BackForward
Search

User GuidePro C7500/C7500H

Toner Blasting (When Printing in 2 Colors)

In text or lines printed in two colors, toner blasting occurs to the second color toner.

Cause:

When different color toners overlap on the intermediate transfer belt when transferred, the toner of the second color is scattered around it, and the scattered toner is transferred directly to the paper in the paper transfer unit.

Occurrence conditions:

  • When toner adhesion is high

  • When printing on slippery paper

  • Paper is stored at low temperature or humidity

Solution:

1If the paper is not registered as custom paper, register the brand of the paper.

2Check to see if there is a margin to reduce the line speed, and if reducing throughput causes any problems.

Yes

Go to the next step.

No

Proceed to "Decreasing the Fusing Heat Roller Temperature.".

3In [Detailed settings] for custom paper, select 1231: [Print Speed] and reduce the print speed by one step according to the color mode you wish to use.

  • 1231-01: Print Speed: BW/FC/FCS: BW/FC/FCS

  • 1231-02: Print Speed: FCS: Clear/Special

  • 1231-03: Print Speed: FCS: White

  • 1231-04: Print Speed: FCS: Metallic

  • 1231-06: Print Speed: S: Clear/Special

  • 1231-07: Print Speed: S: White

  • 1231-08: Print Speed: S: Metallic

  • 1231-10: Print Speed: BW/FC/FCS: Fuser Setting HQ: BW/FC/FCS

  • 1231-11: Print Speed: FCS: Fuser Setting HQ: Clear/Special

  • 1231-12: Print Speed: FCS: Fuser Setting HQ: White

  • 1231-13: Print Speed: FCS: Fuser Setting HQ: Metallic

  • 1231-15: Print Speed: S: Fuser Setting HQ: Clear/Special

  • 1231-16: Print Speed: S: Fuser Setting HQ: White

  • 1231-17: Print Speed: S: Fuser Setting HQ: Metallic

For example, if the print speed is [High], lower it to [Middle], and if it is [Middle], lower it to [Low].

If you change the print speed to [Middle], go to the next step.

If you change it to [Low], go to Step 5.

4In [Detailed settings] for custom paper, select 1232: [Fusing Temperature] and decrease the temperature setting for the fusing heat roller by 5°C according to the color mode you wish to use.

  • 1232-01: Fusing Temperature: BW/FC/FCS: Heat Roller Temp

  • 1232-06: Fusing Temperature: FCS: Heat Roller Temp: Clear/Special

  • 1232-07: Fusing Temperature: FCS: Heat Roller Temp: White

  • 1232-08: Fusing Temperature: FCS: Heat Roller Temp: Metallic

  • 1232-26: Fusing Temperature: S: Heat Roller Temp: Clear/Special

  • 1232-27: Fusing Temperature: S: Heat Roller Temp: White

  • 1232-28: Fusing Temperature: S: Heat Roller Temp: Metallic

  • 1232-46: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Heat Roller Temp

  • 1232-51: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-52: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-53: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Metallic

  • 1232-71: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-72: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-73: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Metallic

Print the image. Has the problem been resolved? (10 or more sheets of A4 paper)

Yes

Finished!

No

Set [Print Speed] to [Low] according to Step 3, and then go to the next step.

5Decrease the temperature setting for the fusing heat roller by 20°C according to the color mode you wish to use.

  • 1232-01: Fusing Temperature: BW/FC/FCS: Heat Roller Temp

  • 1232-06: Fusing Temperature: FCS: Heat Roller Temp: Clear/Special

  • 1232-07: Fusing Temperature: FCS: Heat Roller Temp: White

  • 1232-08: Fusing Temperature: FCS: Heat Roller Temp: Metallic

  • 1232-26: Fusing Temperature: S: Heat Roller Temp: Clear/Special

  • 1232-27: Fusing Temperature: S: Heat Roller Temp: White

  • 1232-28: Fusing Temperature: S: Heat Roller Temp: Metallic

  • 1232-46: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Heat Roller Temp

  • 1232-51: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-52: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-53: Fusing Temperature: FCS: Fuser Setting HQ: Heat Roller Temp: Metallic

  • 1232-71: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Clear/Special

  • 1232-72: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: White

  • 1232-73: Fusing Temperature: S: Fuser Setting HQ: Heat Roller Temp: Metallic

6In [Detailed settings] for custom paper, select 1232: [Correct Temp: Initial Feed], and then set the temperature adjustment for the initial paper feeding to "0" according to the color mode you wish to use.

  • 1232-02: Fusing Temperature: BW/FC/FCS: Correct Temp: Initial Feed

  • 1232-10: Fusing Temperature: FCS: Correct Temp: Initial Feed: Clear/Special

  • 1232-11: Fusing Temperature: FCS: Correct Temp: Initial Feed: White

  • 1232-12: Fusing Temperature: FCS: Correct Temp: Initial Feed: Metallic

  • 1232-30: Fusing Temperature: S: Correct Temp: Initial Feed: Clear/Special

  • 1232-31: Fusing Temperature: S: Correct Temp: Initial Feed: White

  • 1232-32: Fusing Temperature: S: Correct Temp: Initial Feed: Metallic

  • 1232-47: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Correct Temp: Initial Feed

  • 1232-55: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Initial Feed: Clear/Special

  • 1232-56: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Initial Feed: White

  • 1232-57: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Initial Feed: Metallic

  • 1232-75: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Initial Feed: Clear/Special

  • 1232-76: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Initial Feed: White

  • 1232-77: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Initial Feed: Metallic

7Select 1232: [Correct Temp: Initial Feed], and then set the temperature adjustment before paper feeding to "5°C" according to the color mode you wish to use.

  • 1232-03: Fusing Temperature: BW/FC/FCS: Correct Temp: Pre-Feed

  • 1232-14: Fusing Temperature: FCS: Correct Temp: Pre-Feed: Clear/Special

  • 1232-15: Fusing Temperature: FCS: Correct Temp: Pre-Feed: White

  • 1232-16: Fusing Temperature: FCS: Correct Temp: Pre-Feed: Metallic

  • 1232-34: Fusing Temperature: S: Correct Temp: Pre-Feed: Clear/Special

  • 1232-35: Fusing Temperature: S: Correct Temp: Pre-Feed: White

  • 1232-36: Fusing Temperature: S: Correct Temp: Pre-Feed: Metallic

  • 1232-48: Fusing Temperature: BW/FC/FCS: Fuser Setting HQ: Correct Temp: Pre-Feed

  • 1232-59: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Pre-Feed: Clear/Special

  • 1232-60: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Pre-Feed: White

  • 1232-61: Fusing Temperature: FCS: Fuser Setting HQ: Correct Temp: Pre-Feed: Metallic

  • 1232-79: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Pre-Feed: Clear/Special

  • 1232-80: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Pre-Feed: White

  • 1232-81: Fusing Temperature: S: Fuser Setting HQ: Correct Temp: Pre-Feed: Metallic

8Print the image. Has the problem been resolved? (10 or more sheets of A4 paper)

Yes

Go to the next step.

No

Proceed to "Decreasing the Fusing Heat Roller Temperature".

9Check to see if the fusibility is within the acceptable range.

Note

  • The required level of fusibility is as follows.

    • The printed image does not come off.

    • The toner does not come off even if it is lightly rubbed by a nail.

    • The toner does not come off even if the image is wiped with an optical cloth.

Yes

Finished!

No

No further improvement is likely.

Decreasing the Fusing Heat Roller Temperature

1In [Detailed settings] for custom paper, select 1232: [Fusing Temperature] and decrease the temperature setting for the fusing heat roller by 5°C according to the color mode you wish to use.

2Print the image. Has the problem been resolved? (10 or more sheets of A4 paper)

Yes

Go to the next step.

No

Start over from Step 1.

3Check to see if the fusibility is within the acceptable range.

Note

  • The required level of fusibility is as follows.

    • The printed image does not come off.

    • The toner does not come off even if it is lightly rubbed by a nail.

    • The toner does not come off even if the image is wiped with an optical cloth.

Yes

Finished!

No

No further improvement is likely.

Note

  • Select "Clear/Special" when using Neon Yellow, Neon Pink, or Invisible Red. Select "Metallic" when using Gold or Silver.

  • After performing the solution, it is recommended to perform the color calibration of the external printer controller.