Previous
This section describes the user tools in the Input / Output menu under [Copier / Document Server Features].
SADF Auto Reset
In SADF mode, an original must be placed within a specified time after the previous original has been fed.
Default: [5 second(s)]
You can adjust this time from 3 to 99 seconds in increments of 1 second.
Copy Eject Face Method in Glass Mode
You can select the way in which copies are delivered when copying an original placed on the exposure glass.
Default: [Face Up]
Memory Full Auto Scan Restart
When memory becomes full while scanning originals, the machine can make copies of scanned originals first, and then automatically proceed scanning remaining originals.
Default: [Off]
On
You can leave the machine unattended to make copies, but sorted pages will not be sequential.
Off
When memory becomes full, the machine stops operation allowing you to remove the copy pages delivered on the output tray.
Sort / Stack Shift Tray Setting
You can specify whether to shift the shift tray in Sort mode or Stack mode.
Default: [On]
Insert Separation Sheet
You can specify the number of copy pages for inserting the separation sheet from 1 to 999 pages in increments of 1 page.
Default: [1 set(s)]
Letterhead Setting
If you select [Yes] in this function, the machine rotates the image correctly.
Default: [No]
Orientation-fixed (top to bottom) or two-sided paper might not be printed correctly depending on how the originals and paper are placed. For details, see Loading Orientation-fixed Paper or Two-sided Paper.
Fore Edge Cut Setting
Specify the length of the fore edge cut.
Specify the cut length from 2.0 to 20.0 mm (0.08 to 0.79 inches) in increments of 1 mm (0.01 inches). In case of B5 JIS size paper, the cut length is between 2.0 to 10.0 mm.
Default:
(mainly Europe and Asia)
[4.0 mm]
(mainly North America)
[0.16 inch]
Staple Position
Specify which staple type has priority to be shown on the initial screen.
When Finisher SR5050/SR5110 is installed:
Default for "Staple Position 1": [Staple: Slant]
Default for "Staple Position 2": [Staple: Bottom 1]
Default for "Staple Position 3": [Staple: Left 2]
Default for "Staple Position 4": [Staple: Top 2]
When Booklet Finisher SR5060/SR5120 is installed:
Default for "Staple Position 1": [Staple: Slant]
Default for "Staple Position 2": [Staple: Center]
Default for "Staple Position 3": [Staple: Left 2]
Default for "Staple Position 4": [Staple: Top 2]
Punch Type
Specify which punch type has priority to be shown on the initial screen.
When 2 & 4 hole punch unit is installed:
Default for "Punch Type 1": [Punch: Left 2]
Default for "Punch Type 2": [Punch: Top 2]
When 2 & 3 hole punch unit is installed:
Default for "Punch Type 1": [Punch: Left 3]
Default for "Punch Type 2": [Punch: Top 3]
Ring Binding/Fold Type/Stacker Output Tray
You can specify which ring binding types, fold types, and stacker tray have priority on the initial screen.
Item names, displayed items, and defaults differ depending on which options are installed.
Finisher: Staple Position
Specify the stapling position.
Default for "Finisher: Staple Position 1": [Off]
Default for "Finisher: Staple Position 2": [Off]
Default for "Finisher: Staple Position 3": [Off]
Default for "Finisher: Staple Position 4": [Off]
Finisher: Punch Type
Specify the punch type.
Default for "Finisher: Punch Type 1": [Off]
Default for "Finisher: Punch Type 2": [Off]
Default for "Finisher: Punch Type 3": [Off]
Default for "Finisher: Punch Type 4": [Off]
Finisher: Ring Binding Type
You can specify which ring binding types have priority.
Default for "Finisher: Ring Binding Type 1": [Off]
Default for "Finisher: Ring Binding Type 2": [Off]
Default for "Finisher: Ring Binding Type 3": [Off]
Default for "Finisher: Ring Binding Type 4": [Off]
Simplified Screen: Finishing Types
You can select which key is displayed with higher priority for "Finishing Types" on the simple screen.
Default for "Simplified Screen: Finishing Types 1": [Do not Display]
Default for "Simplified Screen: Finishing Types 2": [Do not Display]
Default for "Simplified Screen: Finishing Types 3": [Do not Display]
Half Fold Settings (Finisher: Booklet Tray)
Specify each settings of half fold.
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
Default: [Off]
Z-fold Output Tray
Specify the tray where Z-fold prints are output to.
Default: [Folding Unit Tray]
Half Fold Settings
Specify each settings of half fold.
Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
Default: [Off]
Letter Fold-out Settings
Specify each settings of letter fold-out.
Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Open Orientation
Specify the opening orientation of prints.
Default: [Open to Right]
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
Default: [Off]
Letter Fold-in Settings
Specify each settings of letter fold-in.
Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Open Orientation
Specify the opening orientation of prints.
Default: [Open to Right]
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
Default: [Off]
Double Parallel Fold Settings
Specify each settings of double parallel fold.
Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Open Orientation
Specify the opening orientation of prints.
Default: [Open to Right]
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
Gate Fold Settings
Specify each settings of gate fold.
Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
For details about how to change the Copier / Document Server Features, see "Accessing User Tools", Device Management.
