Previous
This section describes recommended paper sizes and types.
If you use paper that curls, either because it is too dry or too damp, a staple clogging or paper jam may occur.
Do not use paper designed for inkjet printers, as these may stick to the fusing unit and cause a misfeed.
When you load OHP transparencies, check the front and back of the sheets, and place them correctly, or a misfeed might occur.
Tray 1
Paper type and weight |
Paper size |
Paper capacity |
|---|---|---|
60–300 g/m2 (16 lb. Bond–110 lb. Cover) Plain Paper 1–Thick Paper 4 |
A4
81/2 × 11 |
550 sheets |
60–300 g/m2 (16 lb. Bond–110 lb. Cover) Plain Paper 1–Thick Paper 4 |
*1
A5
A4 |
550 sheets |
*1 To load paper any of the sizes specified above, contact your service representative.
Tray 2
Paper type and weight |
Paper size |
Paper capacity |
|---|---|---|
60–300 g/m2 (16 lb. Bond–110 lb. Cover) Plain Paper 1–Thick Paper 4 |
Paper sizes that can be detected automatically*1:
A3
A4 |
550 sheets |
60–300 g/m2 (16 lb. Bond–110 lb. Cover) Plain Paper 1–Thick Paper 4 |
Select the paper size using the Tray Paper Settings menu*1:
A5 8 × 10
A3 71/4 × 101/2 |
550 sheets |
60–300 g/m2 (16 lb. Bond–110 lb. Cover) Plain Paper 1–Thick Paper 4 |
Custom size*2, 3:
Vertical: 90.0–320.0 mm Horizontal: 148.0–457.2 mm
Vertical: 3.55–12.59 inches Horizontal: 5.83–18.00 inches |
550 sheets |
Envelopes |
Select the paper size using the Tray Paper Settings menu: 41/8 × 91/2 |
|
*1 Adjust the supporting side fence before loading B4 JIS
, A3, SRA3, 11 × 17, or 12 × 18 paper.
*2 Set the supporting side fence position to SRA3 before loading paper with a vertical length of 297 mm or longer and a horizontal length of over 335 mm.
*3 When loading paper with a vertical length of more than 304.8 mm (12.0 inches) in Trays 2–4, use paper that has a horizontal width of 450 mm (17.8 inches) or less.
Trays 3 and 4
Paper type and weight |
Paper size |
Paper capacity |
|---|---|---|
60–300 g/m2 (16 lb. Bond–110 lb. Cover) Plain Paper 1–Thick Paper 4 |
Paper sizes that can be detected automatically*1:
A3
A4 |
550 sheets |
60–300 g/m2 (16 lb. Bond–110 lb. Cover) Plain Paper 1–Thick Paper 4 |
Select the paper size using the Tray Paper Settings menu*1:
A5 11 × 17 71/4 × 101/2
A3 81/2 × 13 71/4 × 101/2 |
550 sheets |
60–300 g/m2 (16 lb. Bond–110 lb. Cover) Plain Paper 1–Thick Paper 4 |
Custom size*3, 4:
Vertical: 90.0–320.0 mm Horizontal: 148.0–457.2 mm
Vertical: 3.55–12.59 inches Horizontal: 5.83–18.00 inches |
550 sheets |
Envelopes |
Select the paper size using the Tray Paper Settings menu: 41/8 × 91/2 |
|
*1 Adjust the supporting side fence before loading B4 JIS, A3, SRA3, 11 × 17, or 12 × 18 paper.
*2 There are lines to indicate these paper sizes on the labels attached to the paper trays, however there is no size description for these paper sizes.
*3 When loading paper with a vertical length of more than 304.8 mm (12.0 inches) in Trays 2–4, use paper that has a horizontal width of 450 mm (17.8 inches) or less.
*4 Set the supporting side fence position to SRA3 before loading paper with a vertical length of 297 mm or longer and a horizontal length of over 335 mm.
Bypass tray
Paper type and weight |
Paper size |
Paper capacity |
|---|---|---|
52–300 g/m2 (14 lb. Bond–110 lb. Cover) Thin Paper–Thick Paper 4 |
Paper sizes that can be detected automatically:
A3
A5 |
|
52–300 g/m2 (14 lb. Bond–110 lb. Cover) Thin Paper–Thick Paper 4 |
*1
11 × 17 71/4 × 101/2
A3 71/4 × 101/2 |
|
52–300 g/m2 (14 lb. Bond–110 lb. Cover) Thin Paper–Thick Paper 4 |
Custom size*2:
Vertical: 90.0–320.0 mm Horizontal: 148.0–457.2 mm *3
Vertical: 3.55–12.59 inches Horizontal: 5.83–18.00 inches*3 |
|
OHP transparencies |
A4 |
50 sheets |
Translucent paper |
A3 |
1 sheet |
Label paper (adhesive labels) |
B4 JIS |
30 sheets |
Envelopes |
*1 41/8 × 91/2 |
10 sheets |
*1 Select the paper size. For copier mode, see "Copying from the Bypass Tray", Copy/ Document Server. For printer mode, see Specifying regular sizes using the control panel.
*2 Enter the paper size. For copier mode, see "Copying from the Bypass Tray", Copy/ Document Server. For printer mode, see Specifying a custom size paper using the control panel.
*3 In printer or facsimile mode, the maximum horizontal length of the custom size is 1,260 mm (49.60 inches). If you want to print on paper with a horizontal length of 600–1,260 mm (23.62–49.60 inches), contact your service representative. If you want to load paper with a horizontal length of 600 mm (23.62 inches) or longer in the bypass tray, it must have a vertical width of 305 mm (12.1 inches) or less.
Tray 3 (LCT)
Paper type and weight |
Paper size |
Paper capacity |
|---|---|---|
52–300 g/m2 (14 lb. Bond–110 lb. Cover) Thin Paper–Thick Paper 4 |
A4
81/2 × 11 |
1000 sheets × 2 |
52–300 g/m2 (14 lb. Bond–110 lb. Cover) Thin Paper–Thick Paper 4 |
*1
81/2 × 11
A4 |
1000 sheets × 2 |
*1 To load paper any of the sizes specified above, contact your service representative.
Large capacity tray (LCT)
Paper type and weight |
Paper size |
Paper capacity |
|---|---|---|
52–300 g/m2 (14 lb. Bond–110 lb. Cover) Thin Paper–Thick Paper 4 |
A4
81/2 × 11 |
1500 sheets |
52–300 g/m2 (14 lb. Bond–110 lb. Cover) Thin Paper–Thick Paper 4 |
*1
B5 JIS
A4 |
1500 sheets |
*1 To load paper any of the sizes specified above, contact your service representative.
Paper Thickness
Paper Thickness*1 |
Paper weight |
|---|---|
Thin Paper*2 |
52–59 g/m2 (14–15 lb. Bond) |
Plain Paper 1 |
60–74 g/m2 (16–20 lb. Bond) |
Plain Paper 2 |
75–81 g/m2 (20 lb. Bond) |
Middle Thick |
82–105 g/m2 (20–28 lb. Bond) |
Thick Paper 1 |
106–169 g/m2 (28 lb. Bond–90 lb. Index) |
Thick Paper 2 |
170–220 g/m2 (65–80 lb. Cover) |
Thick Paper 3 |
221–256 g/m2 (80 lb. Cover–140 lb. Index) |
Thick Paper 4 |
257–300 g/m2 (140 lb. Index–110 lb. Cover) |
*1 Print quality will decrease if the paper you are using is close to the minimum or maximum weight. Change the paper weight setting to thinner or thicker.
*2 Depending on the type of thin paper, the edges may crease or the paper may be misfed.
Certain types of paper, such as translucent paper or OHP transparencies, may produce noise when delivered. This noise does not indicate a problem and print quality is unaffected.
The paper capacity described in the tables above is an example. Actual paper capacity might be lower, depending on the paper type.
When loading paper, make sure the stack height does not exceed the limit mark of the paper tray.
If multiple sheet feeding occurs, fan sheets thoroughly or load sheets one by one from the bypass tray.
Flatten out curled sheets before loading them.
Depending on the paper sizes and types, the copy/print speed may be slower than usual.
When loading thick paper of 106–300 g/m2 (28 lb. Bond–110 lb. Cover), see Thick paper.
When loading envelopes, see Envelopes.
When copying or printing onto letterhead paper, the paper placing orientation is different depending on which function you are using. For details, see Loading Orientation-fixed Paper or Two-sided Paper.
If you load paper of the same size and same type in two or more trays, the machine automatically feeds from one of the trays in which [Yes] is selected for [Apply Auto Paper Select] when the first tray in use runs out of paper. This function is called Auto Tray Switching. This saves interrupting a copy run to replenish paper when making a large number of copies. You can specify the paper type of the paper trays under [Paper Type]. For details, see "Tray Paper Settings", Connecting the Machine/ System Settings. For the setting procedure of the Auto Tray Switching function, see "General Features", Copy/ Document Server.
When loading label paper:
We recommend that you use specified label paper.
It is recommended to place one sheet at a time.
Press [Bypass], and then select the appropriate paper thickness for [Paper Type].
When loading OHP transparencies:
It is recommended to place one sheet at a time.
When copying onto OHP transparencies, see "Copying onto OHP Transparencies", Copy/ Document Server.
When printing on OHP transparencies from the computer, see Specifying thick paper, thin paper, or OHP transparencies for paper type using the control panel.
Fan OHP transparencies thoroughly whenever you use them. This prevents OHP transparencies from sticking together, and from feeding incorrectly.
Remove copied or printed sheets one by one.
When loading translucent paper:
When loading translucent paper, always use long grain paper, and set the paper direction according to the grain.
Translucent paper easily absorbs humidity and becomes curled. Remove curl in the translucent paper before loading.
Remove copied or printed sheets one by one.
When loading coated paper:
To print on coated paper: press the [User Tools] icon (
), press [Tray Paper Settings], and then, for each tray's [Paper Type] be sure to specify [Paper Type] to [Coated: Matte], and [Paper Thickness] to the appropriate paper thickness.To print on high-gloss coated paper: press the [User Tools] icon (
), press [Tray Paper Settings], and then, for each tray's [Paper Type], be sure to set [Paper Type] to [Coated: Glossy].When loading coated paper or glossy paper, always fan the paper before using it.
If a paper jam occurs or if the machine makes a strange noise when feeding stacks of coated paper, feed the coated paper from the bypass tray one sheet at a time.
After continuous printing of A5
, A6, envelopes or other smaller custom paper sizes, printing on different sized paper may require a wait of up to 1 minute for adjustments.
