System Log Information

account is unavailable:

encryption is impossible.

Encryption is not possible and account is disabled. This could be because:

• Security option is not installed.

• Encryption password has not been specified.

account is unavailable:

same account name be used.

User account is disabled. This could be because it uses the same account name as the administrator account.

account is unavailable:

The authentication password is not set up.

User account is disabled. This could be because the authentication password is not set, and only the encryption account is set.

add_sess_IPv4: bad trap addr: <IPv4 address>, community: <community name>

The IPv4 address (0.0.0.0) is unavailable when the community access type is TRAP. Specify the host IPv4 address for the TRAP destination.

add_sess_IPv4: community <community name> already defined.

The same community name already exists. Use another community name.

add_sess_IPv6: bad trap addr: <IPv6 address>, community: <community name>

The IPv6 address [::] is unavailable when the community access type is TRAP. Specify the host IPv6 address for the TRAP destination.

add_sess_IPv6: community <community name> already defined.

The same community name already exists. Use another community name.

adjust time server <NTP server name> offset: xx sec.

ncsd tells you the timing of the NTP server and whether or not the time system clock is set.

NTP Server: NTP server name

offset: number of seconds of delay (minus number if a time in advance is specified)

Attach FileServer=<file server>

Connection to the file server as the nearest server has been established.

Attach to print queue <print queue name>

The system connects to the print queue when the print server goes online.

authenticated

The supplicant is authenticated. This message indicates that the supplicant is successfully authenticated. If the authentication is successful, this message always appears.

authenticating

The supplicant is being authenticated via EAP or WPA.

centrod is disabled.

Communication via Bluetooth is unavailable because btd is disabled in the security mode.

Enable btd in the security mode.

child process exec error ! (process name)

Parallel communication could not be established.

Enable centrod in the Security Mode setting.

client EAP method rejected

The network service failed to start. Turn the machine off and then on. If this does not work, contact your service or sales representative.

client password rejected

The RADIUS server rejected the EAP method selected by the supplicant.

client TLS certificate rejected

The user name or password is not correct.

• For LEAP, the user name or password is not correct.

• For TTLS/PEAP, the phase 2 user name or phase 2 password is not correct.

Connected DHCP server <DHCP server address>

The RADIUS server rejected the client's TLS certificate.

Connected DHCPv6 server <IPv6 address>

The IP address was successfully received from the DHCP server.

connecting

The IP address was successfully received from the DHCPv6 server.

connection from <IP address>

The supplicant is establishing a wireless connection with an access point.

Could not attach to FileServer <error number>

A user logged in from the host <IP address>.

Could not attach to PServer <print server>

Connection to the file server could not be established when the remote printer went online. The file server refused the connection for unknown reason. Check the file server's configuration.

Current Interface Speed: xxx Mbps

Connection to the print server has not been established when the remote printer is turned on. The print server has refused the connection. Check the print server configuration.

Current IP address (<current IP address>)

Speed of the network (10Mbps, 100 Mbps, or 1Gbps).

DHCP lease time expired.

The IP address <current IP address> was acquired from the DHCP server.

DHCP server not found.

The DHCP lease time has expired. Perform the DHCP discover again. The IP address you have been using is no longer available.

DHCPv 6 address LeaseTime expired

The DHCP server was not found. Make sure that the DHCP is on the network.

DHCPv 6 address not leased (StatusCode = <status code>)

The lease time of DHCPv6 address has expired. Obtain IPv6 address from DHCPv6 server again. The IPv6 address you have been using is no longer available. Make sure that the DHCPv6 is on the network.

DHCPv 6 address RenewTime =<renew time>(sec), LeaseTime =<lease time>(sec)

For some reason, IPv6 address cannot be obtained from DHCPv6 server. Check the status code description.

<StatusCode>: This indicates the status of DHCPv6 message or option. The followings are the status codes when an error occurs.

UnspecFail(1): This indicates unknown reason error. This may appear when inappropriate option is included in a message.

NoAddrsAvail(2): This indicates that allocated IPv6 address does not exist.

NoBinding(3): This indicates that specified IPv6 address does not exist in designated IPv6 addresses.

NotOnLink(4): This indicates that specified prefix length for IPv6 address is invalid.

UseMulticast(5): This indicates that message needs to be sent using multicast.

DHCPv 6 client started

The time taken to require renewal of IPv6 address obtained from the DHCPv6 server is displayed in [renew time] in seconds. The expire time received from the DHCPv6 server is displayed in [lease time] in seconds.

When lease time elapses, the IPv6 address you have been using is no longer available.

DHCPv 6 client terminated

DHCPv6 client has started.

DHCPv 6 Parameter RefreshTime = <renew time>(sec)

DHCPv6 client has terminated.

DHCPv6 server not found

The time taken to require renewal of parameter obtained from the DHCPv6 server is displayed in [renew time] in seconds. Parameter is the information such as DNS server address and DNS search path other than DHCPv6 address.

disconnected

The DHCPv6 server was not found. Make sure that the DHCPv6 is on the network.

Duplicate IP=<IP address>(from <MAC address>).

The supplicant is disconnected.

Exit pserver

A conflicting IPv4 or IPv6 address was used. Each IPv4 or IPv6 address must be unique. Check the device address in [MAC address].

exiting

(In the print server mode) The print server function is disabled because the necessary print server settings have not been made.

httpd start.

The LPD service has completed and the process is exiting.

IEEE 802.11 Card does NOT support WPA.

The httpd has started.

IEEE 802.11 Card Firmware REV.<version>

IEEE 802.11 interface unit that does not support WPA is installed. Install an IEEE 802.11 interface unit that supports WPA.

IEEE 802.11 current channel <channel number>

Displays the version number of the IEEE 802.11 interface unit's firmware.

IEEE 802.11 MAC Address = <MAC address>

Displays the current channel number of the active IEEE 802.11 interface unit (in ad hoc and infrastructure mode).

IEEE 802.11 SSID <ssid> (AP MAC Address <MAC address>)

Displays the MAC address of the wireless interface.

IEEE 802.11 <communication mode> mode

The MAC address and SSID of the access point are connected in infrastructure mode.

(IKE phase-1) mismatched authentication type: local=<authentication type 1> remote=<authentication type 2>

Displays the IEEE 802.11 communication mode.

(IKE phase-1) mismatched encryption type: local=<encryption algorithm 1> remote=<encryption algorithm 2>

This machine's <authentication type 1> in IKE phase 1 does not match the communicating host's <authentication type 2>. Make sure this machine's ISAKMP SA authentication type matches that of the communicating host.

(IKE phase-1) mismatched DH group: local=<DH group number 1> remote=<DH group number 2>

This machine's ISAKMP SA Oakley group <encryption algorithm 1> in IKE phase 1 does not match the communicating host's ISAKMP SA Oakley group < encryption algorithm 2>. Make sure this machine's ISAKMP SA Oakley group matches that of the communicating host.

(IKE phase-1) mismatched hash type: local=<Hash Algorithm 1> remote=<Hash Algorithm 2>

This machine's ISAKMP SA Oakley group <DH group number 1> in IKE phase 1 does not match the communicating host's ISAKMP SA Oakley group <DH group number 2>. Make sure this machine's ISAKMP SA Oakley group matches that of the communicating host.

IKE [% s] is disable, set PSK text.

This machine's ISAKMP SA <Hash Algorithm 1> in IKE phase 1 does not match the communicating host's ISAKMP SA <Hash Algorithm 2>. Make sure this machine's ISAKMP SA Hash Algorithm matches that of the communicating host.

inetd start.

The specified IKE entry is invalid. Enter the PSK text.

Interface (interface name): Duplicate IP Address (<IP address>).

The inetd service has started.

< Interface > started with IP: < IP address >

The same IP (IPv4 or IPv6) address was used. Each IP address must be unique. Check the address of the device indicated in [IP address].

< Interface >: Subnet overlap.

IP address (IPv4 or IPv6 address) has been set for the interface and is operating.

<inferface name > card removed

The same IP address (IPv4, or IPv6 address) and the subnet mask are used with another device.

<inferface name > interface down

The supplicant's wireless LAN interface unit has been removed.

<inferface name > interface up

The supplicant's interface is invalid.

IPP cancel -job: permission denied.

The supplicant's interface is valid or a wireless connection has been established via an access point.

IPP job canceled. jobid=%d.

The spooled job was canceled due to error or user request.

job canceled. jobid=< job ID >

The spooled job was canceled due to error or user request.

LeaseTime=<lease time>(sec), RenewTime=<renew time>(sec).

The spooled job was canceled due to error or user request.

Login to fileserver <file server name> (<IP>), <NDS|BINDERY>

The resource lease time received from the DHCP server is displayed in [lease time] in seconds. The renewal time is displayed in [renew time] in seconds.

Manual [%s] is disable, set authentication key.

When the print server was online, the system logged in to <file server> in NDS or BINDERY mode. The transfer protocol in use is also displayed.

Manual [%s] is disable, set encryption key.

The specified manual SA entry is invalid. Set the authentication key.

Memory allocate error.

The specified manual SA entry is invalid. Set the authentication key.

MIC failure TKIP counter measures started

Memory cannot be obtained. Disconnect the USB cable, and then connect it.

MIC failure TKIP counter measures stopped

The supplicant using TKIP has detected two instances of tampering within 60 seconds of each other and has started countermeasures.

Name registration failed. name=<NetBIOS name>

Countermeasures have stopped after 60 seconds (from the time the supplicant using TKIP started countermeasures against tampering).

Name registration success in Broadcast name=<NetBIOS name>

Name registration of <NetBIOS Name> failed. Change to a different NetBIOS name.

Name registration success. WINS server=<WINS server address> NetBIOS Name=<NetBIOS name>

Name registration by <NetBIOS Name> broadcast was successful.

nbtd start.

Name registration of <NetBIOS Name> to <WINS server address> was successful.

no RADIUS /authentication server

The nbtd (NetBIOS over TCP/IP Daemon) has started.

Open log file <file name>

The supplicant has received a message reporting that a usable RADIUS server cannot be found.

permission denied.

The specified log file was opened when the print server was online.

Print queue <print queue name> cannot be serviced by printer 0, <print server name>

When canceling a job, it was determined after checking the user name and host address that the user's privileges were insufficient. (Does not apply to root privileges.)

print sessions full

The print queue cannot be established when the print server is online. Make sure that the print queue exists on the specified file server.

Required file server (<file server name>) not found

No more print jobs can be accepted. Wait a while before sending any more print jobs.

restarted.

The required file server <file server name> could not be found.

session_IPv4 <community name> not defined.

The LPD has started.

session_IPv6 <community name> not defined.

The requested community name is not defined.

Set context to <NDS context name>

The requested community name is not defined.

server certificate invalid

The NDS context name <NDS context name> has been set.

server identity invalid

The server certificate is invalid. Check the server authentication.

shutdown signal received. network service rebooting...

The specified server name is invalid. Check the server authentication.

smbd start. (NetBIOS)

The smbd service has started.

SMTPC: failed to connect smtp server.

SMBD (Server Message Block Daemon) has been started.

SMTPC: failed to connect smtp server. timeout.

Connection to the SMTP server failed. This could be because no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server, or the specified SMTP server name is incorrect, or the specified SMTP server IP address could not be found in the DNS server, or a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the DNS Server's IP address and SMTP server's IP address, or the SMTP server name and SMTP port number, or the SMTP server's SMTP port number, or the network connection and configuration.

SMTPC: failed to get smtp server ip-address.

Connection to the SMTP server failed due to timeout. This could be because the specified SMTP server name is incorrect, or no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server. Check the SMTP server name, or the network connection and configuration.

SMTPC: no smtp server. connection close.

The SMTP server IP address could not be obtained. This could be because:

• The specified DNS server could not be found.

• No connection to the network has been established.

• An incorrect DNS server is specified.

• The specified SMTP server IP address could not be found in the DNS server.

SMTPC: refused connect by smtp server.

Connection to the SMTP server failed due to no response from SMTP. This could be because a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: username or password wasn't correct. [response code] (information)

Connection to the SMTP server is denied. This could be because server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

[POP3C][xxx.xxx.xxx.xxx]:received error response

An error response was received from the server.

Snmp over IPv4 is ready.

Communication over IPv4 with snmp is available.

Snmp over IPv6 is ready.

Communication over IPv6 with snmp is available.

Snmpd Start.

The snmpd has started. This message is displayed only when the power is turned on.

started.

The direct printing service has started.

started.

The IKE service has started.

Started.

The bonjour (rendezvous) function has started.

stopped

The supplicant is terminating.

success but invalid key

The supplicant received a message reporting that EAP authentication was successful, but the EAPOL key was invalid.

success key received

The supplicant received the EAP-Success key.

supplicant started

The supplicant has started.

supplicant unbound

Although the supplicant has started, the access point is not connected.

terminated.

The IKE service has stopped because no configurations for manual SA or IKE exist.

Terminated.

The bonjour (rendezvous) function is disabled.

The print server received error <error number> during attempt to log in to the network. Access to the network was denied. Verify that the print server name and password are correct.

Login to the file server failed when the print server was online. The print server is not registered or a password is specified. Register the print server without specifying a password.

There is problem in dhcp server operation.

There is a problem with the DHCP server.

If multiple DHCP servers are active on the network, check that they are assigning unique IP addresses to each machine.

trap account is unavailable.

v3Trap cannot be sent. This could be because the Trap destination account is different from the account specified by the machine.

unauthenticated

The authentication failed. The supplicant was denied access to the access point or was not authenticated. This message indicates that the authentication failed. If the authentication fails, this message always appears at the end.

Updated (option name)(value) via DHCPv6 Server

The parameter obtained from the DHCP server has been updated.

usbd is disabled.

Plug and Play is unavailable because the machine is in Security Mode. Enable USBD in Security Mode.

waiting for keys

The supplicant is waiting for the session key.

WINS name registration: No response to server (WINS server address)

There was no response from the WINS server. Check that the correct WINS server address is entered. Also, check that the WINS server is functioning properly.

WINS wrong scopeID=<scope ID>

The scope ID is invalid. Use a valid scope ID.

WPS expired wait walk timer

A WPS access point has not been detected within 120 seconds.

WPS mismatch or no credential

The credential information such as the SSID or a valid authentication method for the machine has not been acquired by WPS.

WPS PBC session overlap.

WPS access points have been detected.

WPS recv message FAIL

NACK has been sent or received via WPS.

WPS recv message M2D

M2D message has been received via WPS.

write error occurred. (diskfull)

A "diskfull" error occurred while the machine was writing to the spool file. Wait for the current print job to finish. When it finishes, more HDD space will be available. Only pages that were spooled when the error occurred will be printed.

write error occurred. (fatal)

A "fatal" error occurred while the machine was writing to the spool file. Wait for the current print job to finish. When it finishes, more HDD space will be available. Only pages that were spooled when the error occurred will be printed.

WSD (Device) started.

WSD (Device) has started.

WSD (Printer) started.

WSD (Printer) has started.

WSD (Scanner) started.

WSD (Scanner) has started.