Network

Specify the machine's IPv4 network address.

Default: [Auto-Obtain (DHCP)]

When you select [Specify], enter the IPv4 address and subnet mask as "xxx.xxx.xxx.xxx" ("x" indicates a number).

When you select [Specify], make sure that the IPv4 address is different from that of other machines on the network.

The physical address (MAC address) also appears.

A gateway is a connection or interchange point between two networks.

Specify the gateway address for the router or host computer used as a gateway.

Default: [0.0.0.0]

Display the machine's IPv6 network address.

• Link-local Address

  The machine's specified link-local address appears.

• Manual Configuration Address

  The machine's manually configured address appears.

• DHCPv6 Address

  The machine's DHCPv6 address appears.

• Stateless Address: 1–5

  The specified stateless address appears if [IPv6 Stateless Address Autoconfiguration] is set to [Active].

Display the machine's IPv6 gateway address.

Specify IPv6 Stateless Address Autoconfiguration.

Default: [Active]

Specify the DHCPv6 setting.

Default: [Inactive]

If you set to [Active], select "Operation Mode" from [Router Request], [Obtain IP Address] or [Do not obtain IP Address], and also select "DNS Server Address" from [Auto-Obtain (DHCPv6)] or [Specify].

Make settings for the DNS server.

Default: [Auto-Obtain (DHCP)]

When you select [Specify], enter the DNS Server IPv4 address as "xxx.xxx.xxx.xxx" ("x" indicates a number).

Specify the DDNS settings.

Default: [Active]

Specify the machine's IPsec setting.

Default: [Inactive]

For details about this function, see "Configuring IPsec Settings", Security Guide.

Specify the domain name.

Default: [blank]

When you select [Specify], enter the domain name up to 63 characters.

Specify the WINS server settings.

Default: [On]

If [On] is selected, enter the WINS Server IPv4 address as "xxx.xxx.xxx.xxx" ("x" indicates a number).

If DHCP is in use, specify a Scope ID. Enter the Scope ID up to 31 characters.

Do not enter "255.255.255.255" as the primary or secondary WINS server address.

Select protocols to use in the network.

Default for "IPv4": [Active]

Default for "IPv6": [Inactive]

Default for "SMB": [Active]

Default for "@Remote Service": [Active]

Default for "Firmware Update (IPv4)": [Active]

Default for "Firmware Update (IPv6)": [Active]

Specify the SMB computer name.

Enter the computer name up to 15 characters.

"*+,/:;<>=?[\]|. and spaces cannot be entered.

Do not set a computer name starting with RNP and rnp.

Only use uppercase letters for alphabets.

Specify the SMB work group.

Enter the group name up to 15 characters.

"*+,/:;<>=?[\]|. and spaces cannot be entered.

Only use uppercase letters for alphabets.

Set the access speed for networks.

Default: [Auto Select: Disable 1Gbps]

Select a speed that matches your network environment. [Auto Select: Disable 1Gbps] should usually be selected.

If a connection cannot be established due to hub incompatibility, set [Ethernet Speed] to a setting other than [Auto Select: Enable 1Gbps] or [Auto Select: Disable 1Gbps].

*1 Terms will vary depending on the network.

When you have installed the Wireless LAN interface unit, select the method of connection.

Default: [Ethernet]

[LAN Type] is displayed when wireless LAN board is installed. If Ethernet and Wireless LAN are both connected, the selected interface has priority.

Check the network connection with ping command using the given IPv4 address.

If you fail to connect to the network, check the following, and then retry the ping command.

• Make sure that "IPv4" in [Effective Protocol] is set to [Active].

• Check that the machine with the assigned IPv4 address is connected to the network.

• There is a possibility that the same IPv4 address is used for the specified equipment.

Set the encrypted communication of SNMPv3.

Default: [Encryption / Cleartext]

If you select [Encryption Only], you need to set an encryption password for the machine.

Set the encrypted communication of SSL/TLS.

Default: [Ciphertext Priority]

If you select [Ciphertext Only], you need to install the SSL certificate for the machine.

Specify the host name.

Enter the host name up to 63 characters.

The following host names are unacceptable:

a host name starting with or ending with a hyphen

a host name in which hyphens are used consecutively

a host name starting with "RNP" or "rnp"

Specify the machine name.

Enter the machine name up to 31 characters.

Specify the IEEE 802.1X authentication for Ethernet.

Default: [Inactive]

For details about IEEE 802.1X authentication, see "Configuring IEEE 802.1X Authentication", Security Guide.

You can return the IEEE 802.1X authentication settings to their defaults.

For details about IEEE 802.1X authentication, see "Configuring IEEE 802.1X Authentication", Security Guide.

You can select a USB speed setting.

• Auto Select

• Full Speed

Default: [Auto Select]