Previous
Orientation Override:
Select this setting if any paper orientation cannot be specified in some applications. To prevent an original from being rotated in an unwanted direction, use this setting to specify the orientation of originals when a print job is performed.
Default: [Off]
Collate Type:
Select either [Collate], [Rotating Collate], or [Shift Collate] if the [Collate pages] check box is selected in the printer settings.
Default: [Collate]
Staple:
Specify whether or not to staple delivered prints. When enabling the staple function, specify the staple position.
Default: [Off]
Punch:
Specify whether to make punch holes in the output sheets. When enabling the punch function, specify the punch hole position.
Default: [Off]
Z-fold:
Specify whether or not to make Z-fold for the output sheets.
Default: [Off]
Bottom Fold
Folds prints so that their bottom end segment is on top.
Right Fold
Folds prints so that their rightmost segment is on top.
Left Fold
Folds prints so that their leftmost segment is on top.
Fold Type:
Specify whether or not to fold the output sheets.
Default: [Off]
Half Fold
Folds prints in half along their long edge.
Letter Fold-in
Folds prints into thirds with their two end segments folded one on top of the other.
Letter Fold-out
Folds prints into thirds with their two end segments folded in opposite directions.
Double Parallel Fold
Folds prints in half and then in half again with all folding edges aligned parallel to each other.
Gate Fold
Folds prints into four segments, with their two end segments folded inward.
Half Fold - Print Inside (Finisher Booklet Tray)
Folds prints in half with the printed side facing inside and delivers them to the finisher booklet tray.
Half Fold - Print Outside (Finisher Booklet Tray)
Folds prints in half with the printed side facing outside and delivers them to the finisher booklet tray.
Inside printing
In the print dialog box, specify only the type of fold that you require. By default, the print will appear on the inside of the folds.
If you want the folded sheets to open to the left or top, you must also select [Rotate by 180 degrees] in the print dialog box.
Outside printing
If you want the print to appear on the outside of the folds, in the print dialog box you must select [Letter Fold-out] for the type of fold. When this fold is selected, the print appears on the outside of the folds by default. If you select any other type of fold, the print will appear on the inside of the folds. If you want the folded sheets to open to the left or top, you must also select [Rotate by 180 degrees] in the print dialog box.
If you want to specify other types of fold, use one of the following procedures.
When one-sided printing is enabled
In the print dialog box, select the fold type you require and set [Eject Face-up] to [On]. If you want the folded sheets to open to the left or top, you must also select [Rotate by 180 degrees] in the print dialog box.
When duplex printing is enabled
In the print dialog box, select the fold type you require and set [Page Order] to [Reverse]. If you want the folded sheets to open to the left or top, you must also select [Rotate by 180 degrees] in the print dialog box.
In some applications, changing the [Orientation] setting to [Landscape] can result in folded sheets opening in the opposite direction to that specified in the print dialog box.
The reverse order printing function might not work from some applications. If this is the case, specify reverse order printing using the application's settings.
Multi-sheet Fold:
Specify whether or not to fold multiple sheets of paper at a time when [Fold Type] is specified.
Default: [Off]
Up to three sheets can be folded at a time when [Half Fold], [Letter Fold-in], or [Letter Fold-out] is selected in [Fold Type:].
Up to six sheets can be folded at a time when [Half Fold - Print Inside (Finisher Booklet Tray)] is selected in [Fold Type:].
Perfect/Ring Binding:
Specify how to bind the output sheets.
Default: [Off]
Perfect Binding
Applies Perfect Binding to prints.
Ring Binding
Applies Ring Binding to prints.
Punch Only for Ring Binding
Punches Ring Binding holes into prints.
Perfect Binding Position:
Specify a binding position for Perfect Binding.
Default: [Left Bind]
Perfect Binding Paper Source Tray:
Specify a source tray for Perfect Binding.
Default: [Interposer Upper Tray]
Image Position (Along Binding Edge):
Specify a print position in the direction parallel to the binding edge.
Default: [0 mm]
Image Position (Across Binding Edge):
Specify a print position in the direction perpendicular to the binding edge.
Default: [0 mm]
Perfect Binding Cover Sheet Print:
Specify a print side for Perfect Binding Cover Sheet.
Default: [Off]
Perfect Binding Cutting Options:
Specify a cutting option for Perfect Binding.
Default: [Do not Cut]
Perfect Binding Finishing Size:
Specify a finishing size for Perfect Binding.
Default: [Off]
Finishing Size (Along Binding Edge):
Specify a finishing size for Perfect Binding along the binding edge.
Default: [0 mm]
Cut Position Adjustment (Head Edge):
Specify a cut position from the top edge of the paper.
Default: [6.0 mm]
Cut Position Adjustment (Fore Edge):
Specify a cut position from the fore edge of the paper.
Default: [6.0 mm]
Cut Position Adjustment (Tail Edge):
Specify a cut position from the bottom edge of the paper.
Default: [6.0 mm]
Cover Position (Along Binding Edge):
Specify a print position for the cover sheet in the direction parallel to the binding edge.
Default: [0 mm]
Cover Position (Across Binding Edge):
Specify a print position for the cover sheet in the direction perpendicular to the binding edge.
Default: [0 mm]
Ring Binding Position:
Specify a binding position for Ring Binding.
Default: [Left Bind]
Adjust Fore Edge Cut Position:
Specify a cut position for the fore edge.
Default: [Do not Cut]
Eject Face-up:
Specify whether or not to enable face-up outputs.
Default: [Off]
Booklet:
Specify the page order so that you can fold prints into a booklet.
Default: [Off]
