Skip header
 

Cover/Designation/Slip/Separation Sheet

This section explains the paper tray settings in the [Cover/Designation/Slip/Separation Sheet] menu under [Tray Paper Settings].

Front Cover (Front Cover Sheet Tray)

You can specify and display the paper tray in which to load front cover sheets.

You can also specify the display time and copying method for duplex copying.

  • Tray to Program

    • Tray 1

    • Tray 2

    • Tray 3

    • Tray 4

    • Tray 5

    • Tray 6

    • Tray 7

    • Tray 8

    • Tray A

    • Intpsr. Upper (when the interposer is installed.)

    • Intpsr. Lower (when the interposer is installed.)

    Default: Off (Tray is not specified.)

  • Apply Duplex

    • Yes

    • No

    Default: [Yes]

  • Display Time

    • At Mode Selected

    • Full Time

    Default: [At Mode Selected]

Note

  • When you select an interposer tray, you cannot change the [Display Time] and [Apply Duplex] settings.

  • When [At Mode Selected] is selected for [Display Time], the [Front Cover] settings only appear when the front cover sheet function is selected.

  • You can specify the [Apply Duplex] settings only when [At Mode Selected] is selected for [Display Time].

  • On the standard application screen, a lock icon (Operation panel screen illustration) is displayed against the paper tray for which [Display Time] is set to [Full Time].

Back Cover (Back Cover Sheet Tray)

You can specify and display the paper tray in which to load back cover sheets.

You can also specify the display time and copying method for duplex copying.

  • Tray to Program

    • Tray 1

    • Tray 2

    • Tray 3

    • Tray 4

    • Tray 5

    • Tray 6

    • Tray 7

    • Tray 8

    • Tray A

    • Intpsr. Upper (when the interposer is installed.)

    • Intpsr. Lower (when the interposer is installed.)

    Default: Off (Tray is not specified.)

  • Apply Duplex

    • Yes

    • No

    Default: [No]

  • Display Time

    • At Mode Selected

    • Full Time

    Default: [At Mode Selected]

Note

  • When you select an interposer tray, you cannot change the [Display Time] and [Apply Duplex] settings.

  • When [At Mode Selected] is selected for [Display Time], the [Back Cover] settings only appear when the back cover sheet function is selected.

  • You can specify the [Apply Duplex] settings only when [At Mode Selected] is selected for [Display Time].

  • On the standard application screen, a lock icon (Operation panel screen illustration) is displayed against the paper tray for which [Display Time] is set to [Full Time].

Slip Sheet (Slip Sheet Tray)

You can specify and display the paper tray in which to load slip sheets.

You can also specify the display time.

  • Tray to Program

    • Tray 1

    • Tray 2

    • Tray 3

    • Tray 4

    • Tray 5

    • Tray 6

    • Tray 7

    • Tray 8

    • Tray A

    Default: Off (Tray is not specified.)

  • Display Time

    • At Mode Selected

    • Full Time

    Default: [At Mode Selected]

Note

  • When [At Mode Selected] is selected for [Display Time], the [Slip Sheet] settings only appear when the slip sheet function is selected.

  • On the standard application screen, a lock icon (Operation panel screen illustration) is displayed against the paper tray for which [Display Time] is set to [Full Time].

Sep. Sheet (Separation Sheet Tray)

You can specify and display the paper tray in which to load separation sheets.

You can also specify the display time.

  • Tray to Program

    • Tray 1

    • Tray 2

    • Tray 3

    • Tray 4

    • Tray 5

    • Tray 6

    • Tray 7

    • Tray 8

    • Tray A

    • Intpsr. Upper (when the interposer is installed.)

    • Intpsr. Lower (when the interposer is installed.)

    Default: Off (Tray is not specified.)

  • Display Time

    • At Mode Selected

    • Full Time

    Default: [At Mode Selected]

Note

  • When you select an interposer tray, you cannot change the [Display Time] setting.

  • When [At Mode Selected] is selected for [Display Time], the [Sep. Sheet] settings only appear when the separation sheet function is selected.

  • On the standard application screen, a lock icon (Operation panel screen illustration) is displayed against the paper tray for which [Display Time] is set to [Full Time].

Desig. Sheet 1–11 (Designation Sheet 1–11 Tray)

You can specify and display the paper tray in which to load designation sheets.

You can also specify the display time and copying method for duplex copying.

  • Tray to Program

    • Tray 1

    • Tray 2

    • Tray 3

    • Tray 4

    • Tray 5

    • Tray 6

    • Tray 7

    • Tray 8

    • Tray A

    • Intpsr. Upper (when the interposer is installed.)

    • Intpsr. Lower (when the interposer is installed.)

    Default: Off (Tray is not specified.)

  • Apply Duplex

    • Yes

    • No

    Default: [Yes]

  • Display Time

    • At Mode Selected

    • Full Time

    Default: [At Mode Selected]

Note

  • When you select an interposer tray, you cannot change the [Display Time] and [Apply Duplex] settings.

  • When [At Mode Selected] is selected for [Display Time], the [Desig. Sheet 1–11] settings only appear when the designation sheet function is selected.

  • You can specify the [Apply Duplex] settings only when [At Mode Selected] is selected for [Display Time].

  • On the standard application screen, a lock icon (Operation panel screen illustration) is displayed against the paper tray for which [Display Time] is set to [Full Time].