Skip headerimage
ManualsContentsPreviousNextHelp

Input/Output

This section describes the user tools in the Input/Output menu under Copier / Document Server Features.

Default settings are shown in bold type.

Switch to Batch

You can select to have Batch mode or SADF mode displayed when you press [Special Original].

The default setting is Batch.

SADF Auto Reset

In SADF mode, an original must be set within a specified time after the previous original has been fed.

The default setting is 5 second(s).

You can adjust this time from 3 to 99 seconds in increments of 1 second.

Rotate Sort: Auto Paper Continue

Specify to continue copying when paper of the required orientation has run out during rotate sort.

The default setting is Off.

  • On

    Copying continues using copy paper of a different orientation. The copy job will finish even if you have left the machine.

  • Off

    When paper of the required orientation runs out, the machine stops copying and prompts you to supply copy paper. After you have loaded paper, the machine will continue copying.

Memory Full Auto Scan Restart

When memory becomes full while scanning originals, the machine can make copies of scanned originals first, and then automatically proceed scanning remaining originals.

The default setting is Off.

  • On

    You can leave the machine unattended to make copies, but sorted pages will not be sequential.

  • Off

    When memory becomes full, the machine stops operation allowing you to remove the copy pages delivered on the output tray.

Letterhead Setting

If you select [Yes] in this function, the machine rotates the image correctly.

The default setting is No.

Orientation-fixed (top to bottom) or two-sided paper might not be printed correctly depending on how the originals and paper are placed.

Staple Position

Specify which Top 2 staples or Bottom shown on the initial display with priority.

The optional finisher is required to use this function.

Type 1 and 2

  • When the Finisher SR3010 is installed:

    The default setting for "Staple Position 1" is Slant.

    The default setting for "Staple Position 2" is Bottom Slant.

    The default setting for "Staple Position 3" is Left 2.

    The default setting for "Staple Position 4" is Top 2.

  • When the Finisher SR790 is installed:

    The default setting for "Staple Position 1" is Top 1.

    The default setting for "Staple Position 2" is Bottom 1.

    The default setting for "Staple Position 3" is Left 2.

    The default setting for "Staple Position 4" is Top 2.

  • When the Booklet Finisher SR3000 is installed:

    The default setting for "Staple Position 1" is Top 1.

    The default setting for "Staple Position 2" is Centre.

    The default setting for "Staple Position 3" is Left 2.

    The default setting for "Staple Position 4" is Top 2.

Type 3 and 4

  • When the Finisher SR790 is installed:

    The default setting for "Staple Position 1" is Top 1.

    The default setting for "Staple Position 2" is Bottom 1.

    The default setting for "Staple Position 3" is Left 2.

    The default setting for "Staple Position 4" is Top 2.

  • When the Finisher SR3030 is installed:

    The default setting for "Staple Position 1" is Top 1.

    The default setting for "Staple Position 2" is Slant.

    The default setting for "Staple Position 3" is Left 2.

    The default setting for "Staple Position 4" is Top 2.

  • When the Booklet Finisher SR3020 is installed:

    The default setting for "Staple Position 1" is Top 1.

    The default setting for "Staple Position 2" is Centre.

    The default setting for "Staple Position 3" is Left 2.

    The default setting for "Staple Position 4" is Top 2.

Simplified Screen: Finishing Types

You can select which key is displayed with higher priority for "Finishing Types" on the Simplified Screen.

The default setting for "Simplified Screen: Finishing Types 1" has not been set.

The default setting for "Simplified Screen: Finishing Types 2" has not been set.

The default setting for "Simplified Screen: Finishing Types 3" has not been set.

Reference