set

The following command displays protocol information (active/inactive).

msh> set ipv4

msh> set ipv6

msh> set ipsec

msh> set appletalk

msh> set netware

msh> set smb

msh> set protocol

• When protocol is specified, information about IPv4, IPv6, IPsec, Apple Talk, Netware, and SMB appears.

msh> set parallel

msh> set usb

msh> set lpr

msh> set lpr6

msh> set ftp

msh> set ftp6

msh> set rsh

msh> set rsh6

msh> set diprint

msh> set diprint6

msh> set web

msh> set snmp

msh> set ipp

msh> set ipp6

msh> set http

msh> set http6

msh> set bonjour

msh> set bonjour6

msh> set ssl

msh> set ssl6

msh> set nrs

msh> set rfu

msh> set rfu6

msh> set nbt

msh> set ssdp

msh> set ssh

msh> set sftp

msh> set sftp6

msh> set wsdev

msh> set wsdev6 

msh> set wsprn

msh> set ipds

msh> set rhpp

msh> set rhpp6

• Enter "up" enable protocol, and enter "down" to disable protocol.

  You can set the protocol to "active" or "inactive".

  msh> set ipv4 {up | down}

• If you disable IPv4, you cannot use remote access after logging off. If you did this by mistake, you can use the control panel to enable remote access via IPv4.

• Disabling IPv4 also disables lpr, ftp, rsh, diprint, web, snmp, ssl, ipp, http, bonjour, and sftp.

  msh> set ipv6 {up | down}

• If you disable IPv6, you cannot use remote access after logging off. If you did this by mistake, you can use the control panel to enable remote access via IPv6.

• Disabling IPv6 also disables lpr6, ftp6, rsh6, diprint6, ssl6, ipp6, http6, and sftp6.

  msh> set appletalk {up | down}

  msh> set netware {up | down}

  msh> set smb {up | down}

  msh> set lpr {up | down}

  msh> set lpr6 {up | down}

  msh> set ftp {up | down}

  msh> set ftp6 {up | down}

  msh> set rsh {up | down}

  msh> set rsh6 {up | down}

  msh> set diprint {up | down}

  msh> set diprint6 {up | down}

  msh> set web {up | down}

  msh> set snmp {up | down}

  msh> set ipp {up | down}

  msh> set ipp6 {up | down}

  msh> set http {up | down}

  msh> set http6 {up | down}

  msh> set bonjour {up | down}

  msh> set bonjour6 {up | down}

  msh> set ssl {up | down}

  msh> set ssl6 {up | down}

  • If Secured Sockets Layer (SSL, an encryption protocol) function is not available for the printer, you cannot use the function by enabling it.

  msh> set nrs {up | down}

  msh> set rfu {up | down}

  msh> set rfu6 {up | down}

  msh> set ssh {up | down}

  msh> set ssdp {up | down}

  msh> set nbt {up | down}

  msh> set sftp {up | down}

  msh> set sftp6 {up | down}

  msh> set wsdev {up | down}

  msh> set wsdev6 {up | down}

  • If "wsdev" and "wsdev6" are enabled simultaneously, both appear as "up" on the protocol information display, but both use IPv4 for WS-Device and WS-Printer.

  msh> set wsprn {up | down}

  msh> set ipds {up | down}

  msh> set rhpp {up | down}

  msh> set rhpp6 {up | down}