Skip header
 

Input / Output

This section describes the user tools in the Input / Output menu under [Copier / Document Server Features].

Switch to Batch

You can select to have Batch mode or SADF mode displayed when you press [Special Original].

Default: [Batch]

SADF Auto Reset

In SADF mode, an original must be placed within a specified time after the previous original has been fed.

Default: [5 seconds]

You can adjust this time from 3 to 99 seconds in increments of 1 second.

Rotate Sort: Auto Paper Continue

Specify whether or not the machine continues copying when paper of the required orientation runs out during rotate sort.

Default: [Off]

  • On

    Copying continues using copy paper of a different orientation. The copy job will finish even if you have left the machine.

  • Off

    When paper of the required orientation runs out, the machine stops copying and prompts you to supply copy paper. After you have loaded paper, the machine will continue copying.

Memory Full Auto Scan Restart

When memory becomes full while scanning originals, the machine can make copies of scanned originals first, and then automatically proceed scanning remaining originals.

Default: [Off]

  • On

    You can leave the machine unattended to make copies, but sorted pages will not be sequential.

  • Off

    When memory becomes full, the machine stops operation allowing you to remove the copy pages delivered on the output tray.

Letterhead Setting

If you select [Yes] in this function, the machine rotates the image correctly.

Default: [No]

Orientation-fixed (top to bottom) or two-sided paper might not be printed correctly depending on how the originals and paper are placed. For details, see "Loading Orientation-Fixed Paper or Two-Sided Paper", Paper Specifications and Adding Paper.

Staple Position

Specify which staple type has priority to be shown on the initial screen.

  • When Finisher SR3090 is installed:

    Default for "Staple Position 1": [Staple: Top 1]

    Default for "Staple Position 2": [Staple: Bottom 1]

    Default for "Staple Position 3": [Staple: Left 2]

    Default for "Staple Position 4": [Staple: Top 2]

  • When Finisher SR3070 is installed: (Types 1 and 2)

    Default for "Staple Position 1": [Staple: Slant]

    Default for "Staple Position 2": [Staple: Bottom Slant]

    Default for "Staple Position 3": [Staple: Left 2]

    Default for "Staple Position 4": [Staple: Top 2]

  • When Booklet Finisher SR3100 is installed: (Types 1 and 2)

    Default for "Staple Position 1": [Staple: Top 1]

    Default for "Staple Position 2": [Staple: Centre]

    Default for "Staple Position 3": [Staple: Left 2]

    Default for "Staple Position 4": [Staple: Top 2]

  • When Finisher SR3120 is installed: (Types 3 and 4)

    Default for "Staple Position 1": [Staple: Top 1]

    Default for "Staple Position 2": [Staple: Bottom 1]

    Default for "Staple Position 3": [Staple: Left 2]

    Default for "Staple Position 4": [Staple: Top 2]

  • When Booklet Finisher SR3110 is installed: (Types 3 and 4)

    Default for "Staple Position 1": [Staple: Slant]

    Default for "Staple Position 2": [Staple: Centre]

    Default for "Staple Position 3": [Staple: Left 2]

    Default for "Staple Position 4": [Staple: Top 2]

Punch Type

Specify which punch type has priority to be shown on the initial screen.

Region A icon(mainly Europe and Asia)

Default for "Punch Type 1": [Punch: 2 Holes Left]

Default for "Punch Type 2": [Punch: 2 Holes Top]

Region B icon(mainly North America)

Default for "Punch Type 1": [Punch: 3 Holes Left]

Default for "Punch Type 2": [Punch: 3 Holes Top]

Simplified Screen: Finishing Types

You can select which key is displayed with higher priority for "Finishing Types" on the simple screen.

Default for "Simplified Screen: Finishing Types 1": [Do not Display]

Default for "Simplified Screen: Finishing Types 2": [Do not Display]

Default for "Simplified Screen: Finishing Types 3": [Do not Display]

Note

  • For details about how to change the Copier / Document Server Features, see "Changing Default Settings", Connecting the Machine/ System Settings.