User GuideIM 2702

Interface Settings (System Settings)

This section describes the settings in the [Interface Settings] menu under [System Settings].

Network

This section describes the settings in the [Network] menu under [Interface Settings].

Items

Description

Machine IPv4 Address

Specify the machine's IPv4 Address and Subnet Mask. Machine's IPv4 Address can be specified by an address or acquired from the DHCP server automatically.

  • Default: [Auto-Obtain (DHCP)]

IPv4 Gateway Address

Specify the IPv4 address of the router or host computer used as a gateway.

  • Default: 0.0.0.0

Machine IPv6 Address

Displays the machine's IPv6 address.

  • Link-local Address

  • Manual Configuration Address

  • DHCPv6 Address

  • Stateless Address: 1–5

    Current value when [IPv6 Stateless Address Autoconfiguration] is specified to "Active" is displayed.

IPv6 Gateway Address

Displays the machine's IPv6 gateway address.

IPv6 Stateless Address Autoconfiguration

Specify whether to specify the address automatically using IPv6 Stateless Address Autoconfiguration.

  • Default: [Active]

DNS Configuration

Specify the IPv4 address of the DNS server. IPv4 Address of the DNS server can be specified by an address or acquired from the DHCP server automatically. You can confirm the connection to the DNS server.

  • Default: [Auto-Obtain (DHCP)]

DDNS Configuration

Specify whether you use the Dynamic DNS function.

  • Default: [Active]

Domain Name

Specify the domain name. Obtain the domain name from the DHCP server automatically or enter the domain name up to 63 characters.

  • Default: [blank]

Effective Protocol

Select protocols to use in the network.

  • Default

    IPv4: [Active]

    IPv6: [Inactive]

    @Remote Service: [Active]

    Firmware Update (IPv4): [Active]

    Firmware Update (IPv6): [Active]

SMB Client Advanced Settings

Select the port number from 139 or 445 for the SMB data transmission. You can also specify whether to specify the SMBv2/v3 transmission Inactive. When SMBv2/v3 is Inactive, transmission is performed with SMBv1.

  • Default

    • Port Number: [445]

    • SMBv2/SMBv3: [Active]

Ethernet Speed

Specify the access speed between the machine and the network devices. When the communication is unstable, fix the Transmission Speed to 10 Mbps or 100 Mbps. When you specify Full Duplex in this case, specify the same Transmission Speed of the connected device as the machine.

  • Default: [AutoSelct:Disable 1Gbps]

LAN Type

You can specify which you use for connection, wired LAN (Ethernet) or wireless LAN.

  • Default: [Wireless LAN]

Permit SNMPv3 Communication

Specify the communication of SNMPv3 protocol whether to use the encrypted communication only or encrypted and cleartext communication in accordance with the settings of the machine.

When you specify [Encryption Only], you need to set [Encryption Password] for the administrator by [Administrator Tools][Program/Change Administrator].

  • Default: [Encryption / Cleartext]

Permit SSL / TLS Communication

Specify the communication of SNMPv3 protocol whether to use the encrypted communication of SSL/TLS or encrypted and cleartext communication in accordance with the settings of the machine.

When you specify [Ciphertext Only], you need to install the Server Certificate for the machine.

  • Default: [Ciphertext / Cleartext]

Host Name

Specify the host name. When you do not specify the name, the text starting with RNP is automatically set.

Enter the host name up to 63 characters. You cannot specify the host name starting with "RNP" or "rnp".

You cannot enter a host name starting with or ending with a hyphen. You cannot enter a host name in which hyphens are used consecutively.

  • Default: [RNPXXXXX]

    (MAC Address of the Interface is used for XXXXX.)

Machine Name

Enter the machine name up to 31 characters. When you manage the machine with Web Image Monitor or Machine Management software, this is displayed as "Device Name".

IEEE 802.1X Authentication for Ethernet

Specify when you use the IEEE 802.1X authentication for Ethernet.

  • Default: [Inactive]

For details about "Configuring IPsec Settings", see "Security Reference" on our website.

Restore IEEE 802.1X Authentication to Defaults

Return the settings to their defaults when the machine cannot be connected with the IEEE 802.1X authentication.

For details about "Configuring IPsec Settings", see "Security Reference" on our website.

USB Speed

Specify the USB speed. You can select from [Auto Select] or [Full Speed].

  • Default: [Auto Select]

DIPRINT Timeout Period

Specify the timeout time for DIPRINT printing.

  • Default: [15 seconds]

Note

  • We recommend only enabling one of the following settings: IPv6 gateway address manual settings, or IPv6 stateless address automatic settings. If you do not want the IPv6 gateway address to be changed automatically, do not enable IPv6 gateway address manual settings, and IPv6 stateless automatic settings at the same time.

  • An IPv6 gateway address automatically acquired may be set by the router if the following settings are enabled at the same time;

    • IPv6 gateway address manual settings and either IPv6 stateless address automatic settings

    • IPv6 stateless address automatic settings

Wireless LAN

This section describes the settings in the [Wireless LAN] menu under [Interface Settings].

Connecting to a Wireless LAN

Items

Description

Communication Mode

Specify the communication mode of the wireless LAN. The following modes are available:

[802.11 Ad-hoc Mode]

[Infrastructure Mode]

[Direct Connection: Group Owner Mode]

[Direct Connection Mode]

  • Default: [Infrastructure Mode]

Selecting the Network Connection Method

SSID Setting

Specify SSID when [Communication Mode] is [Infrastructure Mode] or [802.11 Ad-hoc Mode].

In [Infrastructure Mode] enter the SSID of the connected access point. In [802.11 Ad-hoc Mode], the entered SSID will be the name of the Ad-hoc network.

The characters that can be used are ASCII 0x20-0x7e (32 bytes), and are distinguished between upper and lower cases.

For connecting to the access point to which ANY connection is permitted, enter blank or "ANY" in the SSID field.

Ad-hoc Channel

Specify the channel to use when [Communication Mode] is [802.11 Ad-hoc Mode]. Select the channel depending on the radio wave status.

  • Default: [11]

Security Method

Specify the encryption of the Wireless LAN. To encrypt, select one of WEP, WPA2-PSK, or WPA2 as the Security Method. If you select WPA2, install the authentication methods and certificate.

For details about "Configuring IPsec Settings", see "Security Reference" on our website.

  • Default: [Off]

Wireless LAN: Easy Setup / Direct Connection

Specify Wireless LAN: Easy Setup / Direct Connection to connect to a WPS-compatible access point. Push the button of the access point or enter the PIN code displayed on the machine in the access point on the computer for the connection.

  • Default: [Push Button]

Direct Connection Settings

Specify to connect to the machine from the mobile device.

Specify the device name, password, machine's IPv4 address for direct connection.

Connecting to the Machine from a Mobile Device Using the Wi-Fi Direct Function

Wireless LAN Signal

Display the machine's radio wave status when the machine is connected by specifying [Communication Mode] to [Infrastructure Mode]. If the radio wave is weak, change the access point to connect or review the machine's environment.

Restore Factory Defaults

You can return the wireless LAN settings to their defaults.

Country / Region

The list of countries and regions is displayed.

Specify the correct country or region, and then press [OK].

Direct Connection

This section describes the settings in the [Direct Connection] menu under [Interface Settings].

Connecting to the Machine from a Mobile Device Using the Wi-Fi Direct Function

Items

Description

Active/Inactive

Specify whether to enable Direct Connection: Group Owner Mode set to Active from the direct connection widget placed on the Home screen.

  • Default: [Inactive]

Direct Connection Settings

Specify to connect to the machine from the mobile device.

Specify the device name, password, and machine's IPv4 address for direct connection.

Fix SSID

Specify whether to fix SSID when the direct connection is set to Active.

  • Default: [Off]