Edit

Specify left and right margins on the front side of copies in Margin Adjustment mode.

The default setting is Left, 5 mm (Metric version) / Left, 0.2 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Specify left and right margins on the back side of copies in Margin Adjustment mode.

The default setting is Right, 5 mm (Metric version) / Right, 0.2 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Specify top and bottom margins on the front side of copies in Margin Adjustment mode.

The default setting is T/B: 0 mm (Metric version) / T/B: 0.0 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Specify top and bottom margins on the back side of copies in Margin Adjustment mode.

The default setting is T / B: 0 mm (Metric version) / T / B: 0.0 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

In 1 sided to 2 sided Duplex mode, you can specify the margins on the back side.

The margin is set to the same value of "Back Margin: Left/Right".

The default setting is Right, 5 mm (Metric version) / Right, 0.2 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

In 1 sided to 2 sided Duplex mode, you can specify the margins on the back side.

The value set for "Back Margin: Top/Bottom" is used.

The default setting is T / B: 0 mm (Metric version) / T / B: 0.0 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Specify the creep binding margin width.

Range:

• Metric version: 0 to 99 mm (in increments of 1 mm)

• Inch version: 0 to 3.9 inches (in increments of 0.1 inch)

The default setting is 5 mm (Metric version) / 0.2 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Specify the width for erasing border.

The default setting is 10 mm (Metric version) / 0.4 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

In Combine mode, you can specify whether to erase a 3 mm, 0.1 inch boundary margin around all four edges of each original.

The default setting is On.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Specify the width of the erased center margins with this function.

The default setting is 10 mm (Metric version) / 0.4 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

You can make a combined copy on the front cover sheet when you select Front Cover mode.

The default setting is Combine.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

You can set the copy order in Combine mode.

The default setting is From Left to Right.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Select the opening orientation of copies made using Booklet or Magazine mode.

The default setting is Open to Left.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Specify whether to make a combined copy on the inserted slip sheets in Desig./Chapter mode.

The default setting is Combine.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

You can select a separation line using the Image Repeat function from: None, Solid, Broken A, Broken B, or Crop Marks.

• None

  

• Solid

  

• Broken A

  

• Broken B

  

• Crop Marks

  

The default setting is None.

Selecting solid or broken lines might produce a blank area of approximately 1.5 mm (0.06 inch) in width along the separation line.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

You can select a separation line using the Double Copies function from: None, Solid, Broken A, Broken B, or Crop Marks.

• None

  

• Solid

  

• Broken A

  

• Broken B

  

• Crop Marks

  

The default setting is None.

Selecting solid or broken lines might produce a blank area of approximately 1.5 mm (0.06 inch) in width along the separation line.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

You can select a separation line using the Combine function from: None, Solid, Broken A, Broken B, or Crop Marks.

• None

  

• Solid

  

• Broken A

  

• Broken B

  

• Crop Marks

  

The default setting is None.

Selecting solid or broken lines might produce a blank area of approximately 1.5 mm (0.06 inch) in width along the separation line.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

When one-sided copying the back cover, you can specify whether to have the back cover outside (outside page) or inside (inside page).

The default setting is Outside.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

You can select the copy position of bottom or left page according to top or right page as the original image position.

The default setting is Same Position as Original Image Position.

The main machine applies the setting that has been made on it. Sub-machine settings do not affect connect copy.