BackForward
Search

User GuidePro C7500/C7500H

White Stains/Ghosting When Printing on Transparent Film

When printing is performed on a transparent film, white ghosting occurs all over the film.

Depending on the printed image, ghosting of the image pattern may occur.

Illustration of cloudy film

[A]: Ghosting occurs at an interval of 278 mm (10.9 mm) (one rotation of the fusing belt).

[B]: White stains on the entire image

Cause:

Because of the heat on the fusing unit, the surface profile of the fusing belt may be transferred to the transparent film, causing white ghosting on the part of the transparent film where images are not printed.

Furthermore, if toner wax adheres, ghosting occurs on the corresponding area.

Solution:

(a) Decrease the printing speed

1If the paper is not registered as custom paper, register the brand of the paper.

2Decrease the line speed. This will decrease the throughput, but is it OK?

Yes

Go to the next step.

No

Proceed to Step 5 of "(c) Adjust the fusing temperature (If [Print Speed] is set to [Low])".

3In [Detailed settings] for the custom paper you are using, select 1231: [Print Speed], and then decrease the value in the following corresponding settings by one level.

  • 1231-01: Print Speed: BW/FC/FCS: BW/FC/FCS

  • 1231-02: Print Speed: FCS: Clear/Special

  • 1231-03: Print Speed: FCS: White

  • 1231-04: Print Speed: FCS: Metallic

  • 1231-06: Print Speed: S: Clear/Special

  • 1231-07: Print Speed: S: White

  • 1231-08: Print Speed: S: Metallic

  • 1231-10: Print Speed: BW/FC/FCS: Fuser Setting HQ: BW/FC/FCS

  • 1231-11: Print Speed: FCS: Fuser Setting HQ: Clear/Special

  • 1231-12: Print Speed: FCS: Fuser Setting HQ: White

  • 1231-13: Print Speed: FCS: Fuser Setting HQ: Metallic

  • 1231-15: Print Speed: S: Fuser Setting HQ: Clear/Special

  • 1231-16: Print Speed: S: Fuser Setting HQ: White

  • 1231-17: Print Speed: S: Fuser Setting HQ: Metallic

For example, if the print speed is [High], lower it to [Middle], and if it is [Middle], lower it to [Low].

Proceed to "(b) Changing the fusing temperature (If [Print Speed] is set to [Middle])".

Proceed to "(c) Changing the fusing temperature (If [Print Speed] is set to [Low])".

(b) Adjust the fusing temperature (If [Print Speed] is set to [Middle])

1In [Detailed settings] for the custom paper you are using, select 1232: [Fusing Temperature], and then decrease the value in the following corresponding settings by 5°C.

  • 1232-01: Fusing Temperature: BW/FC/FCS: Heat Roller Temp

  • 1232-06: Fusing Temperature: FCS: Heat Roller Temp: Clear/Special

  • 1232-07: Fusing Temperature: FCS: Heat Roller Temp: White

  • 1232-08: Fusing Temperature: FCS: Heat Roller Temp: Metallic

  • 1232-26: Fusing Temperature: S: Heat Roller Temp: Clear/Special

  • 1232-27: Fusing Temperature: S: Heat Roller Temp: White

  • 1232-28: Fusing Temperature: S: Heat Roller Temp: Metallic

  • 1232-46: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Heat Roller Temp

  • 1232-51: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-52: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-53: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Metallic

  • 1232-71: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-72: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-73: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Metallic

2Print 5 or more A4 sheets. Has the problem been resolved?

Yes

Go to the next step.

No

Carry out "(a) Decrease the printing speed".

3Is the toner fusibility within the permissible range?

Note

  • The required level of fusibility is as follows.

    • The printed image does not come off.

    • The toner does not come off even if it is lightly rubbed by a nail.

    • The toner does not come off even if it is rubbed by the cloth for cleaning the contact glass.

Yes

Finished!

No

Change the print speed to "Low". Go to "(c) Changing the fusing temperature (If [Print Speed] is set to [Low])".

(c) Adjust the fusing temperature (If [Print Speed] is set to [Low])

1In [Detailed settings] for the custom paper you are using, select 1232: [Fusing Temperature], and then decrease the value in the following corresponding settings by 20°C.

  • 1232-01: Fusing Temperature: BW/FC/FCS: Heat Roller Temp

  • 1232-06: Fusing Temperature: FCS: Heat Roller Temp: Clear/Special

  • 1232-07: Fusing Temperature: FCS: Heat Roller Temp: White

  • 1232-08: Fusing Temperature: FCS: Heat Roller Temp: Metallic

  • 1232-26: Fusing Temperature: S: Heat Roller Temp: Clear/Special

  • 1232-27: Fusing Temperature: S: Heat Roller Temp: White

  • 1232-28: Fusing Temperature: S: Heat Roller Temp: Metallic

  • 1232-46: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Heat Roller Temp

  • 1232-51: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-52: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-53: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Metallic

  • 1232-71: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-72: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-73: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Metallic

2Select [Correct Temp: Initial Feed], and then set the value in the following corresponding settings to 0°C.

  • 1232-02: Fusing Temperature: BW/FC/FCS: Correct Temp: Initial Feed

  • 1232-10: Fusing Temperature: FCS: Correct Temp: Initial Feed: Clear/Special

  • 1232-11: Fusing Temperature: FCS: Correct Temp: Initial Feed: White

  • 1232-12: Fusing Temperature: FCS: Correct Temp: Initial Feed: Metallic

  • 1232-30: Fusing Temperature: S: Correct Temp: Initial Feed: Clear/Special

  • 1232-31: Fusing Temperature: S: Correct Temp: Initial Feed: White

  • 1232-32: Fusing Temperature: S: Correct Temp: Initial Feed: Metallic

  • 1232-47: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Correct Temp: Initial Feed

  • 1232-55: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Initial Feed: Clear/Special

  • 1232-56: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Initial Feed: White

  • 1232-57: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Initial Feed: Metallic

  • 1232-75: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Initial Feed: Clear/Special

  • 1232-76: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Initial Feed: White

  • 1232-77: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Initial Feed: Metallic

3Select [Correct Temp: Pre-Feed], and then set the value in the following corresponding settings to 5°C.

  • 1232-03: Fusing Temperature: BW/FC/FCS: Correct Temp: Pre-Feed

  • 1232-14: Fusing Temperature: FCS: Correct Temp: Pre-Feed: Clear/Special

  • 1232-15: Fusing Temperature: FCS: Correct Temp: Pre-Feed: White

  • 1232-16: Fusing Temperature: FCS: Correct Temp: Pre-Feed: Metallic

  • 1232-34: Fusing Temperature: S: Correct Temp: Pre-Feed: Clear/Special

  • 1232-35: Fusing Temperature: S: Correct Temp: Pre-Feed: White

  • 1232-36: Fusing Temperature: S: Correct Temp: Pre-Feed: Metallic

  • 1232-48: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Correct Temp: Pre-Feed

  • 1232-59: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Pre-Feed: Clear/Special

  • 1232-60: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Pre-Feed: White

  • 1232-61: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Pre-Feed: Metallic

  • 1232-79: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Pre-Feed: Clear/Special

  • 1232-80: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Pre-Feed: White

  • 1232-81: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Pre-Feed: Metallic

4Print 5 or more A4 sheets. Has the problem been resolved?

Yes

Proceed to Step 7.

No

Go to the next step.

5In [Detailed settings] for the custom paper you are using, select 1232: [Fusing Temperature], and then decrease the value in the following corresponding settings by 5°C.

  • 1232-01: Fusing Temperature: BW/FC/FCS: Heat Roller Temp

  • 1232-06: Fusing Temperature: FCS: Heat Roller Temp: Clear/Special

  • 1232-07: Fusing Temperature: FCS: Heat Roller Temp: White

  • 1232-08: Fusing Temperature: FCS: Heat Roller Temp: Metallic

  • 1232-26: Fusing Temperature: S: Heat Roller Temp: Clear/Special

  • 1232-27: Fusing Temperature: S: Heat Roller Temp: White

  • 1232-28: Fusing Temperature: S: Heat Roller Temp: Metallic

  • 1232-46: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Heat Roller Temp

  • 1232-51: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-52: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-53: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Metallic

  • 1232-71: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-72: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-73: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Metallic

6Print 5 or more A4 sheets. Has the problem been resolved?

Yes

Proceed to Step 7.

No

Repeat Steps 5.

7Is the toner fusibility within the permissible range?

Note

  • The required level of fusibility is as follows.

    • The printed image does not come off.

    • The toner does not come off even if it is lightly rubbed by a nail.

    • The toner does not come off even if it is rubbed by the cloth for cleaning the contact glass.

Yes

Finished!

No

No further improvement is likely. Contact your service representative.

Note

  • Select "Clear/Special" when using Neon Yellow, Neon Pink, or Invisible Red. Select "Metallic" when using Gold or Silver.

  • After performing the solution, it is recommended to perform the color calibration of the external printer controller.