Skip header
 

Current Machine Status

This section explains how you can check the machine's status and the items displayed. Depending on the options installed on the machine, some items might not be displayed.

Messages

Description

Access Restricted

The job was canceled because user have no authority.

Adjusting...

The machine is initializing or calibrating.

Call Service Center

There is a malfunction in the machine.

Canceled

The job is reset.

Canceling Job...

The job is being reset.

Cannot Eject Original Through

The original cannot be ejected.

Cannot multi-install: SD Card

SD Card software cannot be installed multi times.

Configuring...

Setting is being changed.

Cooling Down Fusing Unit...

The fusing unit is cooling down.

Cover Open: Front Cover

The front cover is open.

Cover Open: Front Cover

The front cover is open.

Cover Open: Imaging Unit Cover

The mainframe cover is open.

Cover Open: Exit

The paper exit cover is open.

Data Size Error

The data size error occurred.

Empty: Black Toner

The black toner cartridge is almost empty.

Energy Saver Mode

The machine is in Energy Saver mode.

Error

An error has occurred.

Error: Address Book

An error has occurred in the data of the address book.

Error: Command Transmission

An error has occurred in the machine.

Error: DIMM Value

A memory error occurred.

Error: Ethernet Board

An Ethernet board error has occurred.

Error: HDD Board

A hard disk drive board error has occurred.

Error: Media Link Board

An error has occurred on the media link board.

Error: Memory Switch

A memory switch error has occurred.

Error: Optional Font

An error has occurred in the font file of the machine.

Error: Optional RAM

An error has occurred in the optional memory unit.

Error: PDL

An error has occurred in the page description language.

Error: Rem. Certificate Renewal

An error has occurred in the remote server renewal.

Error: USB Board

An error has occurred in the USB interface board.

Error: USB Interface

An error has occurred in the USB interface.

Error: Wireless Card

There is a problem with IEEE802.11a/b/g/n interface unit, or they are not supported.

Full: Front Paper Exit

Front paper exit is full.

Full: Log Data Capacity

The log data capacity is full.

Hex Dump Mode

It is a hex dump mode.

In Use: Copier

The copier is being used.

In Use: Input Tray

Other function is using the input tray.

Independent-supplier Toner

Toner that is not recommended is set.

Jobs Suspended

All jobs are suspended.

Loading Toner...

Toner is being supplied.

Log Data Transfer failed

Log transfer has failed.

Low: Black Toner

The black toner cartridge is not set correctly, or toner is almost running out.

Low: Toner

A toner is almost running out.

Malfunction: Output Tray

There is a problem with the output tray.

Malfunction:Tray 1(PaperRoll 1)

There is a problem with tray 1 (Paper Roll 1).

Malfunction:Tray 2(PaperRoll 2)

There is a problem with tray 2 (Paper Roll 2).

Mismatch: Paper Size

Indicated paper tray does not contain paper of selected size.

Mismatch: Paper Size and Type

Indicated paper tray does not contain paper of selected size and type.

Mismatch: Paper Type

Indicated paper tray does not contain paper of selected type.

Near Replacing: Black PCU

Prepare the new black photoconductor unit.

Near Replacing: Develop. Unit K

Prepare the new development unit (black).

Near Replacing: Fusing Unit

Prepare the new fusing unit.

Nearly Full: Collector Bottle

Collector Bottle is nearly full.

Nearly Full: Log Data Capacity

The log is nearing data capacity.

No Paper: Selected Tray

There is no paper in specified tray.

No Paper: Tray 1(Paper Roll 1)

There is no paper in tray 1 (Paper Roll 1).

No Paper: Tray 2(Paper Roll 2)

There is no paper in tray 2 (Paper Roll 2).

Not Detected: Black Toner

Black toner is not correctly set.

Not Detected: Fusing Unit

The fusing unit is not correctly set.

Not Detected: Input Tray

The paper feed tray is not correctly set.

Not Detected: PCU (K)

The photoconductor unit (black) is not correctly set.

Not Detected: Tray1(PaperRoll1)

Tray 1 (Paper Roll 1) is not correctly set.

Not Detected: Tray2(PaperRoll2)

Tray 2 (Paper Roll 2) is not correctly set.

Not Detected: WasteToner Bottle

Waste toner bottle is not correctly set.

Not Reached, Data Deleted

Unreached job is deleted.

Not Reached, Data Stored

Unreached documents are saved.

Offline

Machine is offline.

Online

Machine is online.

Operating Thermo-range Error

The machine is operating outside the permissible temperature range.

Panel Off Mode

The machine is in Panel-Off mode.

Panel Off Mode>>Printing ava.

The machine is in Control Panel-Off mode.

Paper Error: Remaining in Bypass

Since paper is loaded in the paper bypass, the document can not be printed from the paper trays.

Paper Low: Tray 1(Paper Roll 1)

Tray 1(Paper Roll1) is almost out of paper.

Paper Low: Tray 2(Paper Roll 2)

Tray 2(Paper Roll2) is almost out of paper.

Paper Misfeed: Paper Tray

The paper has jammed in the paper tray.

Paper Misfeed: Internal/Output

The paper has jammed inside the printer.

Prepaid Card not inserted

The machine is waiting for Prepaid Card to be inserted, or the card is empty.

Print Complete

The machine is done printing.

Printing...

Printing is in progress.

Proxy User/Password Incorrect

The proxy user name and/or password setting is incorrect.

Readjusting...

The machine is under readjustment.

Ready

The machine is ready to print.

Renewing Remote Certificate

The remote certificate is being renewed.

Replace Black PCU

Need to replace the Black PCU.

Replace Charger Kit

Need to replace the Charger Kit.

Replace Cleaning Web

Cleaning Web is almost out.

Replace Develop. Unit

Need to replace the Develop. Unit.

Replace Int. Transfer Unit

Need to replace the Int. Transfer Unit.

Replace Transfer Cleaning Unit

Need to replace the Transfer Cleaning Unit.

Reset IPDS fonts

An error has occurred to IPDS fonts.

Retarding...

The machine is waiting for the retarding sequence to be done.

SD Card Authentication failed

SD card authentication failed.

SD Card not inserted

SD card is not inserted to the machine.

Setting Remotely

Remote setup is being done.

Skipped due to Error

Skipped the job due to an error.

Storage Complete

The storage has completed.

Storage Failed

The storage has failed.

Supplies Order Call failed

The supply order call has failed.

Transmission Aborted

The transmission has been aborted.

Transmission Complete

The transmission has completed.

Transmission Failed

The transmission has failed.

Waiting for Job Suspension

The machine is waiting for job suspension.

Waiting to Confirm Printing

The machine is waiting for confirmation on printing when key card has been inserted.

Warming Up...

The machine is warming up.

Note

  • Check the error contents that may be printed in the configuration page.