Skip header
 

Top Page > Network and System Settings Guide > Connecting the Machine > Using Utilities to Make Network Settings > Interface Settings

Interface Settings

This section describes how to make Interface settings using utilities.

Change settings by using Web Image Monitor, SmartDeviceMonitor for Admin, and telnet.

[Network] image [Machine IPv4 Address] image [Auto-Obtain (DHCP)]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Machine IPv4 Address] image [Specify] image "IPv4 Address"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Machine IPv4 Address] image [Specify] image "Subnet Mask"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [IPv4 Gateway Address]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Machine IPv6 Address] image "Manual Configuration Address"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [IPv6 Gateway Address]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [IPv6 Stateless Address Autoconfiguration]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [DNS Configuration] image [Auto-Obtain (DHCP)]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [DNS Configuration] image [Specify] image "DNS Server 1-3"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [DDNS Configuration]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [IPsec]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Domain Name] image [Auto-Obtain (DHCP)]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Domain Name] image [Specify] image "Domain Name"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [WINS Configuration] image [On] image "Primary WINS Server"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [WINS Configuration] image [On] image "Secondary WINS Server"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [WINS Configuration] image [On] image "Scope ID"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [WINS Configuration] image [Off]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Effective Protocol] image "IPv4"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: You can specify the TCP/IP settings if SmartDeviceMonitor for Admin is communicating with the machine using IPX/SPX.

  • telnet: Can be used for specifying the setting.

[Network] image [Effective Protocol] image "IPv6"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Effective Protocol] image "NetWare"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: You can specify the IPX/SPX settings if SmartDeviceMonitor for Admin is communicating with the machine using TCP/IP.

  • telnet: Can be used for specifying the setting.

[Network] image [Effective Protocol] image "SMB"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Effective Protocol] image "AppleTalk"

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [NCP Delivery Protocol] image [IPX Priority]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [NCP Delivery Protocol] image [TCP / IP Priority]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [NCP Delivery Protocol] image [IPX Only]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [NCP Delivery Protocol] image [TCP / IP Only]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [NW Frame Type] image [Auto Select]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [NW Frame Type] image [Ethernet II]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [NW Frame Type] image [Ethernet 802.2]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [NW Frame Type] image [Ethernet 802.3]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [NW Frame Type] image [Ethernet SNAP]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [SMB Computer Name]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [SMB Work Group]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Ethernet Speed]

  • Web Image Monitor: Cannot be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [IEEE 802.1X Authentication for Ethernet]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [LAN Type] image [Ethernet]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [LAN Type] image [Wireless LAN]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Ping Command]

  • Web Image Monitor: Cannot be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [Permit SNMPv3 Communication] image [Encryption Only]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Permit SNMPv3 Communication] image [Encryption / Cleartext]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Permit SSL / TLS Communication] image [Ciphertext Only]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [Permit SSL / TLS Communication] image [Ciphertext Priority]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [Permit SSL / TLS Communication] image [Ciphertext/Cleartext]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Cannot be used for specifying the setting.

[Network] image [Host Name]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Can be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Network] image [Machine Name]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Wireless LAN] image [Communication Mode] image [802.11 Ad-hoc Mode]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Wireless LAN] image [Communication Mode] image [Infrastructure Mode]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Wireless LAN] image [SSID Setting]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Wireless LAN] image [Ad-hoc Channel]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.

[Wireless LAN] image [Security Method]

  • Web Image Monitor: Can be used for specifying the setting.

  • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.

  • telnet: Can be used for specifying the setting.