IP-Fax Settings

This section describes the User Tools in the IP-Fax Settings menu under Fax Features.

Default settings are shown in bold type.

Make settings to use IP-Fax.

Set H.323 for the gatekeeper, SIP for SIP server, and the VoIP gateway to G3 fax if necessary. Check the settings of the network to which this machine is connected before making settings.

The following characters can be used for registration of the alias telephone number in H.323 Setting. Make sure you enter these characters correctly:

Numbers
Symbols ( and )

The following characters can be used for registration of the SIP User Name in SIP Settings. Make sure you enter these characters correctly:

Alphanumeric symbols (lower and upper cases)
Symbols (;?:&=$,-_.!~'@()%/[])

Use numbers and periods (".") to enter the correct IP addresses for the gatekeeper, SIP server, and VoIP gateway. To obtain the correct IP addresses, consult administrator.

Enable H.323

Specify whether or not H.323 is used for IP-Fax transmission.

The default setting is Off.

Enable SIP

Specify whether or not SIP is used for IP-Fax transmission.

The default setting is Off.

H.323 Settings

Set the IPv4 address and alias telephone number of the gatekeeper.

To use the gatekeeper, set the parameter setting (switch 34, bit 0) to "On".

The default parameter setting for switch 34, bit 0 is Off.

Select [Fax Features] using [] or [], and then press the [OK] key.
Select [IP-Fax Settings] using [] or [], and then press the [OK] key.
Select [H.323 Settings] using [] or [], and then press the [OK] key.
Select [Gatekeeper Address (Main)] using [] or [], and then press the [OK] key.
Enter the IPv4 address of the gatekeeper, and then press the [OK] key.
Select [Own Fax No.] using [] or [], and then press the [OK] key.
Enter Own Fax No. and then press the [OK] key.
Press the [User Tools/Counter] key.

SIP Settings

Set the SIP server's IP address or host name, and SIP user name. You can register either an IPv4 or IPv6 address for the SIP server. You cannot register an IPv4-mapped address.

To use the SIP server, set the parameter setting (switch 34, bit 1) to "On".

The default parameter setting for switch 34, bit 1 is Off.

Select [Fax Features] using [] or [], and then press the [OK] key.
Select [IP-Fax Settings] using [] or [], and then press the [OK] key.
Select [SIP Settings] using [] or [], and then press the [OK] key.
Select [Proxy Server Addr. (Main)] using [] or [], and then press the [OK] key.
A proxy server relays call requests and responses.
Enter the IP address of the proxy server, and then press the [OK] key.
Select [Redirect Svr. Addr. (Main)] using [] or [], and then press the [OK] key.
A redirect server processes request destination inquiries.
Enter the IP address of the redirect server, and then press the [OK] key.
Select [Registrar Address (Main)] using [] or [], and then press the [OK] key.
A register server registers location information of user agents (which correspond to telephones or facsimiles on public telephone lines) on an IP network.
Enter the IP address of the register server, and then press the [OK] key.
Select [SIP User Name] using [] or [], and then press the [OK] key.
Enter SIP User Name, and then press the [OK] key.
Select [SIP Digest Authentication] using [] or [], and then press the [OK] key.
Specify whether to perform SIP digest authentication, and then press the [OK] key.
If you select [On], enter the password using up to 128 characters.
Press the [User Tools/Counter] key.

Gateway Settings

Register, change, or delete the VoIP gateway used for transmission to IP-Fax. Register to use the VoIP gateway without using the gatekeeper/SIP server. You can register either an IPv4 or IPv6 address for the Gateway. You cannot register an IPv4-mapped address.

Programming/Changing the VoIP gateway:

Select [Fax Features] using [] or [], and then press the [OK] key.
Select [IP-Fax Settings] using [] or [], and then press the [OK] key.
Select [Gateway Settings] using [] or [], and then press the [OK] key.
Select [Program/Change] using [] or [], and then press the [OK] key.
Select [Not Programmed] using [] or [], and then press the [OK] key.
Enter the Prefix using the number key, and then press the [OK] key.
For documents sent using a VoIP gateway to G3 Fax, prefixes can be used. If the first several digits of IP-Fax number and the VoIP gateway- specific prefix are identical, documents can be transmitted using the registered digits of the VoIP gateway. For example, if both 03 and 04 have been registered as VoIP gateway number while 0312345678 is also specified, documents can be transmitted via a VoIP gateway for which 03 is used as a prefix.
When you wish to use the VoIP gateways regardless of the IP-Fax destination numbers, register only the VoIP gateway addresses without registering the prefix.
Enter VoIP gateway address and then press the [OK] key.
Select [H.323] or [SIP] using [] or [], and then press the [OK] key.
Press the [User Tools/Counter] key.

Deleting VoIP gateway:

Select [Fax Features] using [] or [], and then press the [OK] key.
Select [IP-Fax Settings] using [] or [], and then press the [OK] key.
Select [Gateway Settings] using [] or [], and then press the [OK] key.
Select [Delete] using [] or [], and then press the [OK] key.
Select the VoIP gateway you want to delete using [] or [], and then press the [OK] key.
Press [Yes].
Press the [User Tools/Counter] key.

For details about setting parameters, see "Parameter Settings".

Parameter Settings