Paper Size
You can select the size of the paper loaded in the optional large capacity tray (LCT).
This menu appears only when the LCT is installed.
The paper sizes you can set for Tray 5 (with the optional LCT) are as follows:
[Auto Detect]
51/2×81/2, A5
81/2×11, 51/2×81/2
, A4
, A5
, B5 JIS
You can specify a custom size. To use a custom size paper on this tray, additional setup is required. For details, contact your service representative.
The default setting is Auto Detect.
For details about paper sizes that can be automatically detected, see "Recommended Paper Sizes and Types", About This Machine.
Paper Type
You can set the display so you can see what type of paper is loaded in the paper tray.
The print function uses this information to automatically select the paper tray.
The paper types you can set for the Paper Tray 5 (with the optional LCT) are as follows:
[Do not Display], [Recycled Paper], [Special Paper], [Color Paper 1], [Color Paper 2], [Yellow], [Green], [Blue], [Purple], [Ivory], [Orange], [Pink], [Red], [Gray], [Letterhead], [Translucent Paper], [Preprinted Paper], [Bond Paper], [Cardstock], [OHP (Transparency)], [Prepunched Paper], [Label Paper], [Tab Stock]
Paper Thickness
The paper thicknesses you can set for Tray 5 (with the optional LCT) are as follows:
Plain Paper
52 - 105 g/m2 (14 - 28 lb BOND)
Middle Thick
106 - 163 g/m2 (28 lb BOND - 90 lb INDEX)
Thick Paper 1
164 - 216 g/m2 (90 lb INDEX - 80 lb COVER)
The default setting for "Paper Type" is Do not Display.
The default setting for "Paper Thickness" is Plain Paper.
The default setting for "Apply Duplex" is Yes.
The default setting for "Apply Auto Paper Select" is Yes.
The key mark is displayed next to the paper tray if [No] is selected in "Apply Auto Paper Select".
For details about the relations between possible paper sizes and thickness, see "Recommended Paper Sizes and Types", About This Machine.
For details about the recommended conditions for using thick paper, see "Thick Paper", About This Machine.
The optional tab sheet holder is required when using tab stock in Tray 5.
The Tab Position Shift can be set in millimeters, when Tab Stock has been selected.
The Tab Position Shift can be set in1 inch (1 millimeter) units, within a range of 0 to 0.6 inches (0 to 15 mm). The default is "0.5" inches (13 mm).
Designation Sheet 1 - 9
You can specify and display the paper tray to set designation sheets. You can also specify the display time and copying method for two sided copying.
Select Designation Sheet from 1-9
You can specify paper tray 1-9 as the source trays for designation sheets.
Display Time
You can select [At Mode Selected] or [Full Time].
Apply Duplex
You can select [Yes] or [No].
Cover Sheet Tray
You can specify and display the paper tray to set front cover sheets. You can also specify the display time and copying method for two sided copying.
Display Time
You can select [At Mode Selected] or [Full Time].
Apply Duplex
You can select [Yes] or [No].
Back Cover Sheet Tray
You can specify and display the paper tray to set back cover sheets. You can also specify the display time and copying method for two sided copying.
Display Time
You can select [At Mode Selected] or [Full Time].
Apply Duplex
You can select [Yes] or [No].
Slip Sheet Tray
You can specify and display the paper tray in which to set slip sheets. You can also specify the display time.
Display Time
You can select [At Mode Selected] or [Full Time].
Separation Sheet Tray
You can specify and display the paper tray in which to set slip sheets. You can also specify the display time.
Display Time
You can select [At Mode Selected] or [Full Time].