Skip header
 

System Log Information

You can use the following methods to view the system log:

Message

Causes and solutions

add_sess: bad trap addr:<IP Address>, community:<community name>

The IP address (0.0.0.0.) is unavailable when the community access type is TRAP. Specify the host IP address for the TRAP destination.

add_sess: community<community name> already defined.

The same community name already exists. Use another community name.

ANONYMOUS FTP LOGIN FROM <IP address>, <password>

An anonymous login has been made with a password <password> from the host <IP address>.

Change IP address from DHCP Server.

The IP address changes when DHCP LEASE is renewed. To always assign the same IP address, set a static IP address to the DHCP server.

child process exec error! (process name)

The network service failed to start. Turn the printer off and then on. If this does not work, contact your service or sales representatives.

Connected DHCP Server (<DHCP server address>).

The IP address was successfully received from the DHCP server.

connection from <IP address>

Logged on from the host <IP address>

Current Interface Speed:xxxMbps

The speed of the network (10 Mbps or 100 Mbps)

Current IP address <current IP address>

The IP address <current IP address> was received from the DHCP server.

DHCP lease time expired.

DHCP lease time has expired. The printer tries to locate the DHCP server again. The IP address used till now becomes invalid.

DHCP server not found.

The DHCP server cannot be found. Make sure the DHCP server is running on the network.

dhcpcd start.

A dhcpcd (DHCP client server) has started.

Duplicate IP=<IP address>(from <MAC address>).

The same IP address is used. Every IP address must be unique. Check the address of the device indicated in <MAC address>.

exiting

lpd service has ended and the system is closing down.

httpd start.

httpd has started.

inetd start.

An inetd has started.

<interface> started with IP: <IP address>

<IP address> has been set for <Interface> and <Interface> started.

<Interface>: Subnet overlap.

Subnet from Netmask and the IP address you tried to set for <Interface> overlap the subnet of another interface.Set Subnet so it does not overlap with another interface.

IPP cancel-job: permission denied.

The printer could not authenticate the name of the user attempting to cancel a job.

ipp disable.

Printing with ipp is disabled.

ipp enable.

Printing with ipp is enabled.

LeaseTime=<lease time>(sec), RenewTime=<renew time>(sec).

The resource lease time received from the DHCP server is <lease time> in seconds. The renewal time is also <renew time> in seconds.

multid start.

Data transmission service for multiprotocols has started.

Name registration failed. name=<NetBIOS name>

The printer could not register the name of NetBIOS.

Name registration success in Broadcast name=<NetBIOS name>

The NetBIOS name was successfully registered from a broadcast.

Name registration success. WINS Server=<WINS Server Address> NetBIOS Name=<NetBIOS name>

The NetBIOS name was successfully registered to the WINS server.

nbtd start.

nbtd (NetBIOS over TCP/IP Daemon) has started. (Available only in DHCP mode)

permission denied.

Job cancellation was determined to be unauthorized after checking the user name and host address (except for ROOT authorization).

phy release file open failed.

A replacement network interface module is required. Contact your sales or service representatives.

Print sessions full

Cannot accept the print session.

Required computer name (<Computer name>) is duplicated name.

The same computer name is detected on the network. The start job determines the computer name by adding it to the suffix (0,1....). Configure a new computer name that is unique.

restarted.

LPD has started.

session<community name> not defined.

The requested community name is not defined.

shutdown signal received. network service rebooting...

Rebooting the network service.

Snmp over ip is ready.

Communication over TCP/IP via SNMP is available.

snmpd start.

SNMP service has started.

started.

Direct print service has started.

WINS name registration: No response to server (WINS server address)

There is no response from the server during data registration.

Check the WINS server address is correct and WINS server is working properly.

WINS wrong scopeID

The scope ID is wrong.Specify the correct scope ID.