set

The following command displays the protocol information (up/down).

msh> set ipv4

msh> set ipv6

msh> set ipsec

msh> set netware

• This command is available only when an optional NetWare unit is installed.

msh> set smb

msh> set protocol

• When protocol is specified, information about TCP/IP, NetWare, and SMB appears.

msh> set lpr

msh> set lpr6

msh> set ftp

msh> set ftp6

msh> set rsh

msh> set rsh6

msh> set diprint

msh> set diprint6

msh> set web

msh> set snmp

msh> set ssl

msh> set ssl6

msh> set nrs

msh> set rfu

msh> set rfu6

msh> set ipp

msh> set ipp6

msh> set http

msh> set http6

msh> set bonjour

msh> set bonjour6

msh> set nbt

msh> set ssdp

msh> set ssh

msh> set sftp

msh> set sftp6

msh> set wsdev

msh> set wsdev6

msh> set wsprn

msh> set wsscn

msh> set rhpp

msh> set rhpp6

msh> set lltd

msh> set llmnr

msh> set llmnrc

msh> set chttp

• Enter "up" to enable the protocol, and enter "down" to disable the protocol.

msh> set ipv4 {up|down}

• If you disable IPv4, you cannot use remote access after logging out. If you did this by mistake, you can use the control panel to enable remote access via IPv4.

• Disabling IPv4 also disables lpr, ftp, rsh, diprint, web, snmp, ssl, ipp, http, bonjour, wsdev, and sftp.

msh> set ipv6 {up|down}

• If you disable IPv6, you cannot use remote access after logging out. If you did this by mistake, you can use the control panel to enable remote access via IPv6.

• Disabling IPv6 also disables lpr6, ftp6, rsh6, diprint6, ssl6, ipp6, http6, bonjour6, wsdev6, and sftp6.

msh> set ipsec {up|down}

msh> set netware {up|down}

• This command is available only when an optional NetWare unit is installed.

msh> set smb {up|down}

msh> set lpr {up|down}

msh> set lpr6 {up|down}

msh> set ftp {up|down}

msh> set ftp6 {up|down}

msh> set rsh {up|down}

msh> set rsh6 {up|down}

msh> set diprint {up|down}

msh> set diprint6 {up|down}

msh> set web {up|down}

msh> set snmp {up|down}

msh> set ssl {up|down}

msh> set ssl6 {up|down}

• If the Secured Sockets Layer (SSL, an encryption protocol) function is not available for the printer, you cannot use the function by enabling it.

msh> set nrs {up|down}

msh> set rfu {up|down}

msh> set rfu6 {up|down}

msh> set ipp {up|down}

msh> set ipp6 {up|down}

msh> set http {up|down}

msh> set http6 {up|down}

msh> set bonjour {up|down}

msh> set bonjour6 {up|down}

msh> set ssh {up|down}

msh> set ssdp {up|down}

msh> set nbt {up|down}

msh> set sftp {up|down}

msh> set sftp6 {up|down}

msh> set wsdev {up|down}

msh> set wsdev6 {up|down}

• If "wsdev" and "wsdev6" are enabled simultaneously, both appear as "up" on the protocol information display, but both use IPv4 for WSD (Device), WSD (Printer), and WSD (Scanner).

msh> set wsprn {up|down}

msh> set wsscn {up|down}

msh> set rhpp {up|down}

msh> set rhpp6 {up|down}

msh> set lltd {up|down}

msh> set llmnr {up|down}

msh> set llmnrc {up|down}