Input/Output

This section describes the user tools in the Input/Output menu under Copier / Document Server Features.

Switch to Batch

You can select to have Batch mode or SADF mode displayed when you press [Special Original].

Default: [Batch]

Settings made on the main and sub-machines do not affect the connect copy.

SADF Auto Reset

In SADF mode, an original must be set within a specified time after the previous original has been fed.

Default: [5 seconds]

You can adjust this time from 3 to 99 seconds in increments of 1 second.

The main machine applies the settings that have been made on it. Sub-machine settings do not affect connect copy.

Rotate Sort: Auto Paper Continue

Specify whether or not the machine continues copying when paper of the required orientation runs out during rotate sort.

This function is effective when Auto Tray Switching in User Tools (General Features) is set to "On (Rotate)".

Default: [Off]

On
Copying continues using copy paper of a different orientation. The copy job will finish even if you have left the machine.
Off
When paper of the required orientation runs out, the machine stops copying and prompts you to supply copy paper. After you have loaded paper, the machine will continue copying.

The main machine applies the settings that have been made on it. Sub-machine settings do not affect connect copy.

Copy Eject Face Method in Glass Mode

You can specify the way in which copies are delivered when copying an original placed on the exposure glass.

Default: [Face Up]

Settings made on the main and sub-machines do not affect the connect copy.

Copy Eject Face Method in Bypass Mode

You can specify the way in which copies are delivered when copying in bypass mode.

Default: [Face Up]

Settings made on the main and sub-machines do not affect the connect copy.

Memory Full Auto Scan Restart

When memory becomes full while scanning originals, the machine can make copies of scanned originals first, and then automatically proceed scanning remaining originals.

Default: [Off]

On
You can leave the machine unattended to make copies, but sorted pages will not be sequential.
Off
When memory becomes full, the machine stops operation allowing you to remove the copy pages delivered on the output tray.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Insert Separation Sheet

You can specify the number of copy pages for inserting the separation sheet from 1 to 999 pages in increments of 1 page.

Default: [1 set(s)]

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Letterhead Setting

If you select [Yes] in this function, the machine rotates the image correctly.

Default: [No]

Orientation-fixed (top to bottom) or two-sided paper might not be printed correctly depending on how the originals and paper are placed.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Staple Position

Specify which staple type has priority to be shown on the initial display.

Finisher SR4030, Finisher SR5000 or Finisher SR4040 is required to use this function.

When Finisher SR4030 or Finisher SR5000 is installed:
Default for "Staple Position 1": [Top 1]
Default for "Staple Position 2": [Bottom 1]
Default for "Staple Position 3": [Left 2]
Default for "Staple Position 4": [Top 2]
When Finisher SR4040 is installed:
Default for "Staple Position 1": [Top 1]
Default for "Staple Position 2": [Center]
Default for "Staple Position 3": [Left 2]
Default for "Staple Position 4": [Top 2]

The main machine applies the settings that have been made on it. Sub-machine settings do not affect connect copy.

Punch Type

Specify which punch type has priority to be shown on the initial display.

Default for "Punch Type 1": [3 Holes Left]

Default for "Punch Type 2": [3 Holes Top]

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Simplified Screen: Finishing Types

You can select which key is displayed with higher priority for "Finishing Types" on the Simplified Screen.

Default for "Simplified Screen: Finishing Types 1": not programmed

Default for "Simplified Screen: Finishing Types 2": not programmed

Default for "Simplified Screen: Finishing Types 3": not programmed

Settings made on the main and sub-machines do not affect the connect copy.

The connect copy function is not available from the simple display.

Z-fold Output Tray

Specify the tray where Z-fold prints are output to.

Default: [Folding Unit Tray]

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Half Fold Settings

Specify each settings of half fold.

Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
Default: [Off]

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Letter Fold-out Settings

Specify each settings of letter fold-out.

Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Open Orientation
Specify the opening orientation of prints.
Default: [Open to Right] (Open to Top)
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
Default: [Off]

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Letter Fold-in Settings

Specify each settings of letter fold-in.

Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Open Orientation
Specify the opening orientation of prints.
Default: [Open to Right] (Open to Top)
Print Side
Specify which side of sheets is printed on.
Default: [Inside]
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
Default: [Off]

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Double Parallel Fold Settings

Specify each settings of double parallel fold.

Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Open Orientation
Specify the opening orientation of prints.
Default: [Open to Right] (Open to Top)
Print Side
Specify which side of sheets is printed on.
Default: [Inside]

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Gate Fold Settings

Specify each settings of gate fold.

Fold Orientation
Specify the fold orientation of prints.
Default: [Right - Left]
Print Side
Specify which side of sheets is printed on.
Default: [Inside]

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.