Use the following command to display the system log information:
UNIX: Use the "syslog" command and "rsh", "rcp", "ftp", and "sftp" parameters.
telnet: Use the "syslog" command.
Message |
Problem and solutions |
---|---|
Access to NetWare server <file server name> denied. Either there is no account for this print server on the NetWare server on the password was incorrect. |
(In the print server mode) Login to the file server failed. Make sure that the print server is registered on the file server. If a password is specified for the print server, delete it. |
account is unavailable: encryption is impossible. |
Encryption is not possible and account is disabled. This could be because:
|
account is unavailable: same account name be used. |
User account is disabled. This could be because it uses the same account name as the administrator account. |
account is unavailable: The authentication password is not set up. |
User account is disabled. This could be because the authentication password is not set, and only the encryption account is set. |
add_sess_IPv4: bad trap addr:<IPv4 address>, community:<community name> |
The IPv4 address (0.0.0.0.) is unavailable when the community access type is TRAP. Specify the host IPv4 address for the TRAP destination. |
add_sess_IPv4: community<community name> already defined. |
The same community name already exists. Use another community name. |
add_sess_IPv6: bad trap addr:<IPv6 address>, community:<community name> |
The IPv6 address [::] is unavailable when the community access type is TRAP. Specify the host IPv6 address for the TRAP destination. |
add_sess_IPv6: community <community name> already defined. |
The same community name already exists. Use another community name. |
add_sess_IPX: bad trap addr:<IPX address>community <community name> |
The IPX address (00:00:00:00:00:00) is unavailable when the community access type is TRAP. Specify the host IPX address for the TRAP destination. |
add_sess_IPX: community <community name> already defined. |
The same community name already exists. Use another community name. |
adjust time server <NTP server> offset:XX sec. |
ncsd tells you the timing of the NTP server and whether or not the time system clock is set. |
Attach FileServer =<file server> |
Connection to the file server as the nearest server has been established. |
Attach to print queue <print queue name> |
(In the print server mode) Attached to the print queue. |
btd is disabled. |
Communication via Bluetooth is unavailable because btd is disabled in the security mode. Enable the btd in the security mode. |
centrod is disabled. |
Communication via parallel connections unavailable because centrod is disabled in the security mode. Enable centrod in the security mode. |
child process exec error! (process name) |
The network service failed to start. Turn the printer off and then on. If this does not work, contact your service or sales representative. |
Connected DHCPv 6 server (IPv 6 address) |
The IP address was successfully received from the DHCPv 6 server. |
connection from <IP address> |
A user logged in from the host <IP address>. |
Could not attach to FileServer <error number> |
(In the remote printer mode) Connection to the file server has not been established. The file server has refused the connection. Check the file server configuration. |
Could not attach to PServer <printer server name> |
(In the remote printer mode) Connection to the print server has not been established. The print server has refused the connection. Check the print server configuration. |
Current Interface Speed: <EhternetI/F speed> |
Speed of the Ehternet interface (10Mbps, 100 Mbps, or 1Gbps). |
Current IPX address <IPX address> |
Current IPX address |
DHCPv6 server not found. |
The DHCPv6 server was not found. Make sure that the DHCPv6 is on the network. |
Duplicate IP=<IP address>(from<MAC address>). |
The same IP address (IPv4, or IPv6 address) was used. Each IP address (IPv4, or IPv6 address) must be unique. Check the address of the device indicated in <MAC address>. |
Established SPX Connection with PServer , (RPSocket=<socket number>, connID=<connection ID>) |
(In the remote printer mode) Connection to the print server has been established. |
Exit pserver |
(In the print server mode) The print server function is disabled because the necessary print server settings have not been made. |
Frametype=<frame type name> |
The frame type name is configured to be used on NetWare. |
IEEE 802.11 <communication mode> mode |
Displays Wireless LAN communication mode (infrastructure, or 802.11 ad hoc). |
IEEE 802.11 Card does NOT support WPA . |
A wireless card that does not support WPA is installed. Install a wireless card that supports WPA. |
IEEE 802.11 Card Firmware REV.<version> |
Displays the version number of the 802.11 card's firmware. |
IEEE 802.11 current channel <channel number> |
Displays the current channel number of the active wireless card (in ad hoc and infrastructure mode). |
IEEE 802.11 MAC Address = <MAC address> |
Displays the MAC address of the wireless interface. |
IEEE 802.11 SSID <ssid> (AP MAC Address <MAC address>) |
The MAC address and SSID of the access point are connected in infrastructure mode. |
(IKE phase-1) mismatched authentication type: local=<authentication type 1> remote=<authentication type 2> |
This machine's <authentication type 1> in IKE phase 1 does not match the communicating host's <authentication type 2>, Make sure this machine's ISAKMP SA authentication type matches that of the communicating host. |
(IKE phase-1) mismatched DH group: local=<DH group number 1> remote=<DH group number 2> |
This machine's ISAKMP SA Oakley group <DH group number 1> in IKE phase 1 does not match the communicating host's ISAKMP SA Oakley group <DH group number 2>, Make sure this machine's ISAKMP SA Oakley group matches that of the communicating host. |
(IKE phase-1) mismatched encryption type: local=<encryption algorithm 1> remote=<encryption algorithm 2> |
This machine's ISAKMP SA Oakley group <encryption algorithm 1> in IKE phase 1 does not match the communicating host's ISAKMP SA Oakley group < encryption algorithm 2>, Make sure this machine's ISAKMP SA Oakley group matches that of the communicating host. |
(IKE phase-1) mismatched hash type: local=<Hash Algorithm 1> remort=<Hash Algorithm 2> |
This machine's ISAKMP SA <Hash Algorithm 1> in IKE phase 1 does not match the communicating host's ISAKMP SA <Hash Algorithm 2>, Make sure this machine's ISAKMP SA Hash Algorithm matches that of the communicating host. |
IKE[%s] is disable, set PSK text. |
|
inetd start. |
The inetd service has started. |
< Interface > started with IP: < IP address > |
IP address (IPv4, or IPv4 address) has been set for the interface and is operating. |
job canceled. jobid=<job ID>. |
The spooled job was canceled due to error or user request. |
LeaseTime=< lease time >(sec), RenewTime=< renew time >(sec). |
The resource lease time received from the DHCP server is displayed in < lease time > in seconds. The renewal time is displayed in < renew time > in seconds. |
Login to fileserver <file server name>(<IPX|IP>,<NDS|BINDERY>) |
(In the print server mode) Login to the file server is in the NDS or BINDERY mode. |
Manual[%s] is disable, set authentication key. |
|
Manual[%s] is disable, set encryption key. |
|
Name registration failed. name=<NetBIOS name> |
Name registration of <NetBIOSName> failed. Change to different NetBIOS name. |
Name registration success . WINS Server =<WINS server address> NetBIOS Name=<NetBIOS name> |
Name registration of <NetBIOS Name> to <WINS server address> was successful. |
Name registration success in Broadcast name =<NetBIOS name> |
Name registration by Broadcast name of <NetBIOS Name> was successful. |
npriter start. (NetWare) |
(In the remote printer mode) The NetWare service has started. |
Open log file <file name> |
(In the print server mode) The specified log file has been opened. |
Print queue <print queue name> cannot be serviced by printer 0, <print server name> |
(In the print server mode) The print queue cannot be established. Make sure that print queue exists on the specified file server. |
Print server <print server name> has no printer |
(In the print server mode) The printer is not assigned to the print server. Using NWadmin, assign the printer, and then restart it. |
print sessions full |
No more print jobs can be accepted. Wait a while before sending any more print jobs. |
Printer <printer name> has no queue |
(In the print server mode) The print queue is not assigned to the printer. Using NWadmin, assign the print queue to the printer, and then restart it. |
pserver start. (NetWare) |
(In the print server mode) The NetWare service has started. |
Required file server (<file server name>) not found |
The required file server is not found. |
sap enable, saptype=<SAP type>, sapname=<SAP name> |
The SAP function has started. The SAP packet is issued to advertise the service on the SAP table on the NetWare server. |
session_IPv4 <community name> not defined. |
The requested community name is not defined. |
session_IPv6 <community name> not defined. |
The requested community name is not defined. |
session_ipx <community name> not defined. |
The requested community name is not defined. |
Set context to <NDS context name> |
An NDS context name has been set. |
shutdown signal received. network service rebooting... |
The smbd service has started. |
Smbd start. (NetBIOS) |
SMBD (ServerMessageBlockDaemon) has been started. |
SMTPC: failed to connect smtp server. |
Connection to the SMTP server failed. This could be because no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server, or the specified SMTP server name is incorrect, or the specified SMTP server IP address could not be found in the DNS server, or a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the DNS Server's IP address and SMTP server's IP address, or the SMTP server name and SMTP port number, or the SMTP server's SMTP port number, or the network connection and configuration. |
SMTPC: failed to connect smtp server. timeout. |
Connection to the SMTP server failed due to timeout. This could be because the specified SMTP server name is incorrect, or no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server. Check the SMTP server name, or the network connection and configuration. |
SMTPC: failed to get smtp server ip-address. |
The SMTP server IP address could not be obtained. This could be because:
|
SMTPC: no smtp server. connection close. |
Connection to the SMTP server failed due to no response from SMTP. This could be because a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number. |
SMTPC: refused connect by smtp server. |
Connection to the SMTP server is denied. This could be because server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number. |
SMTPC: username or password wasn't correct. [response code] (information) |
Connection to the SMTP server failed, because the specified SMTP user name is incorrect, or the specified SMTP password is incorrect. Check the SMTP user name and password. |
Snmp over IPv4 is ready |
Communication over IPv4 with snmp is available. |
Snmp over IPv6 is ready. |
Communication over IPv6 with snmp is available. |
Snmp over IPX is ready. |
Communication over IPX with snmp is available. |
snmpd start. |
The snmpd service has started. |
The print server received error <error number> during attempt to log in to the network. Access to the network was denied . Verify that the print server name and password are correct . |
Login to the file server failed. The print server is not registered or a password is specified. Register the print server without specifying a password. |
trap account is unavailable. |
v3Trap cannot be sent. This could be because the Trap destination account is different from the account specified by the printer. |
Updated (option name) (value) via DHCPv6 Server |
The parameter obtained from the DHCP server has been updated. |
WINS name registration: No response to server (WINS server address) |
There was no response from the WINS server. Check the correct WINS server address is entered. Alternatively, check the WINS server is functioning properly. |
WINS wrong scopeID =< scopeID > |
An invalid scope ID was used. Use a valid scope ID. |
write error occurred.(diskfull) |
A "diskfull" error occurred while the printer was writing to the spool file. Wait for the current print job to finish. When it finishes, more HDD space will be available. Only page that were spooled when the error occurred will be printed. |
write error occurred.(fatal) |
A fatal error occurred while the printer was writing to the spool file. Turn off the power of the printer, and then turn it on again. If the error recurs, contact your service representative. The print job that was being spooled when the error occurred will not be printed. |
For details about UNIX commands and parameters, see UNIX Supplement.
For details about "syslog" command, see Remote Maintenance by telnet.