Skip header
ManualsContentsPreviousNextHelp

Top Page > Software Guide > Making Printer Settings Using the Control Panel > Host Interface Menu > Host Interface Menu Parameters

Host Interface Menu Parameters

This section explains parameters that can be set on the host interface menu.

I/O Buffer

Select the size of I/O Buffer. Normally it is not necessary to change this setting.

Default: [128 KB]

  • 128 KB

  • 256 KB

I/O Timeout

Specify how many seconds the printer should wait before ending a print job. If printing operation is frequently interrupted by data from other ports, you can increase the timeout period.

Default: [15 seconds]

  • 10 seconds

  • 15 seconds

  • 20 seconds

  • 25 seconds

  • 60 seconds

Network

You can make network-related settings.

Machine IPv4 Address

Select whether to set the IPv4 address automatically or manually.

  • Auto-Obtain (DHCP)/Specify (Default: Auto-Obtain (DHCP))

    When DHCP is set to on, the IPv4 address, subnet mask address, and gateway address cannot be changed. To change them, set DHCP to off. Contact your administrator for information about the network configuration.

  • IP Add.

    Manually specify the IPv4 address.

    Default: 11.22. 33.44

  • Subnet M

    Manually specify the subnet mask.

    Default: 0.0.0.0

  • Gateway

    Manually specify the gateway address.

    Default: 0.0.0.0

IPv6 Stateless Setting

Select whether to enable or disable IPv6.

Default: [Active]

  • Active

  • Inactive

IPsec

This is a security function. For details, contact your administrator.

Default: [Inactive]

  • Active

  • Inactive

NW Frame Type

Specify the frame type for NetWare.

Default: [Auto Select]

  • Auto Select

  • Ethernet II

  • Ethernet 802.2

  • Ethernet 802.3

  • Ethernet SNAP

Effective Protocol

Specify the effective protocol.

  • IPv4

    Default: [Active]

    • Active

    • Inactive

  • IPv6

    Default: [Inactive]

    • Active

    • Inactive

  • NetWare

    Default: [Inactive]

    • Active

    • Inactive

  • SMB

    Default: [Active]

    • Active

    • Inactive

  • AppleTalk

    Default: [Inactive]

    • Active

    • Inactive

Ethernet Speed

Specify the network speed to operate the printer.

Default: [Auto Select]

  • Auto Select

  • 10Mbps Half Duplex

  • 10Mbps Full Duplex

  • 100Mbps Half Duplex

  • 100Mbps Full Duplex

IEEE802.1X Auth.(Ethernet)

Specify IEEE 802.1X Ethernet authentication.

Default: [Inactive]

  • Active

  • Inactive

Note

  • For details about IEEE 802.1X authentication, see "Configuration", Hardware Guide.

Restr.IEEE802.1X Auth.Def.

Restore the default IEEE 802.1X setting.

LAN Type

Select Ethernet or Wireless LAN.

Default: [Ethernet]

  • Ethernet

  • Wireless LAN

Note

  • This menu appears only when the optional wireless LAN interface unit is installed.

Parallel Interface

Specify parallel interface settings. This menu appears when the IEEE 1284 interface board is installed.

Parallel Timing

Specify the parallel interface timing.

Default: [ACK outside]

  • ACK inside

  • ACK outside

  • STB down

Parallel Comm. Speed

Specify whether or not to use DMA transfer for receiving data.

Default: [High Speed]

  • High Speed

  • Standard

Selection Signal Status

Specify the selection signal level of the parallel interface.

Default: [High]

  • High

  • Low

Input Prime

You usually do not need to change this setting.

Default: [Inactive]

  • Active

  • Inactive

Bidirectional Comm.

Specify whether to enable or disable bidirectional communication.

Default: [On]

  • On

  • Off

Wireless LAN

Configure settings for wireless LAN. This menu appears only when the optional wireless LAN interface unit is installed.

Communication Mode

Specify the transmission mode for wireless LAN.

Default: [Infrastructure Mode]

  • 802.11 Ad-hoc Mode

  • Infrastructure Mode

SSID Setting

Specify an SSID in infrastructure mode and Ad-hoc Mode.

Default: blank (SSID)

  • SSID

Note

  • Select [?] to enter [/] for the SSID. Also, [\] appears when printing the configuration page, read it as [/].

  • Characters used are ASCII 0x20-0x7e (32 bytes).

  • An SSID is set automatically to the nearest access point if no SSID has been set.

  • If no SSID has been set for Ad-hoc Mode, an SSID is set automatically and the same SSID is used for Ad-hoc Mode and infrastructure mode.

  • If blank is specified in SSID for Ad-hoc Mode, "ASSID" appears.

  • An SSID can also be set using Web Image Monitor. For details, see Web Image Monitor Help.

Ad-hoc Channel

IEEE 802.11a/b/g wireless LAN:

  • 2412 - 2472 MHz (1 - 13 channels)

  • 5180 - 5320 MHz (36, 40, 44, 48, 52, 56, 60, and 64 channels)

IEEE 802.11b/g wireless LAN:

  • 2412 - 2462 MHz (1 - 11 channels)

The channel in use might differ depending on the country.

Security Method

Select whether to enable encryption and specify the security type when the encryption is enabled.

Default: [Off]

  • Off

  • WEP

    Change (HEX), Change (ASCII)

  • WPA

    Encryption Method (TKIP, CCMP(AES)), Authentication Method (WPA-PSK, WPA),(WPA2-PSK), (WPA2)

Note

  • WPA appears only when the optional wireless LAN interface unit is installed.

Wireless LAN Signal

You can check the signal strength when using wireless LAN.

Note

  • This menu appears only when the optional wireless LAN interface unit is installed.

Restore Defaults

Reset the wireless LAN to default.

USB Settings

Select speed for USB interface.

USB Speed

Default: [Auto Select]

  • Auto Select

  • Full Speed

Fixed USB Port

Default: [Off]

  • Level 1

  • Level 2

  • Off

TopPreviousNext
Copyright (C) 2009