Current Machine Status
This section explains how you can check the machine's status and the items displayed.
You can check the machine's status as follows:
"lpq" command
LPR Port Monitor must be enabled to use lpq command in Windows."stat" parameters of "rsh", "rcp", and "ftp" commands
"rsh" and "rcp" cannot be used in a Windows environment."status" command of telnet
Check the error contents that may be printed in the configuration page.
Messages |
Description |
|---|---|
|
Call Service Center |
There is a malfunction in the machine. |
|
Canceling Job... |
The job is being reset. |
|
Check Paper: Bypass Tray |
Check that the paper size, orientation, and paper type are correct. |
|
Configuring... |
Setting is being changed. |
|
Cover Open: Front Cover |
The front cover is open. |
|
Current Job Suspended |
The current job is suspended. |
|
Empty: Toner |
The toner cartridge is empty. |
|
Energy Saver Mode |
The machine is in Energy Saver mode. |
|
Error: Ethernet Board |
An Ethernet board error has occurred. |
|
Error: HDD Board |
A hard disk drive board error has occurred. |
|
Error: Optional Font |
An error has occurred in the font file of the machine. |
|
Error: Parallel I/F Board |
An error has occurred in the parallel interface. |
|
Error: PDL |
An error has occurred in the page description language. |
|
Error: USB Interface |
An error has occurred in the USB interface. |
|
Error: Wireless Card |
There is a problem with IEEE802.11a/b/g/n interface unit are not supported. |
|
Full: Waste Toner |
Waste Toner Bottle is full. |
|
Hex Dump Mode |
It is a hex dump mode. |
|
Independent-supplier Toner |
Toner cartridges other than genuine ones are set. |
|
Jobs Suspended |
All jobs are suspended. |
|
Loading Toner… |
Toner is being supplied. |
|
Low: Toner |
Toner is almost running out. |
|
Malfunction: Bypass Tray |
There is a problem with the bypass tray. |
|
Malfunction: Tray 1 |
There is a problem with Tray 1. |
|
Malfunction: Tray 2 |
There is a problem with Tray 2. |
|
Malfunction: Tray 3 |
There is a problem with Tray 3. |
|
Malfunction: Tray 4 |
There is a problem with Tray 4. |
|
Mismatch: Paper Size |
Indicated paper tray does not contain paper of selected size. |
|
Mismatch: Paper Size and Type |
Indicated paper tray does not contain paper of selected size and type. |
|
Mismatch: Paper Type |
Indicated paper tray does not contain paper of selected type. |
|
Nearly Full: Waste Toner |
Waste Toner Bottle is nearly full. |
|
No Paper: Selected Tray |
There is no paper in the specified tray. |
|
Not Detected: Fuser Unit |
The fusing unit is not correctly set. |
|
Not Detected: Input Tray |
There is no paper in the specified tray or the paper tray is not correctly set. |
|
Not Detected: Drum Unit |
The drum unit is not correctly set. |
|
Offline |
Machine is offline. |
|
Paper in Duplex Unit |
The paper remains in the duplex unit. |
|
Paper Misfeed: Bypass Tray |
The paper has jammed in the bypass Tray. |
|
Paper Misfeed: Duplex Unit |
The paper has jammed in Duplex Unit. |
|
Paper Misfeed: Internal Path |
The paper has jammed inside the machine. |
|
Paper Misfeed: Tray 1 |
The paper has jammed in Tray 1. |
|
Paper Misfeed: Tray 2 |
The paper has jammed in Tray 2. |
|
Paper Misfeed: Tray 3 |
The paper has jammed in Tray 3. |
|
Paper Misfeed: Tray 4 |
The paper has jammed in Tray 4. |
|
Printing... |
Printing is in progress. |
|
Proxy User/Password Incorrect |
The proxy user name and/or password setting is incorrect. |
|
Ready |
The machine is ready to print. |
|
Renewing Remote Certificate |
The remote certificate is being renewed. |
|
SD Card Authentication failed |
SD card authentication failed. |
|
Supplies Order Call failed |
The supply order call has failed. |
|
Tray Error: Duplex Printing |
Selected paper tray cannot be used for duplex printing. |
|
Warming Up... |
The machine is warming up. |