

  129%: 8¹/₂ × 11 11 × 17

  121%: 8¹/₂ × 14 11 × 17

  93%: -

  85%: 8¹/₂ × 13 8¹/₂ × 11

  78%: 8¹/₂ × 14 8¹/₂ × 11

  73%: 11 × 15 8¹/₂ × 11

  65%: 11 × 17 8¹/₂ × 11

  50% (Area ratio ¹/₄ times): 11 × 17 5¹/₂ × 8¹/₂

  25%: -

You can select a ratio regardless of the size of an original or copy paper. With some ratios, parts of the image might not be copied or margins will appear on copies.

The reproduction ratios you can specify are 25-400%.

You can select a ratio regardless of the size of an original or copy paper. With some ratios, parts of the image might not be copied or margins will appear on copies.

You can place originals of different sizes in the ADF at once.

The machine selects reproduction ratios of between 25-400%.

You can use the following copy paper with this function:

A3, B4 JIS, A4, B5 JIS, A5

11 × 17, 8¹/₂ × 14, 8¹/₂ × 13, 8¹/₂ × 11, 8¹/₄ × 14, 8¹/₄ × 13, 8 × 13, 8 × 10, 7¹/₄ × 10¹/₂, 11 × 15, 10 × 14

You cannot use the following copy paper with this function:

• Paper smaller than A5, 5¹/₂ × 8¹/₂

• Translucent paper

• Label paper (adhesive labels)

• OHP transparencies

• Paper thicker than 169 g/m², 45.5 lb.

• Paper thinner than 60 g/m², 16 lb.

• Postcards

When an odd number of originals are placed in the ADF, the back of the last page of copied paper is blank.

During copying, the image is shifted to allow for the binding margin.

By default, a binding margin is made on the back side.

In this mode, the machine selects the reproduction ratio automatically. This reproduction ratio depends on copy paper sizes and the number of originals.

The reproduction ratios selectable by the machine are 25-400%.

If the calculated ratio is under the minimum ratio, it is automatically adjusted to within available range. However, with some ratios, parts of the image might not be copied.

You cannot use custom size paper.

If the orientation of originals is different from that of the copy paper, the machine will automatically rotate the image by 90° to make copies properly.

If the number of originals placed is less than the number specified for combining, the last page segment is left blank as shown.

Paper sizes and orientations that can be used in the Rotate Sort function are A4, B5 JIS, 8¹/₂ × 11, and 7¹/₄ × 10¹/₂.

The number of copies that can be placed on the tray is as follows. When the number of copies exceeds capacity, remove copies from the tray. (paper weight: 80 g/m², 20 lb.)

• Internal tray 1

  A4, 8¹/₂ × 11 or smaller: 500 sheets (250 sheets when the optional bridge unit is installed.)

  B4 JIS, 8¹/₂ × 14 or larger: 250 sheets (125 sheets when the optional bridge unit is installed.)

• Internal tray 2

  125 sheets

• 1000-sheet finisher (Upper tray)

  A4, 8¹/₂ × 11 or smaller: 250 sheets

  B4 JIS, 8¹/₂ × 14 or larger: 50 sheets

• 1000-sheet finisher (Shift tray)

  A4, 8¹/₂ × 11 or smaller: 1000 sheets

  B4 JIS, 8¹/₂ × 14 or larger: 500 sheets

• 3000-sheet finisher (Upper tray)

  A4, 8¹/₂ × 11 or smaller: 250 sheets

  B4 JIS, 8¹/₂ × 14 or larger: 50 sheets

• 3000-sheet finisher (Shift tray)

  A4, 8¹/₂ × 11: 3000 sheets

  A3, A4, B4 JIS, B5 JIS, 11 × 17, 8¹/₄ × 14, 8¹/₂ × 11, 12 × 18: 1500 sheets

  A5: 500 sheets

  A5, B6 JIS, A6, 5¹/₂ ×8¹/₂: 100 sheets

• Booklet finisher (Upper tray)

  A4, 8¹/₂ × 11 or smaller: 250 sheets

  B4 JIS, 8¹/₂ × 14 or larger: 50 sheets

• Booklet finisher (Shift tray)

  A4, 8¹/₂ × 11: 2000 sheets

  A3, A4, B4 JIS, B5 JIS, 11 × 17, 8¹/₄ × 14, 8¹/₂ × 11, 12 × 18: 1000 sheets

  A5: 500 sheets

  A5, B6 JIS, A6, 5¹/₂ ×8¹/₂: 100 sheets

When using the Rotate Sort or Staple functions, the capacity may be reduced.

Paper sizes and orientations that can be used with the Shift Stack are as follows:

• Booklet finisher/3000-sheet finisher

  A3, B4 JIS, A4, B5 JIS, A5

  11 × 17, 8¹/₂ × 14, 8¹/₂ × 13, 8¹/₂ × 11, 8¹/₄ × 14, 8¹/₄ × 13, 8 × 13, 8 × 10¹/₂, 8 × 10, 7¹/₄ × 10¹/₂, 5¹/₂ × 8¹/₂, 12 × 18, 11 × 15, 11 × 14, 10 × 15, 10 × 14

• 1000-sheet finisher

  A3, B4 JIS, A4, B5 JIS

  11 × 17, 8¹/₂ × 14, 8¹/₂ × 13, 8¹/₂ × 11, 8¹/₄ × 14, 8¹/₄ × 13, 8 × 13, 8 × 10¹/₂, 8 × 10, 7¹/₄ × 10¹/₂, 12 × 18, 11 × 15, 11 × 14, 10 × 15, 10 × 14

The following type of paper cannot be stapled:

• Postcard

• Translucent paper

• OHP transparencies

• Label paper (adhesive labels)

• Thick paper

• Curled paper

• Paper of low stiffness

• Paper of mixed sizes

The 1000-sheet finisher and the booklet finisher do not support the Staple in Mixed Sizes mode. When stapling mixed size originals with the finisher, select Auto Reduce/Enlarge.

You can specify how the machine responds if its memory becomes full during copying, or if the number of copies exceeds the capacity of the stapler:

• Divides the copies into the number of sheets that can be stapled

• Cancels the stapling job

To specify Left 2, Top 2, or Slant together with 2 Originals or 8 Originals of Combine 1 Side, or 4 Originals or 16 Originals of Combine 2 Sides: specify paper for orientation originals and specify paper for orientation originals.

To specify Left 2, Top 2, or Slant together with Double Copies: specify paper for orientation originals and specify paper for orientation originals.

When the booklet finisher or the 3000-sheet finisher is installed, even if you place different size originals in the ADF, appropriate size of copy paper can be automatically selected and stapled using the Mixed Sizes mode and Auto Paper Select function. Load the paper you want to use in the paper trays beforehand. Paper sizes that can be stapled when using the Mixed Sizes mode are as follows:

• A3 and A4

• B4 JIS and B5 JIS

• 11 × 17 and 8¹/₂ × 11

Paper sizes and orientation that can be used in the Staple function and the stapler capacity are as follows: (paper weight: 80 g/m², 20 lb.)

• 1000-sheet finisher

  B4 JIS, 8¹/₂ × 14 or larger: 30 sheets

  A4, 8¹/₂ × 11 or smaller: 50 sheets

• 3000-sheet finisher

  B4 JIS, 8¹/₂ × 14 or larger: 30 sheets

  A4, 8¹/₂ × 11 or smaller: 50 sheets

  In the Mixed Sizes mode: 30 sheets

• Booklet finisher

  B4 JIS, 8¹/₂ × 14 or larger: 30 sheets

  A4, 8¹/₂ × 11 or smaller: 50 sheets

  When stapling center (A3, B4 JIS, A4, B5 JIS, 11 × 17, 8¹/₂ × 14, 8¹/₂ × 11, 12 × 18): 15 sheets

  In the Mixed Sizes mode: 30 sheets

When stapling B4 JIS, 8¹/₂ × 14 or larger paper sizes, be sure to extend the paper support plate of the finisher tray.

When the number of copies exceeds tray capacity, copying stops. If this happens, remove the copies from the shift tray, and then resume copying. The tray capacity for the stapled sheets is as follows: (paper weight: 80 g/m², 20 lb.)

• 1000-sheet finisher

  A4, 8¹/₂ × 11: 2 to 9-leaf binding...100 copies, 10 to 50-leaf binding...100 to 20 copies

  A4, B5 JIS, 8¹/₂ × 11: 2 to 9-leaf binding...100 copies, 10 to 50-leaf binding...50 to 10 copies

  A3, B4 JIS, 11 × 17, 8¹/₂ × 14, 12 × 18: 2 to 9-leaf binding...50 copies, 10 to 30-leaf binding...50 to 10 copies

• 3000-sheet finisher

  A4, 8¹/₂ × 11: 2 to 19-leaf binding...150 copies, 20 to 50-leaf binding...150 to 60 copies

  A4, B5 JIS, 8¹/₂ × 11: 2 to 14-leaf binding...100 copies, 15 to 50-leaf binding...100 to 30 copies

  A3, B4 JIS, 11 × 17, 8¹/₂ × 14: 2 to 14-leaf binding...100 copies, 15 to 30-leaf binding...100 to 33 copies

  In Mixed Sizes mode (A3 and A4, B4 JIS and B5 JIS, 11 × 17 and 8¹/₂ × 11): 2 to 30-leaf binding...50 copies

• Booklet finisher

  A4, 8¹/₂ × 11: 2 to 12-leaf binding...150 copies, 13 to 50-leaf binding...150 to 40 copies

  A4, B5 JIS, 8¹/₂ × 11: 2 to 9-leaf binding...100 copies, 10 to 50-leaf binding...100 to 20 copies

  A3, B4 JIS, 11 × 17, 8¹/₂ × 14, 12 × 18: 2 to 9-leaf binding...100 copies, 10 to 30-leaf binding...100 to 33 copies

  When stapling center (A3, B4 JIS, A4, B5 JIS, 11 × 17, 8¹/₂ × 14, 8¹/₂ × 11): 2 to 5-leaf binding...30 copies, 6 to 10-leaf binding...15 copies, 11 to 15-leaf binding...10 copies

  In Mixed Sizes mode (A3 and A4, B4 JIS and B5 JIS, 11 × 17 and 8¹/₂ × 11): 2 to 30-leaf binding...50 copies

You cannot change stapling positions during copying.

When the original image is rotated, the staple orientation changes by 90°.

The maximum original image size that can be rotated is as follows: Metric version: A4, Inch version: 8¹/₂ × 11

When using Slant, Left 2, or Top 2 with the Combine, Double Copies or Auto Reduce / Enlarge function, “Blank part will appear. Check orientation.” message may appear depending on the orientation of originals and paper you placed. In this case, change the paper orientation.

When Top or Bottom is selected and the paper with the same orientation as the original is not loaded, the image is rotated and the paper with the same size and the different orientation is selected.

When Left 2, or Top 2 is selected, the following settings are useful to rotate images appropriately:

• Auto Reduce / Enlarge or Auto Paper Select

• Replace Auto Tray Switching with With Image Rotation in User Tools.

If you select Center with the booklet finisher (optional), the machine staples and folds the paper in the center, then delivers the paper folded.

You cannot punch on thick paper heavier than 163 g/m² (43 lb.).

When using Punch and Combine, Double Copies, or Auto Reduce/Enlarge, the message “Blank part will appear. Check orientation.” may appear because of the orientation of the original and the copy paper. If this occurs, change the orientation of the copy paper.

Since punch holes are made in each copy, the punch hole positions vary slightly.

Punchable paper sizes are as follows:

• Booklet finisher/3000-sheet finisher

  • 2 and 4 holes type (2 holes)

    : A3 to A5, 11 × 17 to 5¹/₂ × 8¹/₂

    : A4 to A5, 8¹/₂ × 11, 5¹/₂ × 8¹/₂

  • 2 and 4 holes type (4 holes)

    : A3, B4 JIS, 11 × 17

    : A4, B5 JIS, 8¹/₂ × 11

  • 2 and 3 holes type (2 holes)

    : A3 to A5, 11 × 17 to 5¹/₂ × 8¹/₂

    : A4 to A5, 8¹/₂ × 11, 5¹/₂ × 8¹/₂

  • 2 and 3 holes type (3 holes)

    : A3, B4 JIS, 11 × 17

    : A4, B5 JIS, 8¹/₂ × 11

If the calculated ratio is over the maximum or under the minimum ratio, it is automatically adjusted to within available range. However, with some ratios, parts of the image might not be copied or margins will appear on copies.

The machine selects reproduction ratios of between 25-400%.

The reproduction ratio you can specify are 25-400%.

When entering a percentage ratio, you can specify any value in the permitted range, regardless of original or copy paper size. However, depending on settings and other conditions, part of the image may not be copied, or margins will appear on copies.

When entering a size in mm (inch), if the calculated ratio is over the maximum or under the minimum ratio, it is automatically adjusted to within available range. However, with some ratios, parts of the image might not be copied or margins will appear on copies.

The numbers appear to overlap the copied image in some cases.

Depending on paper size, if you change the stamp size, parts of the stamp might not be printed.

When Date Stamp is used with the Combine, Magazine, or Booklet function, the date stamp is printed as follows:

• With the Combine function

  

• With the Magazine or Booklet function

  

When Page Numbering is used with the Combine, Magazine, or Booklet function, page numbers are printed as follows:

• Per Original is selected in Page Numbering in Combine:

  With 1 Sided/2 Sided using the Combine function

  

  With the Magazine or Booklet function

  

• Per Copy is selected in Page Numbering in Combine:

  With 1 Sided/2 Sided using the Combine function

  

If you combine this function with the Duplex (Top to Top) function and select [P1,P2...] or [1/5,2/5...], page numbers on the back are printed as follows:

If you set a binding margin that is too wide, part of the image may not be copied.

When making copies in Combine mode, the binding margin is added to the copies after the combination is finished.

When 2 Sided 1 Sided is selected, set the binding margins for the original's front and back pages.

The width of the erased margin varies depending on the reproduction ratio.

Depending on the paper size, ratio, and orientation, parts of repeated images may not be copied.

Though the original is set to a different orientation from the paper loaded, the machine will not rotate the image by 90° (Rotate copy).

The machine sets the reproduction ratio automatically to meet the paper size and copies the originals together onto the paper.

The reproduction ratios selectable by the machine are 25-400%.

If the calculated ratio is under the minimum ratio, it is automatically adjusted to within available range. However, with some ratios, parts of the image might not be copied.

If the orientation of originals is different from that of the copy paper, the machine will automatically rotate the image by 90° to make copies properly.

You cannot copy with originals different in size and orientation.

If the number of originals scanned is less than a multiple of 4, the last page is copied blank.

In Magazine mode, the copying may take some time after scanning originals.

When the optional booklet finisher is installed, if you select Staple: Center in Magazine mode, the machine staples and folds the paper in the center, then delivers the paper folded.

If Blank mode is selected, the cover will not be counted as a copy.

The settings made under Cover Sheet Tray in User Tools determine whether or not the front and back covers are duplex printed.

• At Mode Selected... Settings made in Cover Sheet Tray will take priority.

• Full Time... Settings made in Paper Type will take priority.

This function cannot be used with mixed sizes mode.

When Combine (1 Sided 2 Sided) has been selected, specified pages will always be copied on the front of copies in the same way as in Chapters mode.

This function cannot be used with mixed sizes mode.

If you do not copy onto slip sheets, they are excluded from the number of copies counted.

This function cannot be used with mixed sizes mode.