System Log Information

account is unavailable: Same account name be used.

User account is disabled. This could be because it use the same account name as the administrator account.

account is unavailable: The authentication password is not set up.

User account is disabled. This could be because the authentication password is not set, and only the encryption account is set.

account is unavailable: encryption is impossible.

Encryption is not possible and account is disabled. This could be because:

• Security option is not installed.

• Encryption password has not been specified.

add_sess_IPv4: bad trap <IPv4 address>, community:<community name>

The IPv4 address (0.0.0.0.) is unavailable when the community access type is TRAP. Specify the host IPv4 address for the TRAP destination.

add_sess_IPv6: bad trap <IPv6 address>, community: <community name>

The IPv6 address [::] is unavailable when the community access type is TRAP. Specify the host IPv6 address for the TRAP destination.

add_sess_IPv4: community <community name> already defined.

The same community name already exists. Use another community name.

add_sess_IPv6: community <community name> already defined.

The same community name already exists. Use another community name.

adjust time server <NTP server> offset:XX sec.

ncsd tells you the timing of the NTP server and whether or not the time system clock is set.

add_sess_IPX: bad trap <IPX address> community <community name>

The IPX address (00:00:00:00:00:00) is unavailable when the community access type is TRAP. Specify the host IPX address for the TRAP destination.

add_sess_IPX: community <community name> already defined.

The same community name already exists. Use another community name.

child process exec error! (process name)

The network service failed to start. Turn the printer off and then on. If this does not work, contact your service or sales representative.

Client password rejected

The client's password was rejected. Check the client password.

Client tls certificate rejected

The client's TLS certificate was rejected. Check the certificate.

Connected DHCPv 6 Server (<DHCPv 6 serveraddress>).

The IP address was successfully received from the DHCPv 6 server.

Current Interface Speed: xxxMbps

Speed of the network (10Mbps, 100 Mbps, or 1Gbps).

DHCPv6 server not found.

The DHCPv6 server was not found. Make sure that the DHCPv6 is on the network.

IEEE 802.11 <communication mode> mode

Displays Wireless LAN communication mode (infrastructure, or 802.11 ad hoc).

IEEE 802.11 Card does NOT support WPA.

A wireless card that does not support WPA is installed. Install a wireless card that supports WPA.

IEEE 802.11 Card Firmware REV.<version>

Displays the version number of the 802.11 card's

firmware.

IEEE 802.11 current channel <channel number>

Displays the current channel number of the active

wireless card (in ad hoc and infrastructure mode).

IEEE 802.11 MAC Address =<MAC address>

Displays the MAC address of the wireless interface.

IEEE 802.11 SSID <ssid> (AP MAC Address <MAC address>)

The MAC address and SSID of the access point are connected in infrastructure mode.

(IKE phase-1) mismatched authentication type: local=<authentication type 1> remote=<authentication type 2>

This machine's <authentication type 1> in IKE phase 1 does not match the communicating host's <authentication type 2>, Make sure this machine's ISAKMP SA authentication type matches that of the communicating host.

(IKE phase-1) mismatched encryption type: <encryption algorithm 1> remote=<encryption algorithm 2>

This machine's ISAKMP SA Oakley group <encryption algorithm 1> in IKE phase 1 does not match the communicating host's ISAKMP SA Oakley group < encryption algorithm 2>, Make sure this machine's ISAKMP SA Oakley group matches that of the communicating host.

(IKE phase-1) mismatched DH group: local=<DH group number 1> remote=<DH group number 2>

This machine's ISAKMP SA Oakley group <DH group number 1> in IKE phase 1 does not match the communicating host's ISAKMP SA Oakley group <DH group number 2>, Make sure this machine's ISAKMP SA Oakley group matches that of the communicating host.

(IKE phase-1) mismatched hash type: local=<Hash Algorithm 1> remote=<Hash Algorithm 2>

This machine's ISAKMP SA <Hash Algorithm 1> in IKE phase 1 does not match the communicating host's ISAKMP SA <Hash Algorithm 2>, Make sure this machine's ISAKMP SA Hash Algorithm matches that of the communicating host.

session IPv4 <community name> not defined.

The requested community name is not defined.

session IPv6 <community name> not defined.

The requested community name is not defined.

session_ipx <community name> not defined.

The requested community name is not defined.

shutdown signal received. network service

rebooting...

The smbd service has started.

SMTPC: failed to get smtp server ip-address.

The SMTP server IP address could not be obtained. This could be because:

• The specified DNS server could not be found.

• No connection to the network has been established.

• The specified DNS server could not be found.

• An incorrect DNS server is specified.

• The specified SMTP server IP address could not be found in the DNS server.

SMTPC: failed to connect smtp server. timeout.

Connection to the SMTP server failed due to timeout. This could be because the specified SMTP server name is incorrect, or no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server. Check the SMTP server name, or the network connection and configuration.

SMTPC: refused connect by smtp server.

Connection to the SMTP server is denied. This could be because server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: no smtp server. connection close.

Connection to the SMTP server failed due to no response from SMTP. This could be because a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: failed to connect smtp server.

Connection to the SMTP server failed. This could be because no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server, or the specified SMTP server name is incorrect, or the specified SMTP server IP address could not be found in the DNS server, or a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the DNS Server's IP address and SMTP server's IP address, or the SMTP server name and SMTP port number, or the SMTP server's SMTP port number, or the network connection and configuration.

SMTPC: username or password wasn't correct. [response code] (information)

Connection to the SMTP server failed, because the specified SMTP user name is incorrect, or the specified SMTP password is incorrect. Check the SMTP user name and password.

Snmp over IPv4 is ready.

Communication over IPv4 with snmp is available.

Snmp over IPv6 is ready.

Communication over IPv6 with snmp is available.

Snmp over IPX is ready.

Communication over IPX with snmp is available.

trap account is unavailable.

v3Trap cannot be sent. This could be because the Trap destination account is different from the account specified by the printer.

Updated (option name) (value) via DHCPv6 Server

The parameter obtained from the DHCP server has been updated.

WSD (Device) started.

WSD (Device) has started.

WSD (Printer) started.

WSD (Printer) has started.