System Log Information

account is unavailable:

same account name be used.

User account is disabled. This could be because it use the same account name as the administrator account.

account is unavailable:

The authentication password is not set up.

User account is disabled. This could be because the authentication password is not set, and only the encryption account is set.

account is unavailable:

encryption is impossible.

Encryption is not possible and account is disabled. This could be because:

• Security option is not installed.

• Encryption password has not been specified.

add_sess_IPv4: bad trap addr: <IPv4 address>, community: <community name>

The IPv4 address (0.0.0.0.) is unavailable when the community access type is TRAP. Specify the host IPv4 address for the TRAP destination.

add_sess_IPv6: bad trap addr: <IPv6 address>, community: <community name>

The IPv6 address [::] is unavailable when the community access type is TRAP. Specify the host IPv6 address for the TRAP destination.

add_sess_IPv4: community <community name> already defined.

The same community name already exists. Use another community name.

add_sess_IPv6: community <community name> already defined.

The same community name already exists. Use another community name.

connected DHCP server <DHCP server address>

The IP address was successfully received from the DHCP server.

Connected DHCPv6 server <IPv6 address>

The IP address was successfully received from the DHCPv6 server.

connection from <IP address>

A user logged in from the host <IP address>.

Current Interface Speed: xxxMbps

Speed of the network (10 Mbps, or 100 Mbps).

Current IP address <current IP address>

The IP address <current IP address> was acquired from the DHCP server.

DHCP server not found.

The DHCP server was not found. Make sure that the DHCP is on the network.

DHCPv6 server not found.

The DHCPv6 server was not found. Make sure that the DHCPv6 is on the network.

DHCP lease time expired.

The DHCP lease time has expired. Perform the DHCP discover again. The IP address you have been using is no longer available.

Duplicate IP = <IP address> (from <MAC address>).

The same IP address (IPv4, or IPv6 address) was used. Each IP address (IPv4, or IPv6 address) must be unique. Check the address of the device indicated in [MAC address].

inetd start.

The inetd service has started.

Interface (interface name): Duplicate IP Address (<IP address>).

The same IP (IPv4 or IPv6) address was used. Each IP address must be unique. Check the address of the device indicated in [IP address].

< Interface > started with IP: < IP address >

IP address (IPv4 or IPv6 address) has been set for the interface and is operating.

session IPv4 <community name> not defined.

The requested community name is not defined.

session IPv6 <community name> not defined.

The requested community name is not defined.

shutdown signal received. network service rebooting...

The smbd service has started.

SMTPC: failed to get smtp server ip-address.

The SMTP server IP address could not be obtained. This could be because:

• The specified DNS server could not be found.

• No connection to the network has been established.

• The specified DNS server could not be found.

• An incorrect DNS server is specified.

• The specified SMTP server IP address could not be found in the DNS server.

SMTPC: failed to connect smtp server. timeout.

Connection to the SMTP server failed due to timeout. This could be because the specified SMTP server name is incorrect, or no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server. Check the SMTP server name, or the network connection and configuration.

SMTPC: refused connect by smtp server.

Connection to the SMTP server is denied. This could be because server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: no smtp server. connection close.

Connection to the SMTP server failed due to no response from SMTP. This could be because a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: failed to connect smtp server.

Connection to the SMTP server failed. This could be because no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server, or the specified SMTP server name is incorrect, or the specified SMTP server IP address could not be found in the DNS server, or a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the DNS Server's IP address and SMTP server's IP address, or the SMTP server name and SMTP port number, or the SMTP server's SMTP port number, or the network connection and configuration.

SMTPC: username or password wasn't correct. [response code] (information)

Connection to the SMTP server failed, because the specified SMTP user name is incorrect, or the specified SMTP password is incorrect. Check the SMTP user name and password.

Snmp over IPv4 is ready

Communication over IPv4 with snmp is available.

Snmp over IPv6 is ready.

Communication over IPv6 with snmp is available.

Snmpd Start.

The snmpd service has started.

terminated.

The IKE service has stopped because no configurations for manual SA or IKE exist.

There is problem in dhcp server operation.

There is a problem with the DHCP server.

If multiple DHCP servers are active on the network, check that they are assigning unique IP addresses to each machine.

trap account is unavailable.

v3Trap cannot be sent. This could be because the Trap destination account is different from the account specified by the machine.

Updated (option name)(value) via DHCPv6 Server

The parameter obtained from the DHCP server has been updated.

WINS name registration: No response to server

(WINS server address)

There was no response from the WINS server. Check that the correct WINS server address is entered. Also, check that the WINS server is functioning properly.

WINS wrong scope ID=<scope ID>

The scope ID is invalid. Use a valid scope ID.