Skip header
 

Attaching the 500-sheet/1000-sheet/2000-sheet Paper Feed Unit

This section describes how to attach the 500-sheet paper feed unit, 1000-sheet paper feed unit, and 2000-sheet paper feed unit. The procedure is the same for all three units. The 1000-sheet paper feed unit is used as an example.

CAUTION

  • The printer weights approximately 97 kg (214 lb.).

  • Four or more people are required to move the printer. Hold the handles located on both sides, and then lift it slowly. Lifting it carelessly or dropping it may cause an injury.

Important

  • When using the 1000-sheet paper feed unit with the 500-sheet paper feed unit, attach the 500-sheet paper feed unit to the 1000-sheet paper feed unit before attaching to the printer.

  • When the 1000-sheet paper feed unit is attached, the 2000-sheet paper feed unit cannot be attached.

  • When the 2000-sheet paper feed unit is attached, neither the 500-sheet paper feed unit nor the 1000-sheet paper feed unit can be attached.

  • Before using the new paper feed unit, you must configure settings in the printer driver.

  • Four or more people are required for installation.

1Check the contents of the package.

  • Package contents for 500-sheet paper feed unit

    Paper feed unit contents numbered callout illustration

    1. 500-sheet paper feed unit

    2. Two brackets

    3. Three screws

  • Package contents for 1000-sheet paper feed unit

    Paper feed unit contents numbered callout illustration

    1. 1000-sheet paper feed unit

    2. Two brackets

    3. Three screws

  • Package contents for 2000-sheet paper feed unit

    Paper feed unit contents numbered callout illustration

    1. 2000-sheet paper feed unit

    2. Two brackets

    3. Three screws

2Turn the printer off and unplug the power cable.

3Remove the packaging from the paper feed unit.

4When using the 1000-sheet paper feed unit with the 500-sheet paper feed unit, attach the units to each other first, and then attach them to the printer.

For instructions, see "Attaching the 500-sheet Paper Feed Unit to the 1000-sheet Paper Feed Unit".

5Pull out the handle from the right side of the printer.

Exterior front view illustration

6Lift the printer using the handles on both sides of it.

Exterior front view illustration

The printer should always be lifted by at least four people.

7Align the front of the printer with the front of the paper feed unit, and slowly lower it.

Place it so that it is held firmly in place by the vertical pins.

Exterior front view illustration

Return the handle you pulled out from the printer to its original position.

8Pull tray 2 of the printer out slowly until it stops, then lift the front of the tray slightly, and pull it out completely.

Paper tray illustration

Place the tray on a flat surface.

9Attach a screw in the hole on the left side of the tray opening to secure the printer to the paper feed unit.

Tighten the screw firmly using a coin.

Paper tray illustration

10Lift the front of the tray, and slide it carefully into the printer until it stops.

Paper tray illustration

11On the rear of the unit, attach two brackets using the remaining screws.

Tighten the screws firmly using a coin.

Exterior rear view illustration

12Plug in the power cable, and then turn on the printer.

13Print the configuration page to confirm that the unit was attached correctly.

Note

  • To confirm whether the optional paper feed unit was correctly attached, print the configuration page, and check "Attached Equipment" on the configuration page. If the unit was attached correctly, the following will be displayed:

    • 500-sheet paper feed unit: Single Tray

    • 1000-sheet paper feed unit: Twin Trays

    • 2000-sheet paper feed unit: LCT

  • If the optional paper feed unit was not installed properly, repeat the procedure from the beginning. If it cannot be installed correctly even after reattempting installation, contact your sales or service representative.

  • If the print area is not centered correctly, adjust the printing position for the 500-sheet paper feed unit (tray 3) and/or the 1000-sheet paper feed unit (tray 3 to tray 5). For details, see "Adjusting Printing Position".

  • For information about printing the configuration page, see "List/Test Print Menu", Software Guide.

  • To use the 500-sheet, 1000-sheet or 2000-sheet paper feed unit, configure the printer options in "Change Accessories" in the printer driver. For details about opening "Change Accessories", see "Making printer default settings - the printer properties", Software Guide.