Supported Paper for Each Tray

This section describes the paper size, feed direction, and the maximum amount of paper that can be loaded into each paper tray in this printer.

The following symbols and terminology are used to represent the feed direction.

In this manual	On the display	Paper feed direction
(Feed direction)	A5 (148×210) 5 1/2 × 8 1/2	Short-edge feed direction
(Feed direction)	A5 (210×148) 8 1/2 × 5 1/2	Long-edge feed direction

In this manual

On the display

Paper feed direction

(Feed direction)

A5 (148×210)

5 1/2 × 8 1/2

Short-edge feed direction

(Feed direction)

A5 (210×148)

8 1/2 × 5 1/2

Long-edge feed direction

Be careful of the paper feed direction. The direction is determined for each paper size.

Input Paper Sizes Tray 1

Metric version / Inch version
A4, B5 JIS, A5, 8¹/₂ × 14(Legal), 8¹/₂ × 11(Letter), 5¹/₂ × 8¹/₂

The following sizes are supported but not indicated on the tray dial. You should set the tray dial to "", and select the paper size with the control panel.

Metric version / Inch version
A5, 5¹/₂ × 8¹/₂, 8¹/₄ × 13(Folio), 8¹/₂ × 13(Foolscap), 8 × 13(F/GL), 7.68 × 10¹/₂(16K)

Tray 1 supports custom size paper, approximately 139.7 - 216 mm (5.5 - 8.5 inches) in width, and 139.7 - 356 mm (5.5 - 14.01 inches) in length. Set as custom size using the control panel and printer driver.

The supported size may differ depending on the printer language you use.

Input Paper Sizes Paper Feed Unit (Tray 2/3)

Metric version / Inch version
A4, B5 JIS, A5, 8¹/₂ × 14(Legal), 8¹/₂ × 11(Letter), 5¹/₂ × 8¹/₂

The following sizes are supported but not indicated on the tray dial. You should set the tray dial to "", and select the paper size with the control panel.

Metric version / Inch version
7¹/₄ × 10¹/₂(Executive), 8¹/₄ × 13(Folio), 8¹/₂ × 13(Foolscap), 8 × 13(F/GL), 7.68 × 10¹/₂(16K)

Tray 2/3 supports custom size paper, approximately 139.7 - 216 mm (5.5 - 8.5 inches) in width, and 160 - 356 mm (6.3 - 14.01 inches) in length.

Input Paper Sizes Bypass Tray

The following paper size is supported but the paper size should be set with the control panel.

There is no dial on the tray.

Metric version / Inch version
A4, B5 JIS, A5, A6, 8¹/₂ × 14(Legal), 8¹/₂ × 11(Letter), 5¹/₂ × 8¹/₂, 7¹/₄ × 10¹/₂(Executive), 8¹/₄ × 13(Folio), 8¹/₂ × 13(Foolscap), 8 × 13(F/GL), Com#10 Env, C5 Env, C6 Env, DL Env, Monarch Env, 7.68 × 10¹/₂(16K)

Bypass Tray supports custom size paper, approximately 64 - 216 mm (2.52 - 8.5 inches) in width, and 139.7 - 432 mm (5.5 - 17 inches) in length. Set as custom size using the printer driver.

The supported size may differ depending on the printer language you use.

See Loading Paper.

Input Paper Sizes Envelope Feeder Unit

The following paper size is supported but the paper size should be set with the control panel.

There is no dial on the tray.

Metric version / Inch version
Com#10 Env, C5 Env, C6 Env, DL Env, Monarch Env.

See Loading Paper.

Paper Weight and Number of Sheets to Be Set

	Supported paper weight	Maximum number of sheets (plain paper)
Tray 1	60 - 130 g/m² (16 - 34 lb.)	500 (80 g/m², 20 lb.)
Bypass Tray	60 - 162 g/m² (16 - 43 lb.)	100 (80 g/m², 20 lb.) For other kind of papers, see Types of Paper and Other Media.
Paper Feed Unit (Tray 2, Tray 3)	60 - 130 g/m² (16 - 34 lb.)	500 (80 g/m², 20 lb.)
Envelope Feeder	See Loading Paper.

Check that the top of the stack is not higher than the limit mark inside the tray.

Paper Size Supported by Both Side Printing

The following paper sizes can be printed on both sides:

Metric version / Inch version
A4, B5 JIS, A5, 8¹/₂ × 14(Legal), 8¹/₂ × 11(Letter), 5¹/₂ × 8¹/₂, 8 × 13(F/GL), 8¹/₂ × 13(Foolscap), 8¹/₄ × 13(Folio), 7.68 × 10¹/₂ (16K)

The envelope feeder unit requires the installation of the optional paper feed unit.
Custom paper size is not supported by both sides printing.
JIS stands for "Japanese Industrial Standard".