Previous
(a) Executing Fusing Belt Manual Smoothing Adjustment
In the [Machine: Maintenance] group on the [Adjustment Settings for Operators] menu, select 0508: [Manually Smooth Fusing Belt], and then execute [Uneven Gloss: Short Time].
Print the image. Has the problem been resolved?
Yes |
Go to the next step. |
No |
Repeat Steps 1 and 2. |
To prevent this problem, adjust the values in print speed and fusing temperature. This will decrease the throughput, but is it OK?
Yes |
Proceed to "(b) Adjusting the values in Print Speed and Fusing Temperature". |
No |
Finished! If the problem recurs, try this solution again. |
(b) Adjusting the values in Print Speed and Fusing Temperature
In [Advanced Settings] for the custom paper you are using, select 1231: [Print Speed], and then set the value in the following corresponding settings to [Low].
[BW/FC/FCS]
[BW/FC/FCS]
[FCS]
[Clear/Special], [White]
[S]
[Clear/Special], [White]
[BW/FC/FCS: Fuser Setting HQ]
[BW/FC/FCS]
[FCS: Fuser Setting HQ]
[Clear/Special], [White]
[S: Fuser Setting HQ]
[Clear/Special], [White]
Select 1232: [Fusing Temperature], and then decrease the value in the following corresponding settings by 20°C.
[BW/FC/FCS]
[Heat Roller Temp]
[FCS]
[Heat Roller Temp: Clr/Sp], [Heat Roller Temp: White]
[S]
[Heat Roller Temp: Clr/Sp], [Heat Roller Temp: White]
[BW/FC/FCS: Fuser Setting HQ]
[Heat Roller Temp]
[FCS: Fuser Setting HQ]
[Heat Roller Temp: Clr/Sp], [Heat Roller Temp: White]
[S: Fuser Setting HQ]
[Heat Roller Temp: Clr/Sp], [Heat Roller Temp: White]
Select 1232: [Fusing Temperature], and then set the value in the following corresponding settings to 0°C.
[BW/FC/FCS]
[Corct Temp: Initial Feed]
[FCS]
[Corct Temp: Init Fd: Clr/Sp], [Corct Temp: Init Fd: White]
[S]
[Corct Temp: Init Fd: Clr/Sp], [Corct Temp: Init Fd: White]
[BW/FC/FCS: Fuser Setting HQ]
[Corct Temp: Initial Feed]
[FCS: Fuser Setting HQ]
[Corct Temp: Init Fd: Clr/Sp], [Corct Temp: Init Fd: White]
[S: Fuser Setting HQ]
[Corct Temp: Init Fd: Clr/Sp], [Corct Temp: Init Fd: White]
Select 1232: [Fusing Temperature], and then set the value in the following corresponding settings to 5°C.
[BW/FC/FCS]
[Corct Temp: Pre-Feed]
[FCS]
[Corct Temp: Pre-Fd: Clr/Sp], [Corct Temp: Pre-Fd: White]
[S]
[Corct Temp: Pre-Fd: Clr/Sp], [Corct Temp: Pre-Fd: White]
[BW/FC/FCS: Fuser Setting HQ]
[Corct Temp: Pre-Feed]
[FCS: Fuser Setting HQ]
[Corct Temp: Pre-Fd: Clr/Sp], [Corct Temp: Pre-Fd: White]
[S: Fuser Setting HQ]
[Corct Temp: Pre-Fd: Clr/Sp], [Corct Temp: Pre-Fd: White]
After performing the solution, it is recommended to perform the color calibration of the external controller.
