set

The following command displays protocol information (active/inactive).

msh> set ipv4

msh> set ipv6

msh> set ipsec

msh> set appletalk

msh> set netware

msh> set smb

msh> set protocol

• When protocol is specified, information about TCP/IP, AppleTalk, NetWare and SMB appears.

msh> set lpr

msh> set lpr6

msh> set ftp

msh> set ftp6

msh> set rsh

msh> set rsh6

msh> set diprint

msh> set diprint6

msh> set web

msh> set snmp

msh> set ssl

msh> set ssl6

msh> set nrs

msh> set rfu

msh> set rfu6

msh> set ipp

msh> set ipp6

msh> set http

msh> set http6

msh> set bonjour

msh> set bonjour6

msh> set nbt

msh> set ssdp

msh> set ssh

msh> set sftp

msh> set sftp6

msh> set wsdev

msh> set wsdev6 

msh> set wsprn

msh> set rhpp

msh> set rhpp6

• Enter "up" to enable protocol, and enter "down" to disable protocol.

You can set the protocol to "active" or "inactive".

msh> set ipv4 {up|down}

• If you disable IPv4, you cannot use remote access after logging off. If you did this by mistake, you can use the control panel to enable remote access via IPv4.

• Disabling IPv4 also disables lpr, ftp, rsh, diprint, web, snmp, ssl, ipp, http, wsdev, and sftp.

msh> set ipv6 {up|down}

• If you disable IPv6, you cannot use remote access after logging off. If you did this by mistake, you can use the control panel to enable remote access via IPv6.

• Disabling IPv6 also disables lpr6, ftp6, rsh6, diprint6, ssl6, ipp6, http6, bonjour6, wsdev6, and sftp6.

msh> set ipsec {up|down}

msh> set appletalk {up|down}

msh> set netware {up|down}

msh> set smb {up|down}

msh> set lpr {up|down}

msh> set lpr6 {up|down}

msh> set ftp {up|down}

msh> set ftp6 {up|down}

msh> set rsh {up|down}

msh> set rsh6 {up|down}

msh> set diprint {up|down}

msh> set diprint6 {up|down}

msh> set web {up|down}

msh> set snmp {up|down}

msh> set ssl {up|down}

msh> set ssl6 {up|down}

• If Secured Sockets Layer (SSL, an encryption protocol) function is not available for the printer, you cannot use the function by enabling it.

msh> set nrs {up|down}

msh> set rfu {up|down}

msh> set rfu6 {up|down}

msh> set ipp {up|down}

msh> set ipp6 {up|down}

msh> set http {up|down}

msh> set http6 {up|down}

msh> set bonjour {up|down}

msh> set bonjour6 {up|down}

msh> set ssh {up|down}

msh> set ssdp {up|down}

msh> set nbt {up|down}

msh> set sftp {up|down}

msh> set sftp6 {up|down}

msh> set wsdev {up|down}

msh> set wsdev6 {up|down}

• If "wsdev" and "wsdev6" are enabled simultaneously, both appear as "up" on the protocol information display, but both use IPv4 for WSD (Device), and WSD (Printer).

msh> set wsprn {up|down}

msh> set rhpp {up|down}

msh> set rhpp6 {up|down}