![]() ![]() ![]() | ![]() | ![]() | |
![]() | |||
![]() | |||
![]() | ![]() | ![]() | ![]() |
![]() | ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() | ![]() ![]() ![]() |
This section explains how you can check the machine's status and the items displayed. Depending on the options installed on the machine, some items might not be displayed.
UNIX: Use the "stat" parameter and the "rsh", "rcp", "ftp", and "sftp" commands. "rsh" and "rcp" cannot be used in a Windows environment.
telnet: Use the "status" command.
Messages |
Description |
---|---|
Access Restricted |
The job was canceled because user have no authority. |
Call Service Center |
There is a malfunction in the machine. |
Canceled |
The job is reset. |
Canceling Job... |
The job is being reset. |
Configuring... |
Setting is being changed. |
Cover Open: Bridge Unit Left |
The cover of the bridge unit left is open. |
Cover Open: Bridge Unit Right |
The cover of the bridge unit right is open. |
Cover Open: Finisher Front |
The front cover of Finisher is open. |
Cover Open: Finisher Upper |
The upper cover of Finisher is open. |
Cover Open: Finisher Safety |
The safety cover of Finisher is open. |
Cover Open: Front Cover |
The front cover is open. |
Cover Open: Lower Right Cover |
The lower right cover is open. |
Cover Open: Right Cover |
The right cover is open. |
Empty: Black Toner |
The black toner cartridge is almost empty. |
Energy Saver Mode |
The machine is in Energy Saver Mode. |
Error: Ethernet Board |
An Ethernet board error has occurred. |
Error: HDD Board |
A hard disk drive board error has occurred. |
Error: Optional Font |
An error has occurred in the font file of the machine. |
Error: Parallel I/F Board |
An error has occurred in the parallel interface. |
Error: PDL |
An error has occurred in the page description language. |
Error: Rem. Certificate Renewal |
An error has occurred in the remote server renewal. |
Error: USB Interface |
An error has occurred in the USB interface. |
Error: Wireless Board |
An error has occurred in the Bluetooth interface unit, the wireless interface board or IEEE 802.11 interface unit. |
Error: Wireless Card |
The wireless card or the Bluetooth interface unit was not installed before start up. |
Full: Finisher Booklet Tray |
Booklet tray of Finisher is full. |
Full: Finisher Shift Tray |
Shift tray of Finisher is full. |
Full: Finisher Upper Tray |
Finisher's upper tray is full. |
Full: Hole Punch Receptacle |
Punch Chip receptacle for hole punch is full. |
Full: Internal Tray 1 |
The internal tray 1 is full. |
Hex Dump Mode |
It is a hex dump mode. |
In Use: Finisher |
Other functions is using Finisher. |
In Use: Input Tray |
Other functions is using the input tray. |
In Use: Staple Unit |
Other functions is using the staple unit. |
Jobs Suspended |
All jobs are suspended. |
Low: Toner |
The toner cartridge is not set correctly, or toner is almost running out. |
Malfunction: Bypass Tray |
There is a problem with the bypass tray. |
Malfunction: Finisher |
There is a problem with the finisher. |
Malfunction: Finisher Tray |
There is a problem with the finisher tray. |
Malfunction: Output Tray |
There is a problem with the output tray. |
Malfunction: Punch Unit |
There is a problem with the punch unit. |
Malfunction: Staple Unit |
There is a problem with the staple unit. |
Malfunction: Tray 1 |
There is a problem with tray 1. |
Malfunction: Tray 2 |
There is a problem with tray 2. |
Malfunction: Tray 3 |
There is a problem with tray 3. |
Malfunction: Tray 4 |
There is a problem with tray 4. |
Miscellaneous Error |
Other error has occurred. |
Mismatch: Paper Size |
Indicated paper tray does not contain paper of selected size. |
Mismatch: Paper Size and Type |
Indicated paper tray does not contain paper of selected size and type. |
Mismatch: Paper Type |
Indicated paper tray does not contain paper of selected type. |
Need more Staples |
Stapler has almost run out of staples. |
No Paper: Selected Tray |
There is no paper in specified tray. |
Not Detected: Duplex Unit |
The duplex feed unit is not correctly set. |
Not Detected: Fusing Unit |
The fusing unit is not correctly set. |
Not Detected: Input Tray |
The paper feed tray is not correctly set. |
Not Detected: PCU |
The photoconductor unit is not correctly set. |
Not Reached, Data Deleted |
Unreached job is deleted. |
Not Reached, Data Stored |
Unreached documents are saved. |
Offline |
Machine is offline. |
Panel Off Mode |
The machine is in Panel-Off mode. |
Paper in Duplex Unit |
The paper remains in the duplex unit. |
Paper in Finisher |
The paper remains in Finisher. |
Paper Misfeed: Duplex Unit |
The paper has jammed in Duplex Unit. |
Paper Misfeed: Finisher |
The paper has jammed in Finisher. |
Paper Misfeed: Input Tray |
The paper has jammed in the input tray. |
Paper Misfeed: Internal Path |
The paper has jammed inside the machine. |
Print Complete |
The print was completed. |
Printing... |
Printing is in progress. |
Processing |
Data is being processed. |
Proxy User/Password Incorrect |
The proxy user name and password setting is incorrect. |
RC Gate Connection Error |
Failed connect with RC Gate (Basil). |
Ready |
The machine is ready to print. |
Renewing Remote Certificate |
The remote certificate is being renewed. |
SD Card Authentication failed |
SD card authentication failed. |
Skipped due to Error |
Skipped the error. |
Storage Complete |
The storage is complete. |
Storage Failed |
The storage has failed. |
Supplies Order Call failed |
The supply order call has failed. |
Transmission Aborted |
The transmission was interrupted. |
Transmission Complete |
The transmission completion was completed. |
Transmission Failed |
The transmission has failed. |
Tray Error: Chaptering |
The paper feed tray specification error has occurred because chaptering as well as the normal paper use the same tray for printing. |
Waiting for Job Suspension |
The machine is waiting for Job Suspension. |
Warming Up... |
The machine is warming up. |
For details about UNIX commands, see UNIX Supplement.
Check the error contents that may be printed in the configuration page.