Previous
This section describes the user tools in the Input / Output menu under [Copier / Document Server Features].
Switch to Batch
You can select to have Batch mode or SADF mode displayed when you press [Original Settings].
Default: [Batch]
SADF Auto Reset
In SADF mode, an original must be placed within a specified time after the previous original has been fed.
Default: [5 second(s)]
You can adjust this time from 3 to 99 seconds in increments of 1 second.
Rotate Sort: Auto Paper Continue
Specify whether or not the machine continues copying when paper of the required orientation runs out during rotate sort.
Default: [Off]
On
Copying continues using copy paper of a different orientation. The copy job will finish even if you have left the machine.
Off
When paper of the required orientation runs out, the machine stops copying and prompts you to supply copy paper. After you have loaded paper, the machine will continue copying.
Memory Full Auto Scan Restart
When memory becomes full while scanning originals, the machine can make copies of scanned originals first, and then automatically proceed scanning remaining originals.
Default: [Off]
On
You can leave the machine unattended to make copies, but sorted pages will not be sequential.
Off
When memory becomes full, the machine stops operation allowing you to remove the copy pages delivered on the output tray.
Letterhead Setting
If you select [Yes] in this function, the machine rotates the image correctly.
Default: [No]
Orientation-fixed (top to bottom) or two-sided paper might not be printed correctly depending on how the originals and paper are placed. For details, see "Loading Orientation-fixed Paper or Two-sided Paper", Paper Specifications and Adding Paper.
Stapleless Position
Specify whether or not to display the staple-free staple button on the initial screen when Finisher SR3210 is installed.
When you select [Stpless. Stplr.], the staple-free staple button is displayed.
Default: [Stpless. Stplr.]
Staple Position
Specify which staple type has priority to be shown on the initial screen.
When Internal Finisher SR3130 is installed:
Default for "Staple Position 1": [Staple: Top 1]
Default for "Staple Position 2": [Staple: Bottom 1]
Default for "Staple Position 3": [Staple: Left 2]
Default for "Staple Position 4": [Staple: Top 2]
When Finisher SR3210 is installed:
Default for "Staple Position 1": [Staple: Top 1]
Default for "Staple Position 2": [Staple: Left 2]
Default for "Staple Position 3": [Staple: Top 2]
When Booklet Finisher SR3220 is installed:
Default for "Staple Position 1": [Staple: Top 1]
Default for "Staple Position 2": [Staple: Center]
Default for "Staple Position 3": [Staple: Left 2]
Default for "Staple Position 4": [Staple: Top 2]
When Finisher SR3230 is installed:
Default for "Staple Position 1": [Staple: Slant]
Default for "Staple Position 2": [Staple: Bottom 1]
Default for "Staple Position 3": [Staple: Left 2]
Default for "Staple Position 4": [Staple: Top 2]
When Booklet Finisher SR3240 is installed:
Default for "Staple Position 1": [Staple: Slant]
Default for "Staple Position 2": [Staple: Center]
Default for "Staple Position 3": [Staple: Left 2]
Default for "Staple Position 4": [Staple: Top 2]
When Internal Finisher SR3180 is installed:
Default for "Staple Position 1": [Staple: Slant]
Default for "Staple Position 2": [Off]
Default for "Staple Position 3": [Off]
Default for "Staple Position 4": [Off]
Punch Type
Specify which punch type has priority to be shown on the initial screen.
When 2 & 4 hole punch unit is installed:
Default for "Punch Type 1": [Punch: 2 Holes Left]
Default for "Punch Type 2": [Punch: 2 Holes Top]
When 2 & 3 hole punch unit is installed:
Default for "Punch Type 1": [Punch: 3 Holes Left]
Default for "Punch Type 2": [Punch: 3 Holes Top]
Simplified Screen: Finishing Types
You can select which key is displayed with higher priority for "Finishing Types" on the simple screen.
Default for "Simplified Screen: Finishing Types 1": [Do not Display]
Default for "Simplified Screen: Finishing Types 2": [Do not Display]
Default for "Simplified Screen: Finishing Types 3": [Do not Display]
Z-fold/Half Fold Output Tray
Specify the tray where Z-fold and Half fold prints are output to.
When either Finisher SR3230 or Booklet Finisher SR3240 is installed, and Internal Multi-Folding unit is also installed.
Default: [Finisher Shift Tray]
When either Finisher SR3210 or Booklet Finisher SR3220 is installed, and Internal Multi-Folding unit is also installed.
Default: [Finisher Upper Tray]
Half Fold Settings
Specify each settings of half fold.
Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
Letter Fold-out Settings
Specify each settings of letter fold-out.
Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Open Orientation
Specify the opening orientation of prints.
Default: [Open to Right]
Letter Fold-in Settings
Specify each settings of letter fold-in.
Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Open Orientation
Specify the opening orientation of prints.
Default: [Open to Right]
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
For details about how to change the Copier / Document Server Features, see "Accessing User Tools", Connecting the Machine/ System Settings.
