Configuring the Network Interface Board

The following items are displayed: ("Up" indicates enabled; "Down" indicates disabled):.

• Mode

• Protocol Up/Down^*1

  IPv4, IPv6, IPsec, NetWare, SMB

• Device Up/Down^*1

  Parallel, USB, Bluetooth

• Ethernet interface

• Syslog priority

• NVRAM version

• Device name

• Comment

• Location

• Contact

• Soft switch

*1 Parallel and USB are not displayed when the Network Administrator account is logged in to the machine. Only Parallel and USB are displayed when the Machine Administrator account is logged in to the machine.

The following items are displayed: ("Up" indicates enabled; "Down", indicates disabled):.

• Mode (IPv4)

• Mode (IPv6)

  ftp^*1, lpr^*1, rsh^*1, diprint^*1, web, http^*1, ftpc, snmp, ipp^*1, autonet, Bonjour^*1, ssl^*1, nrs, rfu^*1, nbt, ssdp, ssh, sftp^*1, WSD (Device)^{*1 *2}, WSD (Printer), WSD (Scanner), rhpp^*1, llmnr, llmnrc

• IPv4

  DHCP, Address, Netmask, Broadcast, Gateway

• IPv6

  Stateless, Manual, Gateway, DHCPv6, Mode, DUID, IAID, Encode RFC, Previous Lease Address

• IPsec

  Manual Mode, Excluded Protocol^*3 (https, dns, dhcp, wins)

• EncapType^*4

• Host name

• DNS Domain

• Access Control

  IPv4: Access Entry [1]-[5]

  IPv6: Access Entry^*5 [1]-[5]

• SNTP Server^{*6 *7}

• Time Zone^*6

• SNTP Server polling time^*6

• SYSLOG server

• Home page URL1

• Home page link name1

• Home page URL2

• Home page link name2

• Help page URL

• RHPP Port

• RHPP timeout

• HTTP Keep –Alive

• HTTP Keep -Alive timeout

*1 Either of the following items is displayed:

- IPv4:Up, IPv6:Up => Up (IPv4/IPv6)

- IPv4:Up, IPv6:Down => Up (IPv4)

- IPv4:Down, IPv6:Up => Up (IPv6)

- IPv4:Down, IPv6:Down => Down

*2 If both IPv4 and IPv6 are enabled, "Up (IPv4/IPv6)" is displayed for " WSD(Device):". However, it works only with IPv4, not with IPv6. If IPv4 and IPv6 under "Protocol Up/Down" in "Common" are Down and Up respectively, "Up (IPv4/IPv6)" may be displayed for "WSD(Device):". However, it does not work with IPv6.

*3 On/Off will be displayed for each protocol that is excluded.

*4 Either of the following items is displayed. IPX is displayed only if an optional NetWare unit is installed:

- IPv4:Up, IPv6:Up, IPX:Up => IPv4 IPv6 IPX

- IPv4:Up, IPv6:Up, IPX:Down => IPv4 IPv6

- IPv4:Up, IPv6:Down, IPX:Up => IPv4 IPX

- IPv4:Down,IPv6:Up, IPX:Up => IPv6 IPX

- IPv4:Up, IPv6:Down, IPX:Down => IPv4

- IPv4:Down, IPv6:Up , IPX:Down => IPv6

- IPv4:Down, IPv6:Down, IPX:Up => IPX

*5 If IPv6 addresses that are excluded from Printer Job Authentication are specified by range, the starting and ending addresses are displayed for AuthFree Entry." If such IPv6 addresses are specified by mask length, the base IP address and mask are displayed for AuthFree Entry."

*6 Items related to the time server are displayed only when the Machine Administrator account is logged in to the machine. In this case, the items under "TCP/IP:" are also displayed.

*7 Either the NTP address or NTP server name is displayed for "SNTP Server".

The following items are displayed:

• EncapType

• RPRINTER number

• Print server name

• File server name

• Context name

• Switch

  Mode, NDS/Bindery, Packet negotiation, Login Mode

• Print job timeout

• Protocol

• SAP interval time

• NDS Tree Name

• Transfer Protocol

The following items are displayed:

• Switch

  Mode, Direct print, Notification

• Workgroup name

• Computer name

• Comment

• Share name [1]

• Protocol

• Client port

• Client auth level

• Client WSD browse

The following items are displayed:

• Host name

• Communication Mode

• SSID

• Channel

• Security

• WEP Authentication

• WEP Encryption key number

• WEP Encryption keys [1]-[4]

• WPA Encryption

• WPA Authentication

• Pre-Shared Key

• User name

• Domain name

• EAP Type

• Password

• Phase 2 user name

• Phase 2 Method TTLS

• Phase 2 Method PEAP

• Server cert.

• Intermediate CA

• Server ID

• Sub domain

• Mic check

The following item is displayed:

• 802.1X Authentication

The following items are displayed:

• IPv4

  Server [1]-[3], Selected IPv4 DNS Server

• IPv6

  Server [1]-[3], Selected IPv6 Dns Server

• Resolver Protocol^*1

*1 This item is displayed only when both IPv4 and IPv6 are enabled.

The following items are displayed:

• ether

• wlan

The following items are displayed:

• ether

• wlan

The following items are displayed:

• ether

  Primary WINS, Secondary WINS

• wlan

  Primary WINS, Secondary WINS

The following item is displayed:

• Bluetooth mode

The following items are displayed:

• UUID

• Profile

• TTL

The following item is displayed:

• URL

The following items are displayed:

• Computer Name (cname)

• Local Hostname (ether)

• Local Hostname (wlan)

• Location

• Priority (diprint)

• Priority (lpr)

• Priority (ipp)

• IP TTL

• LinkLocal Route for Multi I/F

• IPP Port

The following items are displayed:

• SNMPv1v2

• SNMPv3

• protocol^*1

• v1Trap

• v2Trap

• v3Trap

• SNMPv1v2 Remote Setting

• SNMPv3 Privacy

*1 Either of the following items is displayed. IPX is displayed only if an optional NetWare unit is installed:

- IPv4:Up, IPv6:Up, IPX:Up => IPv4 IPv6 IPX

- IPv4:Up, IPv6:Up, IPX:Down => IPv4 IPv6

- IPv4:Up, IPv6:Down, IPX:Up => IPv4 IPX

- IPv4:Down,IPv6:Up, IPX:Up => IPv6 IPX

- IPv4:Up, IPv6:Down, IPX:Down => IPv4

- IPv4:Down, IPv6:Up , IPX:Down => IPv6

- IPv4:Down, IPv6:Down, IPX:Up => IPX

The following items are displayed:

• Compression

• Port

• TimeOut

• LoginTimeOut

The following items are displayed:

• IPv4

  AuthFree Entry [1]-[5]

• IPv6

  AuthFree Entry^*2 [1]-[5]

• Parallel

• USB

*1 This item is displayed only when the following three conditions are met: user authentication is activated, Printer Job Authentication is set to "Simple (Limitation)", and also when the Machine Administrator account is logged in to the machine.

*2 If IPv6 addresses that are excluded from Printer Job Authentication are specified by range, the starting and ending addresses are displayed for AuthFree Entry." If such IPv6 addresses are specified by mask length, the base IP address and mask are displayed for AuthFree Entry."

The following items are displayed:

• lprm check host

• lpr prnerrchk

The following item is displayed:

• Verification

The following items are displayed:

• Network Device Name

• Comments

• Location

• Presentation URL

• WSD (Device) TCP Port

• WSD (Printer) TCP Port

• WSD (Printer) Job Timeout

• WSD (Scanner) TCP Port

• SSL /TLS

• MetadataVersion

• UUID

The following items are displayed:

• User name

• Domain name

• EAP Type

• Password

• Phase 2 user name

• Phase 2 Method TTLS

• Phase 2 Method PEAP

• Server cert

• Intermediate CA

• Server ID

• Sub domain

"User mode" is displayed.