System Log Information

Access to NetWare server <file server name> denied. Either there is no account for this print server on the NetWare server on password was incorrect.

Login to the file server failed when the print server was online. Make sure the print server is registered in <file server name>. If a password is specified for the print server, delete the password.

account is unavailable:

Same account name be used.

User account is disabled. This could be because it use the same account name as the administrator account.

account is unavailable:

The authentication password is not set up.

User account is disabled. This could be because the authentication password is not set, and only the encryption account is set.

account is unavailable:

encryption is impossible.

Encryption is not possible and account is disabled. This could be because:

• Security option is not installed.

• Encryption password has not been specified.

add_sess_IPv4: bad trap <IPv4 address>, community: <community name>

The IPv4 address (0.0.0.0.) is unavailable when the community access type is TRAP. Specify the host IPv4 address for the TRAP destination.

add_sess_IPv6: bad trap <IPv6 address>, community: <community name>

The IPv6 address [::] is unavailable when the community access type is TRAP. Specify the host IPv6 address for the TRAP destination.

add_sess_IPv4: community <community name> already defined.

The same community name already exists. Use another community name.

add_sess_IPv6: community <community name> already defined.

The same community name already exists. Use another community name.

add_sess_IPX: bad trap <IPX address> community <community name>

The IPX address (00:00:00:00:00:00) is unavailable when the community access type is TRAP. Specify the host IPX address for the TRAP destination.

add_sess_IPX: community <community name> already defined.

The same community name already exists. Use another community name.

adjust time server <NTP server name> offset: xx sec.

ncsd tells you the timing of the NTP server and whether or not the time system clock is set.

NTP Server: NTP server name

offset: number of seconds of delay (minus number if a time in advance is specified)

ANONYMOUS FTP LOGIN FROM <IP address>, <password>

An anonymous user logged in from the post <IP address> using the password <password>.

Attach FfileSserver=<file server>

Connection to the file server as the nearest server has been established.

Attach to print queue <print queue name>

The system attached to the print queue when the print server goes online.

authenticating

The supplicant is authenticating with the access point (EAP or WPA).

authentication mode mismatch

The authentication mode of the access point is different from the authentication mode of the supplicant.

Use the authentication mode between the access point and the supplicant.

child process exec error !

The network service failed to start. Turn the printer off and then on. If this does not work, contact your service or sales representative.

cipher suite mismatch

The uni-cast/multi-cast suite (TKIP/AES/WEP) of the access point is different from the suite used by the supplicant.

client EAP method rejected

The authentication mode of the access point is different with the authentication mode of the supplicant.

Use the same authentication mode between the access point and the supplicant.

Client password rejected

The client's password was rejected. Check the client password.

Client TLS certificate rejected

The client's TLS certificate was rejected. Check the certificate.

connected DHCPv6 server <IPv6 address>

The IP address was successfully received from the DHCPv6 server.

connecting

The supplicant is waiting for wireless connection to the access point.

Could not attach to FileServer <error number>

Connection to the file server could not be established when the remote printer was online. The file server refused the connection. Check the file server's configuration.

Could not attach to PServer <print server>

Connection to the print server could not be established when the remote printer was online. The print server refused the connection. Check the print server's configuration.

connection from

A user logged in from the host <IP address>.

Current Interface Speed: xxxMbps

Speed of the network (10Mbps, 100 Mbps, or 1Gbps).

Current IPX address <IPX address>

The current IP address is <IPX address>.

DHCPv6 server not found.

The DHCPv6 server was not found. Make sure that the DHCPv6 is on the network.

dpsd is disabled.

Communication via PictBridge is unavailable because PictBridge is disabled in the security mode. Enable PictBridge in the security mode.

Established SPX Connection with PServer, (RPSocket=<socket number>, connID=<connection ID>)

Connection to the print server was established when the remote printer went online.

exiting

The lpd service has ended and the system is exiting the process.

Exit pserver

The print server function was disabled because the necessary print server settings have not been made.

Frametype=<frame type name>

The specified frame type name <frame type name> is for NetWare use.

IEEE 802.11 Card does NOT support WPA .

A wireless card that does not support WPA is installed. Install a wireless card that supports WPA.

IEEE 802.11 Card Firmware REV.<version>

Displays the version number of the 802.11 card's firmware.

IEEE 802.11 current channel <channel number>

Displays the current channel number of the active wireless card (in ad hoc and infrastructure mode).

IEEE 802.11 MAC Address = <MAC address>

Displays the MAC address of the wireless interface.

IEEE 802.11 SSID <ssid> (AP MAC Address <MAC address>)

The MAC address and SSID of the access point are connected in infrastructure mode.

IEEE 802.11 <communication mode> mode

Displays IEEE 802.11 communication mode.

(IKE phase-1) mismatched authentication type: local=<authentication type 1> remote=<authentication type 2>

This machine's <authentication type> in IKE phase 1 does not match the communicating host's <authentication type 1>, Make sure this machine's <authentication type 2> matches that of the communicating host.

(IKE phase-1) mismatched encryption type: <encryption algorithm 1> remote=<encryption algorithm 2>

This machine's ISAKMP SA Oakley group <encryption algorithm 1> in IKE phase 1 does not match the communicating host's ISAKMP SA Oakley group < encryption algorithm 2>, Make sure this machine's ISAKMP SA Oakley group matches that of the communicating host.

(IKE phase-1) mismatched DH group: local=<DH group number 1> remote=<DH group number 2>

This machine's ISAKMP SA Oakley group <DH group number 1> in IKE phase 1 does not match the communicating host's ISAKMP SA Oakley group <DH group number 2>, Make sure this machine's ISAKMP SA Oakley group matches that of the communicating host.

(IKE phase-1) mismatched hash type: local=<Hash Algorithm 1> remote=<Hash Algorithm 2>

This machine's ISAKMP SA <Hash Algorithm 1> in IKE phase 1 does not match the communicating host's ISAKMP SA <Hash Algorithm 2>, Make sure this machine's ISAKMP SA Hash Algorithm matches that of the communicating host.

Interface (interface name): Duplicate IP Address (<IP address>).

The same IP (IPv4 or IPv6) address was used. Each IP address must be unique. Check the address of the device indicated in [IP address].

<Interface name> card removed

The interface managed by the supplicant has been removed.

<Interface name> interface down

The interface managed by the supplicant is disabled, or cannot connect to the access point.

<Interface name> interface up

The interface managed by the supplicant is enabled, or is connected to the access point.

< Interface > started with IP: < IP address >

IP address (IPv4 or IPv6 address) has been set for the interface and is operating.

< Interface >: Subnet overlap.

The same IP address (IPv4, orIPv6 address) and the subnet mask is used with other device.

job canceled. jobid=%d.

The spooled job was canceled due to error or user request.

LEAP challenge to access point failed

The LEAP challenge to the access point has failed.

Login to fileserver <file server name> (<IPX|IP>), <NDS|BINDERY>

When the print server was online, the system logged in to <file server> in NDS or BINDERY mode. The transfer protocol in use is also displayed.

Memory allocate error.

Date cannot be obtained. Disconnect the USB cable, and then connect it.

MIC failure TKIP counter measures started

The supplicant using TKIP has detected two instances of tampering within 60 seconds and has started counter measures.

MIC failure TKIP counter measures stopped

Counter measures have stopped after 60 seconds (since the supplicant using TKIP started counter measures against tampering).

Name registration failed. name=<NetBIOS name>

Name registration of <NetBIOS Name> failed. Change to a different NetBIOS name.

Name registration success in Broadcast name=<NetBIOS name>

Name registration by <NetBIOS Name> broadcast was successful.

Name registration success. WINS server=<WINS server address> NetBIOS Name=<NetBIOS name>

Name registration of <NetBIOS Name> to <WINS server address> was successful.

no RADIUS/authentication server

The supplicant has received a message reporting that a usable RADIUS server cannot be found.

no smart card detected on device

PEAP/GTC (Generic Token Card) is selected, but a smart card using GTC authentication cannot be found.

no WPA information element in probe response, rescanning

There is no WPA information on the response from the SSID probe of the access point you want to use. The supplicant is rescanning.

Open log file <file name>

The specified log file was opened when the print server was online.

Printer <printer name> has no queue

The print queue is not assigned to the printer when the print server is online. Assign the print queue to the printer using NetWare administrator account, and then restart the printer.

Printer queue <print queue name> cannot be serviced by printer 0, <print server name>

The print queue cannot be established when the print server is online. Make sure that the print queue exists on the specified file server.

Print server <print server name> has no printer

The printer was not assigned to the print server when the print server is online. Use the NetWare administrator account to assign the printer, and then restart the printer.

Print sessions full

No more print jobs can be accepted. Wait a while before sending any more print jobs.

pserver start. (NetWare)

The NetWare service starts when the print server goes online.

Required file server (<file server name>) not found

The required file server <file server name> could not be found.

sap enable. saptype=<SAP type>, sapname=<SAP name>

The SAP function was been started. The SAP packet is issued to advertise the service in the SAP table on the NetWare server.

server certificate invalid

The server ID is disabled. Check the server authentication.

server identity invalid

The server ID is disabled. Check the server authentication.

server not trusted

The RADIUS server cannot be trusted.

session IPv4 <community name> not defined.

The requested community name is not defined.

session IPv6 <community name> not defined.

The requested community name is not defined.

session IPX <community name> not defined.

The requested community name is not defined.

Set context to <NDS contenxt name>

The NDS context name <NDS context name> has been set.

shutdown signal received. network service rebooting...

The smbd service has started.

Smbd start. (NetBIOS)

SMBD (ServerMessageBlockDaemon) has been started.

SMTPC: failed to get smtp server ip-address.

The SMTP server IP address could not be obtained. This could be because:

• The specified DNS server could not be found.

• No connection to the network has been established.

• The specified DNS server could not be found.

• An incorrect DNS server is specified.

• The specified SMTP server IP address could not be found in the DNS server.

SMTPC: failed to connect smtp server. timeout.

Connection to the SMTP server failed due to timeout. This could be because the specified SMTP server name is incorrect, or no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server. Check the SMTP server name, or the network connection and configuration.

SMTPC: refused connect by smtp server.

Connection to the SMTP server is denied. This could be because server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: no smtp server. connection close.

Connection to the SMTP server failed due to no response from SMTP. This could be because a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: failed to connect smtp server.

Connection to the SMTP server failed. This could be because no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server, or the specified SMTP server name is incorrect, or the specified SMTP server IP address could not be found in the DNS server, or a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the DNS Server's IP address and SMTP server's IP address, or the SMTP server name and SMTP port number, or the SMTP server's SMTP port number, or the network connection and configuration.

SMTPC: username or password wasn't correct. [response code] (information)

Connection to the SMTP server failed, because the specified SMTP user name is incorrect, or the specified SMTP password is incorrect. Check the SMTP user name and password.

Snmp over IPv4 is ready

Communication over IPv4 with snmp is available.

Snmp over IPv6 is ready.

Communication over IPv6 with snmp is available.

Snmp over IPX is ready.

Communication over IPX with snmp is available.

success key received

The supplicant received the EAP-Success key.

success but invalid key

The supplicant received a message reporting that EAP authentication was successful, but the EAPOL key was invalid.

supplicant unbound

The supplicant is not connected to the unbound access point.

There is problem in dhcp server operation.

There is a problem with the DHCP server.

If multiple DHCP servers are active on the network, check that they are assigning unique IP addresses to each machine.

too many pictures.

PictBridge printing failed because too many image are sent during one print transaction. Reduce images at one print transaction.

The print server received error <error number> during attempt to log in to the network. Access to the network was denied. Verify that the print server name and password are correct.

Login to the file server failed when the print server was online. The print server is not registered or a password is specified. Register the print server without specifying a password

trap account is unavailable.

v3Trap cannot be sent. This could be because the Trap destination account is different from the account specified by the printer.

unauthenticated

The authentication failed. The supplicant was denied access to the access point, or was not authenticated.

Updated (option name)(value) via DHCPv6 Server

The parameter obtained from the DHCP server has been updated.

usbd is disabled.

Plug and Play is unavailable because the machine is in security mode. Enable USBD in the security mode.

waiting for keys

The supplicant is waiting for the session key.

WINS name registration: No response to server (WINS server address)

There was no response from the WINS server. Check that the correct WINS server address is entered. Also, check that the WINS server is functioning properly.

write error occurred. (diskfull)

A "diskfull" error occurred while the machine was writing to the spool file. Wait for the current print job to finish. When it finishes, more HDD space will be available. Only page that were spooled when the error occurred will be printed.

write error occurred. (fatal)

A "diskfull" error occurred while the machine was writing to the spool file. Wait for the current print job to finish. When it finishes, more HDD space will be available. The print job that was being spooled when the error occurred will not be printed.

WSD (Device) started.

WS-Device has started.

WSD (Printer) started.

WS-Printer has started.

WSD (Scanner) started.

WS-Scanner has started.

#[nfa (process ID)] <time date> + Failed to send logos to a log collection server <IP address>.

An error occurred while trying to send a log file to both the primary and secondary log collection servers.

#[nfa (process ID)] <time date> + Failed to send logs to a collection server <IP address> n time(s) in 1 hour.

60 minutes has passed since the last log entry. During that time, an error occurred while trying to send the log file to both the primary and secondary log collection servers.