This section describes the user tools in the [Network] menu under [Interface Settings].
Machine IPv4 Address
Specify the machine's IPv4 network address.
Auto-Obtain (DHCP)
Specify
Default: [Auto-Obtain (DHCP)]
When you select [Specify], enter the IPv4 address and subnet mask as "xxx.xxx.xxx.xxx" ("x" indicates a number).
When you select [Specify], make sure that IPv4 address is different from that of another machines on the network.
The physical address (MAC address) also appears.
After changing this setting, turn the machine off, and then turn it on again.
IPv4 Gateway Address
A gateway is a connection or interchange point between two networks.
Specify the gateway address for the router or host computer used as a gateway.
After changing this setting, turn the machine off, and then turn it on again.
Default: 0.0.0.0
Machine IPv6 Address
Displays the machine's IPv6 network address.
Link-Local Address
The machine's specified link-local address appears.
Manual Config. Address
The machine's manually configured address appears.
Stateless Address 1-5
The specified stateless address appears.
IPv6 Gateway Address
Displays the machine's IPv6 gateway address.
IPv6 Stateless Setting
Specify IPv6 Stateless Address Autoconfiguration.
After changing this setting, turn the machine off, and then turn it on again.
Default: [Active]
DNS Configuration
Make settings for the DNS server.
Auto-Obtain (DHCP)
Specify
Default: [Auto-Obtain (DHCP)]
When you select [Specify], enter the DNS Server IPv4 address as "xxx.xxx.xxx.xxx" ("x" indicates a number).
DDNS Configuration
Specify the DDNS settings.
Default: [Active]
Domain Name
Specify the domain name.
After changing this setting, turn the machine off, and then turn it on again.
Auto-Obtain (DHCP)
Specify
Default: [Auto-Obtain (DHCP)]
When you select [Specify], enter the domain name using up to 63 characters.
Effct. Protocol
Select protocols to use in the network.
After changing this setting, turn the machine off, and then turn it on again.
IPv4
Default: [Active]
IPv6
Default: [Inactive]
SMB Work Group
Specify the SMB work group.
Enter the computer name using up to 20 characters.
Ethernet Speed
Set the access speed for networks.
After changing this setting, turn the machine off, and then turn it on again.
Auto Select
100Mbps Full Duplex
100Mbps Half Duplex
10Mbps Full Duplex
10Mbps Half Duplex
Default: [Auto Select]
Select a speed that matches your network environment. [Auto Select] should usually be selected.
Machine Setting |
Settings of the connectable device |
---|---|
Auto Select *1 |
Auto Select, 10Mbps Half Duplex, 100Mbps Half Duplex |
10Mbps Full Duplex |
100Mbps Full Duplex |
10Mbps Half Duplex |
Auto Select, 10Mbps Half Duplex |
100Mbps Full Duplex |
100Mbps Full Duplex |
100Mbps Half Duplex |
Auto Select, 100Mbps Half Duplex |
*1 Terms will vary depending on the network.
LAN Type
Select the method of connection.
After changing this setting, turn the machine off, and then turn it on again.
Ethernet
IEEE 802.11b/g/n
Default: [Ethernet]
Permit SNMPv3 Communictn.
Set the encrypted communication of SNMPv3.
Encryption/Cleartext
Encryption Only
Default: [Encryption/Cleartext]
If you select [Encryption Only], you need to specify the encryption password for the machine.
Permit SSL/TLS Comm.
Set the encrypted communication of SSL/TLS.
Ciphertext Only
Ciphertext Priority
Ciphertext/Cleartext
Default: [Ciphertext/Cleartext]
If you select [Ciphertext Only], you need to install the SSL certificate for the machine.
Auto Email Notify
You can specify whether or not to send notification that a printer error has occurred to a particular e-mail address.
After changing this setting, turn the machine off and then back on.
Default: [Inactive]
Host Name
Specify the host name.
Enter the host name using up to 63 characters.
You cannot enter a host name starting or ending with a hyphen.
You cannot enter a host name starting with "RNP" or "rnp".
Machine Name
Specify the machine name.
Enter the machine name using up to 30 characters.
Restore Network Defaults
Resets the network settings to their default values.