Skip header
 

Loading Envelopes

This section gives you various details about and recommendations concerning envelopes.

Important

  • Do not use window envelopes.

  • Envelopes that are output to the internal tray may be pushed off as successive envelopes are output. If this happens, remove the envelopes as they are output.

  • Fan the envelopes before loading them to separate them and prevent the glue on them from causing them to stick together. If fanning does not prevent them sticking together, load them one by one. Note that some types of envelopes cannot be used with this printer.

  • Misfeeds might occur depending on the length and shape of the flaps.

  • Only envelopes that are at least 139 mm (5.5 inches) wide and whose flaps are open can be loaded in the Portrait orientation.

  • When loading envelopes, load them in the Portrait orientation. If you load envelopes in the Landscape orientation, they might become creased.

  • When loading envelopes in the Portrait orientation, load them with flaps fully open. Otherwise, they might not feed into the printer.

  • Load envelopes in the paper trays as shown below if they are between 139 mm (5.5 inches) and 148 mm (5.9 inches) wide when their flaps are open:

    • Align the envelopes with the right edge of the paper tray.

    • Envelopes may misfeed because there is a gap between the envelopes and the end fence. If this happens, reload the envelopes.

    • Carefully slide the paper tray completely in.

  • Before loading envelopes, press down on them to remove any air from inside, flatten out all four edges. If they are bent or curled, flatten their leading edges (the edge going into the printer) by running a pencil or ruler across them.

The method for loading envelopes varies depending on the orientation of the envelopes. Be sure to load envelopes with the correct orientation.

Types of envelopes

Paper trays 1–4

Bypass tray

Side-opening envelopes Portrait

Illustration of envelope orientation

Illustration of envelope orientation

  • Flaps: open

  • Bottom side of envelopes: toward the right of the printer

  • Side to be printed: face up

Illustration of envelope orientation

  • Flaps: open

  • Bottom side of envelopes: toward the left of the printer

  • Side to be printed: face down

Side-opening envelopes Landscape

Illustration of envelope orientation

Not recommended

Illustration of envelope orientation

  • Flaps: closed

  • Bottom side of envelopes: toward the back of the printer

  • Side to be printed: face down

When loading envelopes, use both User Tools and the printer driver to select "Envelope" as the paper type and specify the thickness of the envelopes. For details, see Printing on Envelopes, Printer.

To print on envelopes that are loaded with their short edges against the printer body, rotate the print image by 180 degrees using the printer driver.

Recommended envelopes

For information about recommended envelopes, contact your local dealer.

The size of envelopes that you can load depends on the tray in which you load them. For details, see Supported Paper for Each Input Tray.

Note

  • Load only one size and type of envelope at a time.

  • The Duplex function cannot be used with envelopes.

  • To achieve better output quality, it is recommended that you set the right, left, top, and bottom print margin to at least 15 mm (0.6 inches) each.

  • The output quality on envelopes may be uneven if parts of an envelope have differing thicknesses. Print one or two envelopes to check the print quality.

  • Printed sheets are delivered to the internal tray even if you specified a different tray.

  • Flatten out prints if they are creased or curled.

  • Check that the envelopes are not damp.

  • High temperature and high humidity conditions can reduce print quality and cause envelopes to become creased.

  • Depending on the environment, printing on envelopes may wrinkle them even if they are recommended.

  • Certain types of envelopes might be output creased, dirtied, or misprinted. If you are printing a solid color on an envelope, lines may appear where the overlapped edges of the envelope make it thicker.