Top Page > Hardware Guide > Installing the Printer and Options > Installing the Printer > Unpacking

Unpacking

To protect it from shock and vibration during transit, this printer comes packaged in cushioning foam and secured with tape. Remove these protective materials after bringing the machine to where it will be installed.

Be sure to locate the machine as close as possible to a wall outlet. This will allow easy disconnection of the power cord in the event of an emergency.

If the machine emits smoke or odours, or if it behaves unusually, you must turn off its power immediately. After turning off the power, be sure to disconnect the power cord plug from the wall outlet. Then contact your service representative and report the problem. Do not use the machine. Doing so could result in fire or electric shock.

If metal objects, or water or other fluids fall inside this machine, you must turn off its power immediately. After turning off the power, be sure to disconnect the power cord plug from the wall outlet. Then contact your service representative and report the problem. Do not use the machine. Doing so could result in fire or electric shock.

Do not touch this machine if a lightning strike occurs in the immediate vicinity. Doing so could result in electric shock.

The following explains the warning messages on the plastic bag used in this product's packaging.
- Keep the polythene materials (bags, etc.) supplied with this machine away from babies and small children at all times. Suffocation can result if polythene materials are brought into contact with the mouth or nose.

Do not incinerate toner (new or used) or toner containers. Doing so risks burns. Toner will ignite on contact with naked flame.

Do not use the cleaner to suck spilled toner (including used toner). Sucked toner may cause firing or explosion due to electrical contact flickering inside the cleaner. However, it is possible to use the cleaner designed for dust explosion-proof purpose. If toner is spilled over the floor, sweep up spilled toner slowly and clean remainder with wet cloth.

Do not store toner (new or used) or toner containers anywhere near naked flames. Doing so risks fire and burns. Toner will ignite on contact with naked flame.

Do not crush or squeeze toner containers. Doing so can cause toner spillage, possibly resulting in dirtying of skin, clothing, and floor, and accidental ingestion.

Store toner (new or used), toner containers, and components that have been in contact with toner out of reach of children.

If toner or used toner is inhaled, gargle with plenty of water and move into a fresh air environment. Consult a doctor if necessary.

If toner or used toner gets into your eyes, flush immediately with large amounts of water. Consult a doctor if necessary.

If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor if necessary.

When moving the machine, use the inset grips on both sides. The machine will break or cause injury if dropped.

During operation, rollers for transporting the paper and originals revolve. A safety device has been installed so that the machine can be operated safety. But take care not to touch the machine during operation. Otherwise, an injury might occur.

Removed tape is dirty. Be careful not to let it touch your hands or clothes.
Leave the tape holding the paper feed tray and cover in place while moving the printer.
Lower the printer slowly and carefully to prevent trapping your hands.
Do not grip on the tray area when lifting the printer.
Do not allow paper clips, staples, or other small metallic objects to fall inside the machine.
Keep the uncovered print cartridge away from direct sunlight.
Do not touch the print cartridge's photo conductor.

Photo conductor unit illustration

Do not touch the ID chip on the side of the print cartridge.

ID chip illustration

Take out the printer from the box, and then remove the plastic bag.

Lift the printer by using the inset grips on both sides of the printer.

Printer illustration

Remove the protective materials attached on the printer's exterior.

Printer illustration

Wait until step 4 before removing the adhesive tape on the rear cover.

Remove the adhesive tape from the rear cover, and then open it.

Printer illustration

Pull out the tape, and then remove the protective materials.

Printer illustration

The actual printer may come with protective materials attached in different positions. Make sure to check the printer's exterior for all protective materials, and remove them completely.

Make sure the levers are pulled up.

Printer illustration

If you leave the levers lowered, toner may not settle properly when printing on standard paper. Make sure the levers are pulled up before printing on standard paper. If not, print may easily smudge or rub off.
After printing envelopes, make sure the levers are pulled up.

Push the side button to open the front cover, and then carefully lower it.

Printer illustration

Remove the protective material attached inside the printer.

Printer illustration

Unpack the print cartridge. Then, place it on a flat surface, and remove the protection sheet.

Print cartridge illustration

Shake the print cartridge from side to side five or six times.

Print cartridge illustration

Slide the print cartridge in horizontally. When the cartridge can go no further, raise it slightly and push it fully in. Then push down on the cartridge until it clicks into place.