Messages Displayed on the Client Computer

“Any of Login User Name, Login Password or Driver Encryption Key is incorrect.”

The entered login user name, password, or driver encryption key was invalid.

Check your login user name, login password, or driver encryption key, and then enter them correctly. For details about login user name, login password, and driver encryption key, see Security Guide.

“Authentication succeeded. However, the access privileges for scanner function has been denied.”

The logged in user name does not have permission for scanner function.

For details about how to set permissions, see Security Guide.

“Cannot add any more scanning mode.”

The maximum number of registerable scan modes has been exceeded.

The maximum number of modes that can be stored is 100. Delete unneeded modes.

“Cannot detect the paper size of the original. Specify the scanning size.”

The set original was misaligned.

• Place the original correctly.

• Specify the scan size.

• When placing an original directly on the exposure glass, the lifting/lowering action of the exposure glass cover or the ADF triggers the automatic original size detection process. Lift the exposure glass cover or the ADF 30 degrees or more.

“Cannot specify any more scanning area.”

The maximum number of registerable scan areas has been exceeded.

The maximum number of scanning areas that can be stored is 100. Delete unneeded scanning areas.

“Clear Misfeed(s) in ADF.”

A paper misfeed has occurred inside the ADF.

• Remove the jammed originals, and then insert them again. For details about jammed paper, see Removing Jammed Paper.

• When a misfeed occurs, replace the jammed originals.

• Check whether the originals are suitable to be scanned by the machine.

“Error has occurred in the scanner driver.”

An error has occurred in the driver.

• Check whether the network cable is connected correctly to the client computer.

• Check whether the Ethernet board of the client computer is recognized correctly by Windows.

• Check whether the client computer can use the TCP/IP protocol.

“Error has occurred in the scanner.”

The application-specified scan conditions have exceeded the setting range of the machine.

Check whether the scanning settings made with the application exceed the setting range of the machine.

“Fatal error has occurred in the scanner.”

An unrecoverable error has occurred on the machine.

An unrecoverable error has occurred in the machine. Contact your service representative.

“Insufficient memory. Close all other applications, then restart scanning.”

Memory is insufficient.

• Close all the unnecessary applications running on the client computer.

• Uninstall the TWAIN driver, and then reinstall it after restarting the computer.

“Insufficient memory. Reduce the scanning area.”

Scanner memory is insufficient.

• Reset the scan size.

• Lower the resolution.

• Set with no compression. For details about the settings, see TWAIN driver Help.

The problem may be due to the following cause:

• Scanning cannot be performed if large values are set for brightness when using halftone or high resolution. For details about the relationship between scan settings, see "Relationship between Resolution and Scan Size", Scan.

• If a misfeed occurs, you might not scan an original. Remove the misfeed, and then scan the original again.

“Invalid Winsock version. Please use version 1.1 or higher.”

You are using an invalid version of Winsock.

Install the operating system of the computer or copy Winsock from the operating system CD-ROM.

“No response from the scanner.”

The machine or client computer is not connected to the network correctly.

• Check whether the machine or client computer is connected to the network correctly.

• Disable the client computer's own firewall. For details about firewall, see Windows Help.

“No response from the scanner.”

The network is crowded.

Wait for a while, and then try to reconnect.

“Scanner is in use for other function. Please wait.”

A function of the machine other than the Scanner function is being used such as the Copier function.

• Wait for a while, and then reconnect.

• Cancel the job that is being processed. Press the [Stop] key. Follow the instructions in the message that appears and exit the function that is running.

“Scanner is not available on the specified device.”

The TWAIN scanner function cannot be used on this machine.

Contact your service representative.

“Scanner is not ready. Check the scanner and the options.”

The ADF cover is open.

Check whether the ADF cover is closed.

“The name is already in use. Check the registered names.”

You tried to register a name that is already in use.

Use another name.