Skip header
 

General Features

This section describes the user tools in the General Features menu under System Settings.

Program / Change / Delete User Text

You can register text phrases you often use when specifying settings, such as ".com" and "Regards".

You can register up to 40 entries.

  • Program / Change

    1. Press [Home] (Operation panel screen illustration) at the bottom of the screen in the center.

    2. Flick the screen to the left, and then press the [User Tools] (Operation panel screen illustration) icon.

    3. Press [Machine Features].

    4. Press [System Settings].

    5. Check that [General Features] is selected.

    6. Press [Program / Change / Delete User Text].

    7. Check that [Program / Change] is selected.

    8. Select the user text you want to change.

      To program a new user text, press [*Not Programmed].

    9. Enter the user text, and then press [OK].

      Enter the user text up to 80 characters.

    10. Press [Exit].

    11. Press [User Tools] (Operation panel screen illustration) on the top right of the screen.

    12. Press [Home] (Operation panel screen illustration) at the bottom of the screen in the center.

  • Delete

    1. Press [Home] (Operation panel screen illustration) at the bottom of the screen in the center.

    2. Flick the screen to the left, and then press the [User Tools] (Operation panel screen illustration) icon.

    3. Press [Machine Features].

    4. Press [System Settings].

    5. Check that [General Features] is selected.

    6. Press [Program / Change / Delete User Text].

    7. Press [Delete].

    8. Select the user text you want to delete.

    9. Press [Yes].

    10. Press [Exit].

    11. Press [User Tools] (Operation panel screen illustration) on the top right of the screen.

    12. Press [Home] (Operation panel screen illustration) at the bottom of the screen in the center.

Screen Color Setting

You can change the screen color.

Default: [Blue-gray]

This setting is applied to [Printer (Classic)] screen.

Output: Printer

Specify a tray to which documents are delivered.

Default: [Internal Tray 1]

Key Repeat

You can enable or disable repetition of an operation if a key on the screen or control panel is pressed continuously.

Default: [Normal]

The key repeat function is available only on [Printer (Classic)] screen.

Measurement Unit

You can switch the measurement between [mm] and [inch] when you specify a custom size on the control panel.

RegionA icon(mainly Europe and Asia)

Default: [mm]

RegionB icon(mainly North America)

Default: [inch]

System Status/Job List Display Time

Specify how long to display the System Status and Job List display for.

Default: [On], [15 second(s)]

When the setting is [On], you can specify a display time between 10 and 999 seconds in steps of 1 second using the number keys.

Z-fold Position (When Internal Multi-fold unit is installed)

If you specify Z-folding, set the fold-back position in 0.5 mm (0.02") increments. The setting ranges of the folding position for each paper size are shown below:

Metric version:

  • A3: 2 - 25 mm

  • B4 JIS: 2 - 17 mm

  • A4: 2 - 17 mm

  • 11 × 17: 2 - 20 mm

  • 81/2 × 14: 2 - 17 mm

  • 81/2 × 11: 2 - 17 mm

  • 8K: 2 - 17 mm

  • 81/2 × 132/5: 2 - 17 mm

  • Other Paper Sizes: 2 - 17 mm

Inch version:

  • A3: 0.08" - 1.00"

  • B4 JIS: 0.08" - 0.68"

  • A4: 0.08" - 0.68"

  • 11 × 17: 0.08" - 0.80"

  • 81/2 × 14: 0.08" - 0.68"

  • 81/2 × 11: 0.08" - 0.68"

  • 8K: 0.08" - 0.68"

  • 81/2 × 132/5: 0.08" - 0.68"

  • Other Paper Sizes: 0.08" - 0.68"

Half Fold Position (When Internal Multi-fold unit is installed)

If you specify half folding, set the fold-back position in 0.1 mm (0.004") increments. The setting ranges of the folding position for each paper size are shown below:

Metric version:

  • A3: -10 - 10 mm

  • B4 JIS: -10 - 10 mm

  • A4: -10 - 10 mm

  • 11 × 17: -10 - 10 mm

  • 81/2 × 14: -10 - 10 mm

  • 81/2 × 11: -10 - 10 mm

  • 8K: -10 - 10 mm

  • 12 × 18: -5.0 – 5.0 mm

  • 81/2 × 132/5: -10 - 10 mm

  • Other Paper Sizes: -10 - 10 mm

Inch version:

  • A3: -0.40" - 0.40"

  • B4 JIS: -0.40" - 0.40"

  • A4: -0.40" - 0.40"

  • 11 × 17: -0.40" - 0.40"

  • 81/2 × 14: -0.40" - 0.40"

  • 81/2 × 11: -0.40" - 0.40"

  • 8K: -0.40" - 0.40"

  • 12 × 18: -0.20" - 0.20"

  • 81/2 × 132/5: -0.40" - 0.40"

  • Other Paper Sizes: -0.40" - 0.40"

External Keyboard

You can specify the layout for an external keyboard which is connected to the USB Host Interface port.

Default: [Off]

The following languages can be set:

RegionA icon (mainly Europe)

[English], [German], [Standard French], [Belgian French], [Canadian French], [Italian], [Spanish], [Dutch], [Portuguese], [Polish], [Czech], [Swedish], [Finnish], [Hungarian], [Norwegian], [Danish], [Japanese], [Simplified Chinese], [Traditional Chinese], [Russian], [Hangul], [Catalan], [Turkish], and [Greek]

RegionA icon (mainly Asia)

[English], [German], [Canadian French], [Italian], [Spanish], [Dutch], [Portuguese], [Polish], [Czech], [Swedish], [Finnish], [Hungarian], [Norwegian], [Danish], [Japanese], [Simplified Chinese], [Traditional Chinese], [Russian], [Hangul], [Catalan], and [Turkish]

RegionB icon (mainly North America)

[English], [German], [Canadian French], [Italian], [Spanish], [Dutch], [Portuguese], [Polish], [Czech], [Swedish], [Finnish], [Hungarian], [Norwegian], [Danish], [Japanese], [Simplified Chinese], [Traditional Chinese], [Russian], [Hangul], [Catalan], and [Turkish]

Compatible ID

You can enable or disable the Compatible ID setting.

If this setting is set to [Active], you can install the printer driver automatically by connecting a computer to the machine via USB or network.

Default: [Active]

Program/Change USB Device List

You can register "Product ID" and "Vendor ID" information for a USB keyboard or IC card reader device to the device list to limit the usage of USB devices. The "Product ID" and "Vendor ID" information for a USB device have been assigned by the manufacturer to identify the individual device. "Product ID" input settings are between 0 and 0xFFFF. "Vendor ID" input settings are between 0x0001 and 0xFFFE. Up to ten pairs of "Product ID" and "Vendor ID" information can be registered.

Erase Margin for Stapleless Stapler (When Finisher SR3210 is installed)

Default: [Off]

The staple may come off easily if the stapleless stapler is applied to an image printed in a stapling position.

To prevent this, you can specify a binding margin to adjust the image position with [Margin Adj.].

Enable this function only when erasing the image around the position to be stapled is acceptable.

Stapling Method for Stapleless Stapler (When Finisher SR3210 is installed)

Select either [Single] or [Double] as the stapling method for the stapleless stapler. The Single setting is faster, and the Double setting has better retention capability.

Default: [Double]

Auto Switch Staple/Stapleless Stapler (When Finisher SR3210 is installed)

Specify whether to use staples or stapleless to fasten documents together when you print six or more sheets of paper. This setting is applied when you select stapleless as the method to fasten documents together from the control panel or printer driver.

If [Off] is selected, every five sheets of paper are stapled without staples. If [On] is selected and there are fewer than 50 pages printed, they are stapled with staples. If there are more than 50 pages printed, they are not stapled.

Default: [Off]

Output Priority When Paper is Fed to Finisher

You can choose whether to give priority to the time to recover from Energy Saver mode or to the print speed when you feed paper to the finisher. If [Print Start Time] is selected, the number of pages printed is less than in the normal state shortly after recovering from Energy Saver mode. However, the time to start printing is reduced.

Default: [Print Start Time]

Energy Saving Recvry. for Business Applicatn.

Specify whether or not to enable low-energy recovery from Sleep mode to use applications independent of the machine, such as Address Book Management or Browser.

Default: [Off]

If [On (Energy Saving)] is selected, it takes longer than usual to be ready to use the machine.

Low Paper Indicator (Yellow Flashing)

Specify whether or not to indicate that paper runs out.

  • Active

  • Inactive

Default: [Inactive]

Letter Fold-out Position 1 (When Internal Multi-fold unit is installed)

Set the end folding position for each paper size when outside three-fold is performed. If you specify half folding, set the fold-back position in 0.5 mm (0.02") increments.

The setting ranges of the folding position for each paper size are shown below:

Metric version:

  • A3: 2 - 10 mm

  • 11 × 17: 2 - 10 mm

  • A4: 2 - 10 mm

  • 81/2 × 14: 2 - 10 mm

  • 81/2 × 11: 2 - 10 mm

  • 81/2 × 132/5: 2-10 mm

  • Other Paper Sizes: 2 - 10 mm

Inch version:

  • A3: 0.08" - 0.40"

  • 11 × 17: 0.08" - 0.40"

  • A4: 0.08" - 0.40"

  • 81/2 × 14: 0.08" - 0.40"

  • 81/2 × 11: 0.08" - 0.40"

  • 81/2 × 132/5: 0.08" - 0.40"

  • Other Paper Sizes: 0.08" - 0.40"

Letter Fold-out Position 2 (When Internal Multi-fold unit is installed)

Set the outer frame folding position for each paper size when outside three-fold is performed. If you specify half folding, set the fold-back position in 0.5 mm (0.02") increments.

The setting ranges of the folding position for each paper size are shown below:

Metric version:

  • A3: 139.0 - 147.0 mm

  • 11 × 17: 143.0 - 151.0 mm

  • A4: 98.0 - 106.0 mm

  • 81/2 × 14: 117.5 - 125.5 mm

  • 81/2 × 11: 92.0 - 100.0 mm

  • 81/2 × 132/5: 112.5-120.5 mm

  • Other Paper Sizes: 89.0 - 155.5 mm

Inch version:

  • A3: 5.48" - 5.80"

  • 11 × 17: 5.64" - 5.96"

  • A4: 3.84" - 4.16"

  • 81/2 × 14: 4.62" - 4.94"

  • 81/2 × 11: 3.60" - 3.92"

  • 81/2 × 132/5: 4.42" - 4.74"

  • Other Paper Sizes: 3.48" - 6.14"

Letter Fold-in Position 1 (When Internal Multi-fold unit is installed)

Set the end folding for each paper size when inner three-fold is performed. If you specify half folding, set the fold-back position in 0.5 mm (0.02") increments.

The setting ranges of the folding position for each paper size are shown below:

Metric version:

  • A3: 3.0 - 9.0 mm

  • 11 × 17: 3.0 - 9.0 mm

  • A4: 3.0 - 9.0 mm

  • 81/2 × 14: 3.0 - 9.0 mm

  • 81/2 × 11: 3.0 - 9.0 mm

  • 81/2 × 132/5: 3.0 - 9.0 mm

  • Other Paper Sizes: 3.0 - 9.0 mm

Inch version:

  • A3: 0.12" - 0.36"

  • 11 × 17: 0.12" - 0.36"

  • A4: 0.12" - 0.36"

  • 81/2 × 14: 0.12" - 0.36"

  • 81/2 × 11: 0.12" - 0.36"

  • 81/2 × 132/5: 0.12" - 0.36"

  • Other Paper Sizes: 0.12" - 0.36"

Letter Fold-in Position 2 (When Internal Multi-fold unit is installed)

Set the outer frame folding position for each paper size when inner three-fold is performed. If you specify half folding, set the fold-back position in 0.5 mm (0.02") increments.

The setting ranges of the folding position for each paper size are shown below:

Metric version:

  • A3: 139.0 - 147.0 mm

  • 11 × 17: 143.0 - 151.0 mm

  • A4: 98.0 - 106.0 mm

  • 81/2 × 14: 117.5 - 125.5 mm

  • 81/2 × 11: 92.0 - 100.0 mm

  • 81/2 × 132/5: 112.5-120.5 mm

  • Other Paper Sizes: 89.0 - 155.5 mm

Inch version:

  • A3: 5.48" - 5.80"

  • 11 × 17: 5.64" - 5.96"

  • A4: 3.84" - 4.16"

  • 81/2 × 14: 4.62" - 4.94"

  • 81/2 × 11: 3.60" - 3.92"

  • 81/2 × 132/5: 4.42" - 4.74"

  • Other Paper Sizes: 3.48" - 6.14"

Note

Related topics

Output Tray Settings